LASER TREE LT-80W-AA-PRO 10W Optical Output Power Laser Cutter Module User Manual

LASER TREE LT-80W-AA-PRO 10W Optical Output Power Laser Cutter Module

LASER MODULE INTRODUCTION

Parameters

• DC 12V 3A
• DC 24V 1.5A

Wavelength:| 450nm (+10nm)
Focus length:| 45mm
PWM modulation:| 0/3-12V, 0-5kHz
Fan speed:| 10000rpm
Operating temperature:| 0-60°C
Interface:| XH2.54-3P Socket
Cable:| 3PIN, 80cm
Module size:| 4040147mm
Module weight:| 250g
Application:| Engraving or Cutting

Outline dimension (Unit: mm)

Standard configuration

Air pump suggestion:
Air pressure and capacity: ≥0.027kPa, 27L/min

LASER MODULE CONNECTION DESCRIPTION

PIN Definition

Built-in driver board

Cable

Driver adapter

1. Output A: 3PIN connector
2. Output B: 3PIN connector
3. Input A: 4PIN connector
4. Input B: 4PIN connector
5. Input C: 3PIN connector
6. Input D: 2PIN connector
7. DC Input: 12V or 24V power adapter
8. Power Switch:
   • EXT->External power supply
   • INT->lnternal power supply
9. Power indicator: It is red when the power cable is connected correctly.
10. TTL/PWM indicator: It is green when the TTL/PWM cable is connected correctly.

Connection
Please check whether the laser module is compatible with your engraving machine before connection.

• Check the voltage parameter of your engraving machine.
  Please ensure that your engraving machine voltage and laser module are matched.

• Check the port of the main control board on your engraving machine. Please find the PWM port, GND port and VCC port on the main board of your engraving machine. Then connect this laser module to the main board accordingly.

• “A” &”B”are both compatible.

Connect the laser module to the main board of your engraving machine directly.

Only voltage is not matched.
The voltage parameter of your machine are not matched to the module.

• STEP 1 Connect the cable of your engraving machine to the corresponding input connector on P-DA-01.
• STEP 2 Connect the cable of the laser module to the Output A connector on P-DA-01.
• STEP 3 Connect the corresponding power adapter to the DC Input connector on P-DA-01. Push the switch to EXT position and the power is provided by external power adapter.

Only control board pin definition is not matched.

Situation 1: The definition of connector on the engraving machine main board is not pin-to-pin.
Please rearrange the wire sequence of the cable to make each wire is well matched with the pin definition on the engraving machine main board. Situation 2: Please use P-DA-01 if the main board of your engraving machine is not 3pin, such as 2pin.

• STEP 1 Connect the cable of the your engraving machine to the corresponding input connector on P-DA-01.
• STEP  2 Connect the cable of the laser module to the Output A connector on P-DA-01.

LASER MODULE REFERENCE SETTINGS

For cutting
The focal length of the L T-80W-AA-PRO laser module is 45mm.

When cutting, you only need to make the focus located a bit lower than the surface of materials.

Reference settings for cutting

For engraving

When engraving, please ensure that the focus is located on the material surface.

Reference settings for engraving

PRECAUTIONS AND MAINTENANCE

Precautions

• Laser can damage a person’s skin. Please do not expose your skin directly to the laser.
• Please wear laser goggles to protect your eyes when you use this laser module.
• Please ensure that the air pump is turned on before you start cutting. If not, the smoke will contaminate the lens.
• This laser module doesn’t support hot plug, hot plug may cause damage to the laser module.

Maintenance

• When the laser module is not used for a long time, please ensure that the lens is not polluted by dust.

• When you replace the air nozzle, please ensure that your operation will not pollut the lens. Finger prints or dust on the lens will weaken the output power of the laser module, or even damage the lens.

• ****When you find the cutting ability decreases, the lens might be not clean. Please use a clean alcohol swab to clean it according to the following figure.

• For more information about maintenance, please contact us at lasertree@micost-optotech.com.

Enjoy pleasure of DIV

Documents / Resources

| LASER TREE LT-80W-AA-PRO 10W Optical Output Power Laser Cutter Module [pdf] User Manual
LT-80W-AA-PRO, LT-80W-AA-PRO 10W Optical Output Power Laser Cutter Module, 10W Optical Output Power Laser Cutter Module, Optical Output Power Laser Cutter Module, Output Power Laser Cutter Module, Power Laser Cutter Module, Laser Cutter Module, Cutter Module, Module
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>