LASER TREE LT-80W-F45 Laser Engraving Module with Air Assist User Manual
- May 15, 2024
- LASER TREE
Table of Contents
LASER TREE LT-80W-F45 Laser Engraving Module with Air Assist
PRODUCT INTRODUCTION
Parameters
| Optical power: | 10W (+1W) |
|---|---|
| Input: | DC 12V 3A |
| Wavelength: | 450nm (+10nm) |
| Focus length: | 45mm |
| PWM modulation: | 0/3-12V, 0-5kHz |
| Fan speed: | 10000rpm |
| Operating temperature: | 0-60°C |
| Interface: | XH2.54-3P Socket |
| Cable: | 3PIN, 80cm |
| Module size: | 43*130mm |
| Module weight: | 250g |
| Application: | Engraving or Cutting |
Outline dimension (Unit: mm)
Standard configuration
Air pump suggestion:
- Air pressure and capacity: 0.027kPa, 27L/min
PRODUCT DESCRIPTION
Built-in driver board
PIN definition
Driver adapter
Note: This driver adapter DOES NOT come with the laser module. For more details, please refer to section 3 connection description.
| 1 Output A: 3PIN connector | 2 Output B: 3PIN connector |
|---|---|
| 3 Input A: 4PIN connector | 4 Input B: 4PIN connector |
| 5 Input C: 3PIN connector | 6 Input D: 2PIN connector |
7 DC Input: 12V or 24V power adapter
8 Power Switch: • EXT-External power supply
• INT-internal power supply
9 Power indicator: It is red when the power cable is connected correctly.
10 TTL/PWM indicator: It is green when the TTL/PWM cable is connected
correctly.
CONNECTION DESCRIPTION
Please check whether the laser module is compatible with your engraving machine before connection.
A. Check the voltage parameter of your engraving machine.
Please ensure that your engraving machine voltage and laser module are
matched.
B. Check the port of the main control board on your engraving machine. Please find the PWM port, GND port and VCC port on the main board of your engraving machine. Then connect this laser module to the main board accordingly.
“A”&”B”are both compatible.
Connect the laser module to the main board of your engraving machine directly.
Only voltage is not matched
The voltage parameter of your machine are not matched to the module.
| Laser Module | Machine | Solutions |
|---|---|---|
| 12V | 12V | Plug and play |
| 24V | Driver Adapter + 12V Power Supply |
STEP 1
Connect the cable of your engraving machine to the corresponding input
connector on P-DA-01.
STEP 2
Connect the cable of the laser module to the Output A connector on P-DA-01.
STEP 3
Connect the corresponding power adapter to the DC Input connector on P-DA-01.
Push the switch to EXT position and the power is provided by external power
adapter.
Only control board pin definition is not matched.
Situation 1: The definition of connector on the engraving machine main board is not pin-to-pin.
Please rearrange the wire sequence of the cable to make each wire is well matched with the pin definition on the engraving machine main board.
Situation 2: Please use P-DA-01 if the main board of your engraving machine is not 3pin, such as 2pin.
| Laser Module | Machine | Solutions |
|---|---|---|
| 3PIN | 2PIN | Driver Adapter |
| Other pins | Driver Adapter |
STEP 1
Connect the cable of the your engraving machine to the corresponding input
connector on P-DA-01.
STEP 2
Connect the cable of the laser module to the Output A connector on P-DA-01.
REFERENCE SETTINGS
For cutting
The focal length of the L T-80W-F45 laser module is 45mm.
When cutting, you only need to make the focus located a bit lower than the
surface of materials.
Reference settings for cutting
Focus fixing plate using reference
Material Thinkness| Plate thickness
2mm| 7mm
3mm| 7mm
4mm| 5mm
5mm| 5mm
6mm| 5mm
8mm| 4mm
For engraving
When engraving, please ensure that the focus is located on the material surface.
Reference settings for engraving
PRECAUTIONS
- Laser may cause damage to your skin. Please do not expose your skin directly to the laser.
- Please wear laser goggles to protect your eyes when you use this laser module.
- Please ensure that the air pump is turned on before you start cutting. If not, the smoke will contaminate the lens.
- This laser module doesn’t support hot plug, hot plug may cause damage to the laser module.
MAINTENANCE
- When the laser module is not used for a long time, please ensure that the lens is not polluted by dust.
- When you replace the air nozzle, please ensure that your operation will not pollut the lens. Finger prints or dust on the lens will weaken the output power of the laser module, or even damage the lens.
- When you find the cutting ability decreases, the lens might be not clean. Please use a clean alcohol swab to clean it according to the following figure.
For more information about maintenance, please contact us at lasertree @micost-optotech.com.
Enjoy pleasure of DIV
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>