GRANBERG 113.1020 Working Gloves User Manual
- October 30, 2023
- GRANBERG
Table of Contents
GRANBERG 113.1020 Working Gloves
Product Information
The product is a pair of gloves with the following details:
- Article Number: 113.1020
- Category: II
- Size: 7/S, 8/M, 9/L, 10/XL, 11/2XL
- EN 420:2003+A1:2009
- Packaging: 12 pairs per pack
Product Usage Instructions
To ensure optimal protection and maximum grip, it is important to wear gloves that fit properly. Follow the steps below to choose the right glove size:
- Refer to the EN 420 size chart to determine your glove size based on your hand measurement.
- Choose the glove size that corresponds to your EN 420 size.
- Put on the gloves and adjust them to ensure a comfortable fit.
Note:
- The user must only choose the glove fitting the size of their hand.
- The user manual issue date is 22.06.2022.
Manufacturer details:
- Granberg AS
- Bjoavegen 1442
- NO-5584 Bjoa
- Norway
Assembly working gloves made of soft goatskin. Unlined. Storage/Transport: The gloves are first packed in plastic bags which are subsequently packed in cardboard boxes for transport and storage. Granberg recommends storing unused gloves in original packaging. Prevent direct sunlight.
Maintenance/Cleaning
Leaving the gloves in a contaminated condition may cause a deterioration of quality. Cleaning or disinfecting the gloves may also negatively affect quality. The performance characteristics of gloves that have been worn or cleaned/disinfected/laundered may differ from the performance levels declared. Obsolescence: Service life depends on application and maintenance and cannot be specified. It is the responsibility of the user to ascertain the suitability of the gloves for the user’s task or tasks.
Please note : Inspect the gloves for damage before use. The gloves shall not be worn when there is a risk of entanglement with moving parts of machines. Gloves meeting the requirement for resistance to puncture may not be suitable for protection against sharply pointed objects such as hypodermic needles. Gloves containing latex may cause allergic reactions in case of hypersensitivity to latex. Seek medical advice if applicable. None of the raw materials used in glove, or process of manufacturing it, are known to be harmful to the user. These gloves are intended to protect hands in working environment in accordance with EN 388:2016+A1:2018 and EN 420:2003+A1:2009. It is the responsibility of the user to evaluate and determine risks based on the intended application. The gloves should only be used for applications declared suitable by the manufacturer. Risk should be evaluated keeping in mind the protection levels and the harmonized standards on which gloves are tested. The results of the tests should help in glove selection, however it must be understood that actual conditions of use cannot be simulated and it is the responsibility of the user, not the manufacturer, to determine glove suitability to the intended use. Further information may be obtained from manufacturer.
1/A = minimum requirement
4/5/F = maximum requirement
X – not tested
The results are taken from the palm area of the gloves.
The protection level increases with performance class.
This product is classed as Category II Personal Protective Equipment (PPE)
according to PPE Regulation (EU) 2016/425 and has been shown to comply with
this Regulation through the Harmonised Standards EN 420:2003+A1:2009, EN
388:2016+A1:2018.
Notified Body responsible for certification (Module B):
Name: SATRA Technology Europe Ltd.
Address: Bracetown Business Park, Clonee, Dublin D15 YN2P, Republic of
Ireland.
Notified Body No: 2777
Declaration of Conformity can be obtained from
https://www.granberg.no/catalog/113.1020
Wear the products of suitable sizes to provide optimal level of protection and maximum grip. User must only choose the glove fitting the size of her/his hand.
User Manual issue date: 22.06.2022
Granberg AS, Bjoavegen 1442, NO-5584 Bjoa, NORWAY
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>