ANSMANN WFL Series LED Wall Spotlight User Manual

ANSMANN WFL Series LED Wall Spotlight

SAFETY INSTRUCTION

EXPLANATION OF NOTES

Please take note of the following symbols and words used in the operating instructions, on the product, and the packaging:

• Information Useful additional information about the product
• Note The note warns you of possible damage of all kinds
• Caution  Attention – Hazard can lead to injuries
• Warning Attention – Danger! May result in serious injury or death

GENERAL INFO/FOREWORD
Please unpack all parts and check that everything is present and undamaged. Do not use the product if damaged. In this case, contact your local authorized specialist or the service address of the manufacturer.

These operating instructions contain important information for the first use and normal operation of this product, referred to in the following text simply as a lamp or product. Read through the complete operating instructions carefully before using the product for the first time. Keep these operating instructions for future use or future users’ reference. Failure to follow the operating instructions and safety instructions may result in damage to the product and hazards [injuries] for the operator and other persons.

The operating instructions refer to applicable standards and regulations of the European Union. Please also adhere to the laws and guidelines specific to your country.

PROPER INTENDED USE
The product serves as a mobile light source and is not intended for use in other applications. The product is intended exclusively for private, household use and is not suitable for commercial use or for household room lighting and is only for use as described in the operating instructions. Use outside that stipulated in the information is improper use and this can result in damage to property or personal injury. We accept no liability for damage caused by incorrect or improper use.

GENERAL SAFETY INSTRUCTIONS

• This product may be used by children from the age of 8 and by persons with reduced physical, sensory, or mental abilities or lack of experience and knowledge if they have been instructed on the safe use of the product and are aware of the hazards. Children are not permitted to play with the product. Chil­dren are not permitted to carry out cleaning or care without super­vision.
• Keep the product and the packaging away from children. This f:? product is not a toy. Children should be supervised to ensure that they do not play with the product or packaging.
• Avoid eye injuries – Ne­ver look directly into the beam of light or shine it into other people’s faces. If this occurs for too long, the blue light portion of the beam can cause retinal damage.
• Never touch a device that is connected to the mains with wet hands, or if it has fallen into water. In this case, first, switch off the house circuit breaker and then pull out the mains plug.
• Do not expose to po­tentially explosive en­vironments where there are flammable liquids, dust, or gases.
• Never submerge the product in water or other liquids.
• Use only an easily ac­cessible mains socket so that the product can be quickly disconnec­ted from the mains in the event of a fault.
• All illuminated objects must be at least 10cm away from the lamp.
• Use the product exclu­sively with the acces­sories included with it.
• Do not short-circuit connection terminals or batteries.

DANGER OF FIRE AND EXPLOSION

• Do not use it while still in the packaging.
• Do not cover the pro­duct – the risk of fire.
• Never expose the pro­duct to extreme condi­tions, such as extreme heat/ cold, etc.
• Do not use it in the rain or damp areas.

GENERAL INFORMATION

• Do not throw or drop
• The LED cover cannot be replaced. If the cover is damaged, the product must be disposed of.
• The LED light source cannot be replaced. If the LED has reached the end of its service life, the complete lamp must be replaced.
• Do not open or modify the product! Repair work shall only be carried out by the manu­facturer or by a service technician appointed by the manufacturer or by a similarly qualified person.
• Disconnect the device from the power supply only by pulling on the plug or plug housing, never on the cable.
• Information for the light and mains adapter as well as mains voltage on the socket must match with the type plate.
• The lamp shall not be placed face-down or allowed to topple face-down.

ENVIRONMENTAL INFORMATION

DISPOSAL
Dispose of packaging after sorting by material type. Cardboard and cardboard to the waste paper, film to the recycling collection.

• Dispose of the unusable product in accor­A dance with legal provisions. The “waste – -bin” symbol indicates that, in the EU, it is not permitted to dispose of electrical equip­ment in household waste.
• For disposal, pass the product on to a spe­cialist disposal point for old equipment, use the return and collection systems in your area, or contact the dealer from whom you purchased the product.

PART DESCRIPTION

1. LED’s
2. Hinge [360° til table]
3. Cable connector
4. PIR sensor hinge 1
5. PIR sensor hinge 2
6. PIR sensor
7. Mounting bracket
8. 3x control knobs [for the twilight sensor sensitivity, for the PIR sensor detection range, and for the light run time after one activation]

LIABILITY DISCLAIMER

The information contained within these operating instructions can be changed without prior notification. We accept no liability for direct, indirect, incidental or other damage or consequential damage arising though improper handling/use or through disregard of the information contained within these operating instructions.

INSTALLATION INSTRUCTIONS

Note!
Only a VOE-certified waterproof cable H05RN 3xl.Omm2 or H07RN-F 3xl.Dmm2 or better may be used for the connection. Other light sources [e.g. lanterns] can impair the function of the sensor. Do not install the product within the effective range of other light sources.

INSTALLATION

• The fixing holes in the bracket have a diameter of 6 mm. Select a suitable mounting material for this.
• The mounting materials are not supplied. As an example, these instructions show installation with two screws and two dowels. Other mounting materials can be used as required.
• Disconnect the power supply to the cable at the fuse box and secure it against reconnection by third parties. [Fig. 01]
• Determine the installation location and mark the wall. [Fig. 02.1]
• Drill holes at the marked points with an electric drill. [Fig. 02.2]
• Insert the dowels into the drilled holes. [Fig. 02.3]
• Remove the nut of the quick connector. [Fig. 02.4]
• Feed the mains cable through the nut and connect it to the housing. The length of the stripping head and the immersion tube is 8 mm. [Fig. 02.5]

Connect the wires to the respective terminals:

• Blue wire to N [neutral)
• Brown cable to L [phase)
• Green/yellow cable to PE [earth) [Fig. 02.6)
• Tighten the plug. [Fig. 02.7]
• Tighten the nut. [Fig. 02.8]
• Fix the screws, washers, and brackets to the mounting holes. [Fig. 02.9]
• Tighten the screws of the mounting bracket using a suitable tool. [Fig. 02.10]
• Switch the fuse box back on. [Fig. 03]

ADJUSTING THE SPOTLIGHT
The lamp can be angled 90 degrees downwards and 90 degrees upwards. (Fig. D3)

ADJUSTING THE SENSOR

• The sensor can be turned 75 degrees to the left and right, 70 degrees to the front, and 90 degrees to the back. [Fig. 04]
• The product is equipped with a movement sensor, which has a detection angle of 180′ and a maximum detection range of 12 m. [Fig. 05)
• The infrared detector is equipped with three adjustment knobs. [Fig. 06)
• Time setting: You can use this control to select any switch-on time between approx. 10±5 seconds and 5±1 minutes after the last detected movement. Turning the TIME control clockwise reduces the period, and turning it anti-clockwise increases it.

Daylight setting:
The light setting determines the brightness level at which the sensor switches the floodlight on. The sun symbol position indicates that the sensor works during the day and at night and the moon symbol position indicates that the sensor works only at night. To adjust the sensor, wait until the desired ambient brightness is reached. Turn the light setting control fully to the moon symbol and slowly turn the control towards the sun symbol until the floodlight is switched on by the movement. The floodlight is now activated from the set brightness when movement is detected.

Sensitivity setting:
The sensitivity of the sensor depends on the ambient temperature: the lower the ambient temperature, the more sensitive the sensor is.

CLEANING

• Disconnect the power supply from the product at the switch cabinet before any cleaning.
• Secure the product to prevent it from being unintentionally reactivated by attaching a warning sign at the switch cabinet.
• Use only a soft, dry, or slightly moist cloth [with a little mild washing-up liquid if required).
• Do not use abrasive agents or solvents for cleaning.

Subject to technical changes. We assume no liability for printing errors.

DESCRIPTION SYMBOLS

• Class 1 equipment
• Conforms to the European directive
• Risk-Group – Do not look into the lamp
• Waste of Electrical and Electronic Equipment (WEEE-Guideline)
• Battery disposal intimation Not For household waste!
• Read the operating instructions carefully before use!
• Minimum distance from lighted objects
• For harsh conditions
• Safety glass is not replaceable, if the glass is damaged, the product must be discarded.”
• IPXX: IP-Protection class
• Warning! Electrical voltage!

Customer service:

ANSMANN AG
Industriestrasse 10 97959 Assamstadt Germany

Support & FAQ: ansmann.de

• E-Mail: hotline@ansmann.de
• Hotline: +49 (0) 6294 / 4204 3400

МА-1600-0632/1600-0627/1600-0628/1600-0629/V0/04-2024

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>