PNI P05 A Parking Aid system User Manual
- July 25, 2024
- PNI
Table of Contents
PNI Escort P05 A
Parking aid system
User manual
P05 A Parking Aid system
The parking assist system consists of 4 ultrasonic sensors, a command unit, a
rear-view camera and a rearview mirror with LCD screen.
The system detects the distance between the car and the obstacles with the
ultrasonic sensors installed in the rear bar.
The obstacle image behind the car will be displayed on the screen. With sound
alarm, the safe area is detected.
Main features:
- Rear view mirror with color LCD display to display the rear image
- Numeric distance display
- Alarm sound
- Two or four sensors can be mounted
Technical specifications:
- Supply voltage: 10.5 – 16 V cc
- Consumption: 20 ~ 200 mA
- Detection distance: 0.3 – 2.5 m
- Frequency: 40 KHz
- Working temperature: -26 ~ +80°C
Installation of sensors:
Correct positioning of sensors:
Connection diagram:
Alarm mode:
| Stages | Distance | Awareness | Display | Alarm sound | Color |
|---|---|---|---|---|---|
| 1 | 2.5 – 1.6m | Safe | 2.5 – 1.6m | Silence | Green |
| 2 | 1.5 – 1.0m | Safe | 1.5 – 1.0m | Bi … bi … bi | Yellow |
| 3 | 0.9 – 0.5m | Alarm | 0.9 – 0.5m | Bi bi bi | Red |
| 4 | <0.4m | Danger | <0.4m | Biiii… | Red |
Note:
- The 3M adhesive tape can not be used repeatedly. The gluing effect will be complete after 48 hours.
- Sensor wires should not be cut or prolonged.
- Mounting holes are made in the spoiler to install the sensors.
- Please check the correct direction of the sensors.
- Before installation, check the camera’s field of view after feeding it.
Installation and testing:
-
After installing the sensors, arrange them in the correct direction. Arrange the threads in order.
-
Plug the red lead from the control unit into the “+” light of the turn signal lamp, and the black lead at “-”.
Connect the red camera cable back to the “+” of the muzzle lamp. The screen must be connected to the ACC feed, the table must be connected to the straightening thread. (please study the connection diagram). -
Connect the screen to the control unit. Connect the “Vout” output on the control unit to the “Video 2” input on the screen.
-
Put the switch in the march to test if the screen is working. In this situation, on the screen in the mirror you should have the image behind the car, you will have a white dot at the bottom of the image. This indicates that the system is under test.
Test:
a. If the rear image does not appear on the screen, please check that the
polarity of the power supply is the correct one if the cables are connected
correctly and if the voltage is greater than 10.5V. Check if the screen
connector is well connected.
b. If the distance displayed on the screen is not in line with reality or is
displayed at 0.0, or a steady sound is heard, please unplug the system, and
try again to insert the gear lever into the march. If problems can not be
solved, the unit is damaged and needs to be changed.
c. When testing the sensors, if the screen will sound continuously or display
0.0, please check that some parts of the machine or other objects are within
the range of the sensors, if the sensor is incorrectly mounted in the hole, or
if the sensor is under the influence strong sources of interference (such as
exhaust pipes, other wires).
d. If a number is displayed on the screen but there is no obstacle in front of
the sensors, make sure that the sensors are wrongly facing down, please check
the position and direction of the sensors. The sensors must be mounted
horizontally. Sensors can detect (if incorrectly mounted) the registration
number, the spare wheel or the rear spoiler.
e. If problems can not be solved after tests, sensors may be considered
defective or do not match the control unit. The whole system should be
replaced.
f. If the image is in gradient or overturned, please check the connection of
the camera.
g. For abnormal display with stripes or tilted lines, please check the
compatibility between the screen and the camera.
h. The screen can be interchanged, but the sensors and the control unit are
compatible one by one.
i. For safety reasons, the screen will only show 0.0, instead of 0.3-0.1, when
it detects something within 0.0-0.4 m depending on the software. In this
situation, the driver must stop immediately. When the distance is 0.5 m, the
alarm sound will sound and will last for 1 second. Please be careful during
maneuvers.
Notes
- Be aware of the size of the sensor mounting hole
- During installation of the system, the engine of the car must be switched off
- System performance can be altered in the following cases: heavy rain, paved road, uneven road, vegetation, extremely hot weather, wet or cold, snow, mud or ice on sensors
- System operation may be affected by the presence of other ultrasonic waves, such as a 24 / 12V converter
- The sensors should not be mounted too tightly or too lightly
- The metal bumper can affect the performance of the system
- Do not position the control unit near the exhaust pipe or other wires
- Test the system to make sure it works properly
- This system is designed to assist the driver in parking. The manufacturer does not take responsibility for accidents after installation.
We recommend installing the system at an authorized service center.
The supplier does not assume responsibility for defects caused by incorrect
installation.
EU Simplified Declaration of Conformity
SC ONLINESHOP SRL declares that Parking aid system PNI Escort P05 A complies
with the Directive EMC 2014/30/EU. The full text of the EU declaration of
conformity is available at the following Internet address:
https://www.mypni.eu/products/4940/download/certifications
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>