superbrightleds com DS-RT09 Addressable RGB LED Controller and Remote User Manual

superbrightleds com DS-RT09 Addressable RGB LED Controller and Remote

Specifications

• Product: Addressable RGB LED Controller and Remote
• Model: DS-SC (with DS-RT09)
• Power Supply: CR2032 Battery
• Strip Length: Up to 1,024 pixels
• RGB Order Options: RGB, RBG, GRB, GBR, BRG, BGR
• IC Type Options: TM1803, TM1809, TM1804, TM1812, UCS1903, UCS1909, UCS1912, UCS2903, UCS2909, UCS2912, WS2811, WS2812, and more

Product Usage Instructions

Remote(s) must be paired as part of the installation process. Each controller can be paired to up to ten (10) remotes.

• To pair a remote:

  • Press the match button on the controller.
  • Immediately press the on/off button on the remote.
  • The indicator light on the controller will flash slowly while
    attempting to pair, then flash five times rapidly to indicate
    successful pairing.

• To unpair a remote:

  • Hold the match button for five seconds.
  • The indicator light on the controller will flash five times
    rapidly to indicate successful unpairing.

• Press the function button (*).

• Enter the number of pixels using the number buttons.

• Press the function (*) button again.

• Note: Numbers lower than 100 will need a zero (0) entered before the number.

• Press the function button (*).

• Enter the one-digit code corresponding with the correct RGB order using the number pad.

• Press the function (*) button again.

• Press the function button (*).

• Enter the two-digit code corresponding with the correct IC type using the number pad.

• Press the function (*) button again.

• Consult the provided list for the codes of each IC type.

FAQ

• Q: How many remotes can be paired with each controller?
• A: Each controller can be paired with up to ten (10) remotes.
• Q: How do I adjust the speed of preprogrammed modes?
• A: Press the speed buttons to adjust the speed. Hold the upper speed button for two seconds to select the fastest speed and hold the lower speed button for two seconds to select the slowest speed.
• Q: How do I save settings using scene buttons?
• A: Each scene button can save one setting. Press and hold a scene button for two seconds to save settings. Press the scene button after saving settings to recall those settings.

Safety and Notes

• The product should be installed and serviced under applicable national, state, and local building and electrical codes.
• To reduce the risk of electric shock, ensure that the main power source and circuit breakers are switched off before performing any installation or wiring procedures.

Battery Safety

• Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate them.
• Even used batteries may cause severe injury or death.
• Call a local poison control center for treatment information.
• Non-rechargeable batteries are not to be recharged.
• Do not force discharge, recharge, disassemble, heat above (manufacturer’s specified temperature rating) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
• Ensure the batteries are installed correctly according to polarity (+ and -).
• Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
• Remove and immediately recycle or dispose of batteries from equipment not used for an extended time according to local regulations.
• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

WARNING

• INGESTION HAZARD: This product contains a button cell or coin battery.
• DEATH or serious injury can occur if ingested.
• A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
• KEEP new and used batteries OUT OF REACH of CHILDREN
• Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.

Remote Layout and Functions

Mode

• Once setup is complete (see page 2) press to cycle between preprogrammed modes. Hold the upper mode (mode plus) button for two seconds to run the mode cycle demo setting.
• Hold the lower mode (mode minus) button for two seconds to return to and run mode 1.

Speed

• Press to adjust the speed of the selected preprogrammed mode. Hold the upper speed (speed plus) button for two seconds to select the fastest speed.
• Hold the lower speed (speed minus) button for two seconds to select the slowest speed.

Brightness

• Press to adjust brightness in ten percent increments.
• Hold for continuous 256 level adjustment.

RGB

• Press to adjust in ten-percent increments. Hold for continuous 256 level adjustment.

White

• Press to turn white (RGB mix) on/off. Hold for continuous 256 level adjustment.

Scene

• Each scene button can save one setting. The setting is saved by holding the scene button for two seconds.
• Press the scene button after saving settings to recall those settings.

Pairing Remote(s)

REMOTE(S) MUST BE PAIRED AS PART OF THE INSTALLATION PROCESS AND DO NOT COME PRE-PAIRED. EACH CONTROLLER CAN BE PAIRED TO UP TO TEN (10) REMOTES.

To pair a remote, press the match button on the controller, then immediately press the on/off button on the remote. The indicator light on controller will flash slowly while attempting to pair, then five times rapidly to indicate successful pairing. To unpair a remote, hold the match button for five seconds. The indicator light on the controller will flash five times rapidly to indicate successful unpairing.

Important: Read all instructions before installation.

Setting Adjustment

Strip Length (Pixel Number) Setting

• Strip length, or pixel number, can be set up to 1,024 pixels.
• Begin by pressing the function button (), then entering the number of pixels with the number buttons, and then pressing the function () button again.
• Note: Numbers lower than 100 will need a zero (0) entered in before the number.

RGB Order

• RGB order can be set by pressing the function button (), then entering the one-digit code corresponding with the correct RGB order using with the number pad, and then pressing the function () button again.

IC Type Setting
IC type can be set by pressing the function button (), then entering the two- digit code corresponding with the correct IC type using the number pad, and then pressing the function () button again. Consult the list below for the code for each IC type.

UCS2912, WS2811, WS2812
13| TM1829
14| TLS3001, TLS3002
15| GW6205
16| MBI6120
17| TM1814B(RGBW)
18| SK6812(RGBW)
19| UCS8904B(RGBW)
21| LPD6803, LPD1101, D705, UCS6909, UCS6912
22| LPD8803, LPD8806
23| WS2801, WS2803
24| P9813
25| SK9822
31| TM1914A

Preprogrammed Modes

• Once the remote is paired, hold the upper mode (mode plus) button for 2 seconds to unlock preprogrammed modes which can then be cycled through using the mode buttons on the remote.

Sectionally
9| 7 Color Multi Race Close + Open| 20| Red Float| 31| 7 Color Jump Sectionally
10| 7 Color Scan Close + Open| 21| Green Float| 32| 7 Color Strobe Sectionally
11| 7 Color Multi Scan Close + Open| 22| Blue Float| |

CONTACT

• 4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>