MeTra 99-7421 Dash Kit Installation Guide

July 27, 2024
Metra

INSTALLATION INSTRUCTIONS FOR PART 99-7421
APPLICATIONS
Nissan Maxima
2007-2008
(without navigation)

MeTra 99-7421 Dash Kit

99-7421

99-7421 Dash Kit

KIT FEATURES

  • DIN Mount Radio Provision with Pocket
  • ISO Mount Radio Provision with Pocket
  • Double DIN Mount Radio Provision
  • Stacked ISO Units Provision

KIT COMPONENTS
A) Radio Housing
B) Radio Housing Trimplate
C) Radio Housing Brackets
D) Double DIN Trim Plate
E) (4) #8 3/8” Screws
F) ISO Brackets

MeTra 99-7421 Dash Kit - Fig 1

WIRING AND ANTENNA CONNECTIONS (Sold Separately) Harness:

  • 70-7552 – Nissan harness 2007-up

  • NIRD-01 – Nissan display and Bluetooth retention harness 2007-08
    Antenna Adapter:

  • 40-NI12 – Nissan antenna adapter 2007-up

TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
Phillips Screwdriver • Torx Driver • Socket Set

MeTra 99-7421 Dash Kit - Fig 2

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

DASH DISASSEMBLY

NISSAN MAXIMA 2007-2008

  1. Disconnect the negative battery terminal to prevent an accidental short circuit.
  2. Unlock the collar bellow shifter knob by turning collar counter clockwise and slide collar down. Using a small screwdriver or hook tool remove the spring clip to release and remove the shifter knob. (Figure A)MeTra 99-7421 Dash Kit - Fig 3
  3. Unclip center console trim panel around shifter including a/c controls. Unplug and remove center console trim panel. (Figure B)MeTra 99-7421 Dash Kit - Fig 4
  4. Remove (2) Phillips screws facing upward on bottom of trim panel surrounding the radio including the a/c vents. (Figure C)MeTra 99-7421 Dash Kit - Fig 5
  5. Unclip and remove the trim panel surrounding the radio including the a/c vents. (Figure D)MeTra 99-7421 Dash Kit - Fig 6
  6. Remove (4) Phillips screws securing the radio/display assembly. Unplug and remove the radio/display assembly. (Figure E)MeTra 99-7421 Dash Kit - Fig 7
  7. Remove (2) Phillips screws and (5) orx screws (per side) securing the factory brackets to the radio/display assembly. (Retain screws, factory brackets, 2 displays and A/C amplifier for use during kit assembly.) (Figure F)
    MeTra 99-7421 Dash Kit - Fig 8

KIT ASSEMBLY

DIN RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.

  1. Attach the (2) radio housing brackets to the radio housing using the (4) #8 3/8” screws supplied with the kit. (Figure A)MeTra 99-7421 Dash Kit - Fig 9
  2. Secure the 2 displays and A/C amplifier into the radio housing/bracket assembly using the factory hardware. (Figure B)MeTra 99-7421 Dash Kit - Fig 10
  3. Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure C)MeTra 99-7421 Dash Kit - Fig 12
  4. Slide the aftermarket radio into the cage until it snaps into place. (Figure D)MeTra 99-7421 Dash Kit - Fig 11
  5. Attach the radio housing trim plate supplied with the kit. (Figure D)

ISO RADIO PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.

  1. Attach the (2) radio housing brackets to the radio housing using the (4) #8 3/8” screws supplied with the kit. (Figure A)MeTra 99-7421 Dash Kit - Fig 13
  2. Secure the 2 displays and A/C amplifier into the radio housing/bracket assembly using the factory hardware. (Figure B)MeTra 99-7421 Dash Kit - Fig 14
  3. Mount the ISO Brackets to the aftermarket radio using the screws supplied with the radio. (Figure C)MeTra 99-7421 Dash Kit - Fig 16
  4. Slide aftermarket radio into the radio housing until the side clips engage. (Figure D)MeTra 99-7421 Dash Kit - Fig 15
  5. Attach the radio housing trim plate supplied with the kit. (Figure D)

DOUBLE DIN MOUNT RADIO PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.

  1. Re-attach the factory brackets to the 2 displays and A/C amplifier using the factory hardware. (Figure A)MeTra 99-7421 Dash Kit - Fig 17
  2. Slide the Double DIN radio into the factory brackets and secure the unit to the brackets using the screws supplied with the radio. (Figure B)MeTra 99-7421 Dash Kit - Fig 18
  3. Place the Double DIN trim plate over the face of the aftermarket radio. (Figure B)

MeTra 99-7421 Dash Kit - Fig 20

STACKED ISO UNITS PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.

  1. Re-attach the factory brackets to the 2 displays and A/C amplifier using the factory hardware. (Figure A)MeTra 99-7421 Dash Kit - Fig 19
  2. Slide the stacked ISO mount units into the factory brackets and secure the units to the brackets using the screws supplied with the units. (Figure B)MeTra 99-7421 Dash Kit - Fig 18
  3. Place the Double DIN trim plate over the face of the ISO mount units. (Figure B)

FINAL ASSEMBLY

(A) Strip wire ends back 1/2″
B) Twist ends together
C) Solder
D) Tape

  1. Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
  2. Re-connect the negative battery terminal and test the unit for proper operation.
  3. Reassemble radio and dash assemblies in reverse order of disassembly.

FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE
12V Ignition / Acc . . . . . . . . . . Red
12V Batt / Memory . . . . . . . . . Yellow
Ground . . . . . . . . . . . . . . . . . . Black*
Power Antenna . . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground . . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black

*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.

1-800-221-0932
www.metraonline.com
REV. 06/25/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST99-7421

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals