MeTra 107-GM4B Double Din Installation Kit Instruction Manual

July 23, 2024
Metra

MeTra 107-GM4B Double Din Installation Kit Instruction Manual
MeTra 107-GM4B Double Din Installation Kit

Chevrolet Silverado 1500 (†)GMC Sierra 1500 (†)2019-Up

Chevrolet Silvered o2500/3500 (†),GMC Sierra 2500/3500 (†)2020-Up
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle specific applications (†) Models with a 2 knob 8-inch screen radio, RPO code IOS or IOT.
The RPO code can be found in the Vehicle Certification Label located on the inside of the driver’s door opening.
A mobile device with a QR scanner must be used to decipher the code.

KIT FEATURES

  • Designed specifically for the Pioneer DMH-C2550NEX and DMH-C2500NEX radios
  • Painted scratch resistant matte black to match the factory finish

KIT COMPONENTS

  • A) Display screen housing

  • B) Display screen brackets

  • C) Blank-out panel

WIRING & ANTENNA CONNECTIONS

Wiring Harness : AXTC-LN30 (‡) (sold separately)
Antenna Adaptor: 40-EU55 (sold separately)
RGB Extension Cable: Pioneer part # CD-RGB150E (not sold by Tetra)

(‡) Non-amplified models only

TOOLS REQUIRED

  • Panel removal tool
  • Phillips screwdriver
  • 9/32” socket wrench
  • T-15 Torx screwdriver

Attention! Let the vehicle sit with the key out of the ignition for a few minutes before removing the factory radio. When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition.

DASH DISASSEMBLY

For models with a full center console:

  1. Unclip the screw cover from the driver’s side of the centre console, then remove (1) 9/32” screw exposed. (Figure A)

  2. Starting from the rear, unclip and remove the centre console trim panel from each side of the centre console. (Figure B)

  3. Starting from the rear, uncle and remove the cup holder panel. (Figure C) Continued on the next page.

  4. Unclip and remove the lower trim panel. (Figure D)
    Assembly Instruction

  5. Unclip and remove the trim panel surrounding the radio display. (Figure E)
    Assembly Instruction

  6. Remove (6) 9/32” screws securing the climate and radio control panel, then unplug and remove. (Figure F)
    Continue to Kit Preparation
    Assembly Instruction

For models without a full center console:

  1. Unclip and remove the lower trim panel. (Figure A)
    Assembly Instruction

  2. Unclip and remove the trim panel surrounding the radio display. (Figure B)
    Assembly Instruction

  3. Remove (6) 9/32” screws securing the climate and radio control panel, then unplug and remove. (Figure C) Continue to Kit Preparation
    Assembly Instruction

KIT PREPARATION

From the factory climate and radio control panel:

  1. Remove (10) T-15 Torx screws securing the cover from the back of the radio. (Figure A)
    Kit Preparation

  2. Slightly lift up the bottom of the cover to access the ribbon cable securing the radio display to the radio controls.
    Unplug the cable, then remove the display.

  3. Remove (4) T-15 Torx screws securing the radio controls, then remove. (Figure B)
    Kit Preparation

  4. Place the blank out panel into the panel, then secure using the factory screws. (Figure C)
    Continue to Kit Assembly
    Kit Preparation

KIT ASSEMBLY

  1. Secure the display screen to the display screen brackets using (6) screws supplied with the radio. ( Figure A)
    Note: Reference the installation manual provided with the radio for which hardware to use. The display screen and radio chassis use two different types of screws.
    Kit Assembly

  2. Find a suitable location for the radio chassis. Route the RGB extension cable from the radio chassis to the display screen, then connect it to the display screen.

  3. Place the display screen assembly into the display screen housing, then secure the entire assembly to the factory radio panel using the factory screws. (Figures B, C)
    Kit Assembly
    Kit Assembly

  4. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio assembly. Meta recommends using the proper mating adapter from Meta and/or Axes. Test the radio for proper operation.
    Note : Temporarily plug the climate control panel back in during testing to avoid vehicle errors codes.

  5. Reassemble the dash in reverse order of disassembly to complete the installation.

If you are having difficulties with the installation of this product, contact our Tech Support line either by phone at 386-257-1187, or email at techsupport @metra-autosound.com. Before doing so, look over the instruction booklet a second time and ensure that the installation was performed exactly as the instruction booklet is stated. Have the vehicle apart and ready to perform troubleshooting steps before contacting Meta/Axes Tech Support.
QR Code

Installer InstituteKNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognised and respected mobile electronics school in our industry.
Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

Mobile electronics certification programMetra recommends MECP certified technicians

Company logo

Documents / Resources

| MeTra 107-GM4B Double Din Installation Kit [pdf] Instruction Manual
107-GM4B Double Din Installation Kit, 107-GM4B, Double Din Installation Kit, Din Installation Kit
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals