GRANBERG 611 Disposable Protective Gloves Magic Touch User Manual
- July 27, 2024
- GRANBERG
Table of Contents
GRANBERG 611 Disposable Protective Gloves Magic Touch
Specifications
- Product Code: 114.611
- Standard Compliance: ISO 374-1/Type C, EN ISO 21420:2020, EN ISO 374-1:2016+A1:2018, EN ISO 374-5:2016, EN 421:2010
- Available Sizes: XS, S, M, L, XL
- Permeation Performance Level: 6
- Notified Body: SATRA Technology Europe Ltd. (NB No. 2777)
- Latex Free: Yes
FAQ
- Q: Are these gloves suitable for handling food?
- A: Yes, these gloves are suitable for contact with foodstuffs. However, it is essential to check the Food Declaration of Compliance to ensure suitability for specific types of food.
- Q: What is the lot number and how should I store these gloves?
- A: The lot number is provided for traceability. Store the gloves away from sunlight, keep them dry, and ensure they are within the specified temperature limits. The gloves are made of raw material that is latex-free and suitable for use with foodstuffs.
The User Manual should be used with product-specific information.
User Instructions should be read before using.
INTENDED USE
- These gloves are intended to protect against certain chemicals, microorganisms, and radioactive contamination, where hand protection is needed.
- Foodstuff-approved gloves are marked with relevant food pictograms and comply with relevant EU Regulations. Gloves should be used only according to their intended purpose.
PRECAUTIONS OF USE
WARNINGS AND PRECAUTIONS OF USE
This information does not reflect the actual duration of protection in the workplace and the differentiation between mixtures and pure chemicals and other factors influencing the performance such as temperature, abrasion, degradation etc. The chemical resistance has been assessed under laboratory conditions from samples taken from the palm only (except in cases where the glove is equal to or over 400 mm – where the cuff is tested also) and relates only to the chemical tested. It can be different if the chemicals used in a mixture. It is recommended to check that the gloves are suitable for the intended use because the conditions at the workplace may differ from the type test depending on temperature, abrasion, and degradation. When used, protective gloves may provide less resistance to a dangerous chemical due to changes in physical properties.
Movements, snagging, rubbing, degradation caused by chemical contact, etc., may reduce the actual use time significantly. For corrosive chemicals, degradation can be the most important factor to consider in the selection of chemical-resistant gloves. Degradation levels (EN ISO 374-4:2019) indicate the change in puncture resistance of the gloves after exposure to the challenge chemical. The penetration resistance has been assessed under laboratory conditions and relates only to the tested specimens. These gloves do not protect against mechanical risks and ionizing radiation.
PRODUCT INSTRUCTION FOR USE
Before use, after donning, and during use inspect the gloves for any defect or imperfections and discontinue use immediately if signs of tearing, swelling or degradation, or any damage appear. Dry hand before donning. Ensure chemicals or residuals cannot enter through the cuff. Always select the correct size glove for your hand. For donning, hold the glove by the bead with one hand. Align the glove thumb with your other hand thumb and slide your hand into the glove, one finger into each glove finger.
Pull by the glove palm to get a good fit. Don the other glove by the same procedure. Doffing, hold glove bead and pull toward the finger until the glove come off. For Single Use only. If re-used, the risk of contamination and infection increases due to improper cleaning processes; and increased risk of holes and tear during re-use due to weakening of gloves by cleaning processes. Poorly-fitting gloves will greatly reduce dexterity and cause fatigue. Using the wrong glove size leads to inadequate hand protection. When an indication for hand hygiene precedes a contact that also requires glove usage, hand rubbing or hand washing should be performed before donning gloves and after removing gloves.
INGREDIENTS/HAZARDOUS COMPONENTS
Components used in glove manufacturing may cause allergic reactions in some users. If allergic reactions occur, seek medical advice immediately. Where relevant, a list of substances contained in the glove that are known to cause allergies, per listed in Annex G of EN ISO 21420:2020, shall be supplied on request.
STORAGE
Store in a cool and dry place in its original package. Recommended to store at room temperature prevailing in respective countries. Opened boxes should be kept away from fluorescent and sunlight.
Keep the gloves away from ozone, heating devices, and the source of the fire. Gloves are packed in a dispenser box suitable for transport. Keep the gloves in the box when not in use. The shelf life for products stored as recommended is mentioned on each package. Service life cannot be specified and depends on the application and responsibility of the user to determine the suitability of the glove for its intended use.
Further information can be obtained from the manufacturer, please contact Granberg AS.
EXPLANATION OF SYMBOLS
EXPLANATION OF SYMBOLS AND PICTOGRAMS USED
Protective gloves against dangerous chemicals and microorganisms – Part 1: Terminology and performance requirements for chemical risks. EN ISO 374-1:2016+A1:2018. Definition of breakthrough time through the glove palm (1 μg/cm2/min). Type A > level 2 for 6 chemicals, Type B > level 2 for 3 chemicals, Type C > level 1 for 1 chemical (no code under pictogram).
- A: Methanol
- B: Acetone
- C: Acetonitrile
- D: Dichloromethane
- E: Carbon disulphide
- F: Toluene
- G: Diethylamine
- H: Tetrahydrofuran
- I: Ethyl acetate
- J: n-Heptane
- K: Sodium hydroxide 40%
- L: Sulphuric acid 96%
- M: Nitric acid 65%
- N: Acetic acid 99%
- O: Ammonium hydroxide 25%
- P: Hydrogen peroxide 30%
- S: Hydrofluoric acid 40%
- T: Formaldehyde 37%
Additional information on chemical resistance obtainable from manufacturer.
Permeation Performance Level| Measured Breakthrough Time
(minutes)
---|---
0| *
1| > 10
2| > 30
3| > 60
4| > 120
5| > 240
6| > 480
*Indicates that the glove falls below the minimum performance level as stated in EN ISO 374-1:2016+A1:2018 for the given individual hazard.
More Information
Available sizes
Available sizes
| XS| S| M| L| XL
---|---|---|---|---|---
5/6| 6/7| 7/8| 8/9| 9/10
EN ISO 374-1:2016+A1:2018
Type C
| Permeation
Performance Level
| Measured Breakthrough Time (minutes)| EN ISO 374-4:2019
Mean Degradation (%)
---|---|---|---
K| 40% Sodium Hydroxide| 6| > 480| -9.5
T| 37% Formaldehyde 37%| 4| > 120| 16.1
Latex free: yes.
This product is Category III Personal Protective Equipment as per Regulation (EU) 2016/425 and complies with standards: EN ISO 21420:2020, EN ISO 374-1:2016+A1:2018, EN ISO 374-5:2016, EN 421:2010 (excluding clause 4.3).
Notified Body responsible for EU Type Examination (Module B) and for quality assurance of the production process (Module D): SATRA Technology Europe Ltd. (NB No. 2777), Bracetown Business Park, Clonee, D15YN2P, Republic of Ireland.
EU Declaration of Conformity: www.granberg.no/search
Contacts
- Head office: GRANBERG AS, Bjoavegen 1442, 5584 Bjoa, Norway.
- Phone: +47 53 77 53 00
- E-mail: post@granberg.no
- Swedish office: GRANBERG SVERIGE AB, Schubergsvägen 20, 311 74 Falkenberg, Sweden.
- Phone: +46 (0)346 124 25
- E-mail: post@granberg-ab.se
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>