peerless-AV PT670 Paramount Universal Tilt Wall Mount Instruction Manual

: July 25, 2024
: Peerless-AV

Table of Contents

peerless-AV PT670 Paramount Universal Tilt Wall Mount
Product Information
Product Usage Instructions
Symbols
Tools Needed for Assembly
Parts List
Installation
Warranty
Contact Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

peerless-AV PT670 Paramount Universal Tilt Wall Mount

Product Information

Product Specifications

Model: PT670
Adjustable Height: 37 – 80 inches (94 – 203 cm)
Weight Capacity: 165 lb (75 kg) MAX

Product Usage Instructions

Assembly Instructions:
Before starting the assembly, ensure you have all the parts listed in the Parts List section of the user manual.

Tools Needed:

3/16 inch (4.5mm) screwdriver
3/8 inch (10mm) wrench

Screws Tightening Guidelines:
To properly tighten screws, follow these steps:

Tighten the screws until the head makes contact with the surface.
Then tighten the screws another 1/2 turn.
Do not over-tighten the screws to avoid damage.

Installation Instructions:

Verify that wood studs on the wall are at least 2 x 4 nominal size.
Do not install over gypsum board thicker than 5/8 inch.
Use a stud finder to locate and mark stud center lines on the wall.
Level the wall plate and mark the mounting holes on the stud center lines.

FAQ

Q: How do I know if I have all the necessary parts for assembly?
A: Refer to the Parts List section in the manual to ensure you have all the required components before starting assembly.
Q: What is the recommended weight capacity for this product?
A: The maximum weight capacity for the PT670 model is 165 lb (75 kg).

WARNING
This product is designed to be installed on wood studs, solid concrete, or cinder block walls. Hardware is included for wood studs, solid concrete, and cinder block installation. Before installing make sure the supporting surface will support the combined load of the equipment and hardware. Screws must be tightly secured. Do not overtighten screws or damage can occur and the product may fail. Never exceed the Maximum Load Capacity. Always use an assistant or mechanical lifting equipment to safely lift and position equipment. This product is intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury. Be careful not to pinch your fingers when operating the mount. For support please call customer care at 1-800-865-2112.

Symbols

WARNING
Skip to step.
Screws must get at least three full turns and fit snugly.
Do not overtighten screws.

Tools Needed for Assembly

To properly tighten screws:
Tighten until the screw head makes contact, then tighten another 1/2 turn. Do not overtighten screws.

Parts List

Parts (Before beginning, make sure you have all the parts shown below).

Parts List Description

|

Qty

---|---
A| wall plate| 1
B| left adaptor bracket| 1
C| right adaptor bracket| 1
D| bubble level| 1
E| 5mm allen wrench| 1
W- B| concrete anchor| 6
W- A| wood screw| 6
M-A| M5 x 14mm| 4
M-B| M6 x 14mm| 4
M-C| M6 x 30mm| 4
M-D| M8 x 30mm| 4
M-E| M8 x 50mm| 4
M-G| small spacer| 8
M-H| large spacer| 8
M-F| multi washer| 4
W- C| washer| 6

Installation

Wood stud wall. Concrete/Cinder block.
- a. WARNING
  When installing Peerless wall mounts on a wood stud wall covered with gypsum board (drywall), verify that the wood studs are a minimum of 2″ x 4″ nominal size. Do not install over gypsum board thicker than 5/8″.
- 1a-1 Use a stud finder to locate and mark stud center lines.
- 1a-2 Level wallplate. Mark mounting holes on stud center lines.
- 1a-3 Drill mounting holes into the supporting surface (2.2″ (55mm) minimum depth required).
  The mounting hole must center on the stud.
- 1a-4 Level wallplate. Install using the wood screws provided.
- 1b. WARNING
  When installing Peerless wall mounts on a concrete wall, the wall must be at least 8″ thick with a minimum compressive strength of 2000 psi. When installing Peerless wall mounts on a cinder block wall, the cinder blocks must meet ASTM C-90 specifications and have a minimum nominal width of 8″. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1″ (25 mm) minimum from the side of the block. It is suggested that a standard electric drill on a slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity. Never attach concrete expansion anchors to concrete or cinder block covered with plaster, drywall, or other finishing material.
- 1b-1 Level wallplate. Mark mounting holes.
- 1b-2 Drill mounting holes into the supporting surface (2.4″ (60mm) minimum depth required).
- Do not drill into mortar joints.
- 1b-3 Insert anchor flush to concrete.
- 1b-4 Level wallplate. Install using concrete anchors and wood screws provided.
1. Optional.
Height adjustment: Tighten or loosen.