GRANBERG 116.591 Cut Resistant Gloves Protector User Manual
- June 2, 2024
- GRANBERG
Table of Contents
116.591 Cut Resistant Gloves Protector
User Manual
107.4330 Vibration-Reducing Work Gloves
EN 420:2003+A1:2009
1/A = minimum requirement
4/5/F = maximum requirement
X – not tested
The results are taken from the palm area of the gloves.
The protection level increases with performance class.
Tested and approved in accordance to EN ISO 10819:2013
‘M’ Spectrum T(M) : 0.707 (Pass)
‘H’ Spectrum T(M) : 0.534 (Pass)
This product is classed as Category II Personal Protective Equipment (PPE)
according to PPE
Regulation (EU) 2016/425 and as retained in UK Law and amened and has been
shown to comply with this Regulation through the Harmonized Standards and
Designated Standards EN 420:2003+A1:2009, EN 388:2016+A1:2018.
Notified Body responsible for EU Type Examination (Module B):
Name: CENTRALNY INSTYTUT OCHRONY PRACY – PANSTWOWY INSTYTUT
BADAWCZY (CIOP-PIB).
Address: ul. Czerniakowska 16, 00-701 Warszawa, Poland
Notified Body number: 1437
Approved Body responsible for UKCA Type Examination:
Name: SATRA Technology Centre Ltd.
Address: Wyndham Way, Telford Way, Kettering, Northamptonshire NN16 8SD,
United Kingdom.
Approved Body number: 0321
Declaration of Conformity can be obtained from
https://www.granberg.no/catalog/107.4330
| Glove size | M | L | XL | 2XL | 3XL |
|---|---|---|---|---|---|
| EN 420 size | 8 | 9 | 10 | 11 | 12 |
Wear the products of suitable sizes to provide optimal level of protection and
maximum grip. User must only choose the glove fitting the size of her/his
hand.
Antivibration gloves reducing the risks and effect of Hand-Arm Vibration
Syndrome (HAVS). The gloves offer premium protection at high frequencies
combined with protection across a broad spectrum of frequencies. Gloves made
with Macroion Pro® material in the palm and with Spandex®/polyester on the
back.
Velcro closure.
Storage/Transport
The gloves are first packed in plastic bags which are subsequently packed in cardboard boxes for transport and storage. Granberg recommends storing unused gloves in original packaging. Prevent direct sunlight.
Maintenance/Cleaning
Both new and used gloves should be inspected before use, and before putting
them on to make sure that there is no damage to them. If in doubt, discard the
gloves and select a new pair. Leaving the gloves in a contaminated condition
may cause a deterioration of quality. Cleaning or disinfecting the gloves may
also negatively affect quality. The performance characteristics of gloves
that have been worn or cleaned/disinfected/laundered may differ from the
performance levels declared.
Obsolescence: Service life depends on application and maintenance and
cannot be specified. It is the responsibility of the user to ascertain the
suitability of the gloves for the user’s tasks.
Donning/Doffing: Select the right size glove for your hand. Hold the
glove by the cuff with one hand. Align the glove thumb with your other hand
thumb and slide your hand into the glove, one finger into each finger. Pull
by the glove cuff and align fingers into the right position. Use the same
procedure for the other hand. If gloves are not contaminated, pull by the
fingertips to doff the gloves. If gloves are contaminated, hold the glove cuff
and pull toward the finger until the gloves come off.
Please note: Inspect the gloves for damage before use. The gloves shall
not be worn when there is a risk of entanglement with moving parts of
machines. Gloves meeting the requirement for resistance to puncture may not
be suitable for protection against sharply pointed objects such as hypodermic
needles.
Gloves containing latex may cause allergic reactions in case of
hypersensitivity to latex. Seek medical advice if applicable. None of the raw
materials used in glove, or process of manufacturing it, are known to be
harmful to the user. These gloves are intended to protect hands in working
environments in accordance with EN 388:2016
+A1:2018, EN ISO 10819:2013 and EN 420:2003+A1:2009. It is the responsibility
of the user to evaluate and determine risks based on the intended application.
The gloves should only be used for applications declared suitable by the
manufacturer. Risk should be evaluated keeping in mind the protection levels
and the harmonized standards on which gloves are tested. The results of the
tests should help in glove selection, however it must be understood that
actual conditions of use cannot be simulated and it is the responsibility of
the user, not the manufacturer, to determine glove suitability to the intended
use.
Further information may be obtained from manufacturer.
User Manual issue date: 23.11.2022
Granberg AS, Bjoavegen 1442, NO-5584 Bjoa, NORWAY
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>