LASER ALC-KCUTE Alarm Clock with Night Light User Manual
- June 3, 2024
- Laser
Table of Contents
LASER ALC-KCUTE Alarm Clock with Night Light
Thank you for your purchase
Laser Corporation is 100% Australian owned & operated. To get the most out of
your product please read the user manual carefully and keep for future use.
For specific information relating to your product such as Spare Parts, FAQs,
Warranty claims, and more, please scan the following QR code
WHAT’S IN THE BOX
- Alarm Clock with Night Light
- Ear Attachment
- Charging Cable
- User Manual
SPECIFICATIONS
Temperature Range:| -20°C – 50°C or
-4°F – 122°F
---|---
Time Format:| 12 & 24HR
Charging Input:| DC 3.5V
Battery:| 3.7V, 1200mAh
Charging Time:| 3 hours
Standby Time:| 9 – 200 hours (dependant on LED light use)
Dimensions:| 79 x 66 x 82mm
Weight:| 150g
CONTROLS
Caution: For accurate temperature readings please do not obstruct the sensor.
1.
Light/ Snooze
| – Tap to turn light on/off.
– Double tap when light is off to enter countdown timer mode.
– Double tap when light is
on to check light timer progress bar.
– After alarm rings tap
to snooze.
---|---
2.
Speaker
/Temp Sensor
| – Used to take temperature readings.
– Used for speaker output.
3.
Reset
| – Insert a small object to reset the clock to factory settings.
4.
Time Setting
| – Tap to display the date. The date will be displayed for a few seconds before switching back to
time display.
– Press and hold to enter time setting mode.
---|---
5.
Alarm Setting
| – Tap to display the four alarm groups.
– Double tap to turn the
alarm on/off.
– Press and hold to enter alarm setting mode.
6.
DC 3.5V
Charging Input
| – Plug the included charging cable to recharge the device.
7.
Up
| – Tap to increase value when setting time, alarm, and light timing.
---|---
8.
Down
| – Tap to decrease value when setting time, alarm, and light timing.
DISPLAY
CHARGING
OPERATING INSTRUCTIONS
Setting Time & Date
- Ensure the unit is powered on and in normal display mode. Setting Time & Date
- Press and hold the “Time Setting” button to enter time setting mode.
- Press the “Up” or “Down” button to switch between 12/24HR time.
- Tap the “Time Setting” button to confirm the value and move to the next field.
- The field sequence is as follows: Hour > Minute > Year > Month > Date > Temperature Unit.
- Adjust the values by pressing the “Up” or “Down” button.
- Tap the “Time Setting” button to confirm and move to the next field
- On the temperature unit screen tap the “Up” or “Down” button to switch between Celsius and Fahrenheit.
- After adjusting the temperature unit, tap the “Time Setting” button to finish setting the time & date.
Setting the Alarm
- Ensure the unit is powered on and in normal display mode. Setting the Alarm
- Press and hold the “Alarm Setting” button to enter alarm setting mode.
- Press the “Up” or “Down” button to turn the alarm on/off.
- Tap the “Alarm Setting” button to confirm and move to the next field.
- The field sequence is as follows: Hour > Minute > Day.
- Adjust the values by pressing the “Up” or “Down” button.
- Tap the “Alarm Setting” button to confirm and move to the next field.
- After setting one alarm the unit will prompt you to enter a second alarm. Repeat the previous steps to set another alarm or press the “Up” or “Down” button to turn alternative alarm off. You can set up to 4 alarms.
- After setting the alarm/s tap the “Alarm Setting” button to finish setting the alarm.
Snooze
- After the alarm rings, tap the “Light/Snooze” button to enter snooze mode.
- In snooze mode the alarm will ring again after 5 minutes. Snooze will continue every 5 minutes until the alarm is turned off.
- To turn the alarm off tap the “Alarm Setting” button during the alarm sound.
Countdown Timer
- When the light is off double tap the “Light/Snooze” button to enter/exit countdown timer mode.
- Press the “Up” or “Down” button to select the time range between 0 – 99 minutes.
- After setting a value, tap the “Light/Snooze” button to start the countdown.
- When the countdown has finished the alarm will sound.
- Tap the “Light/Snooze” button to stop the alarm.
Light Timer
- When the light is on double tap the “Light/Snooze” button to enter light timer mode.
- Press the “Up” or “Down” button to select the time range between 10 – 60 minutes.
- The countdown starts after 5 seconds. Once reached the light will turn off.
- Tap the “Light/Snooze” button to exit light timer mode.
TROUBLESHOOTING
No Power
- Check battery level and charge as required.
- Try plugging the USB power cable into an alternative power source such as a USB wall adapter. A computer or laptop port may not provide sufficient current to power/charge the clock.
The Alarm keeps sounding
- If the alarm is in snooze mode it will sound every 5 minutes.
- To turn the alarm off instead of snoozing tap the “Alarm Setting” button during the alarm sound.
- Check the number of alarms you have set. You can set up to 4 alarms.
Visit our websitewww.laserco.com.au
Check us out atwww.youtube.com/lasercoau
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>