superbrightleds com KLE1017-U-200-50-12 Linear Explosion Proof Light User Manual

June 2, 2024
superbrightleds com

superbrightleds-com-KLE1017-U-200-50-12-Linear-Explosion-Proof-Light-
logo

superbrightleds com KLE1017-U-200-50-12 Linear Explosion Proof Light

Specifications

  • Model: KLE1017-U-200-50-12 (Yellow)
  • Operating Temperature: IP66
  • IP Rating: IP66
  • Fixture Weight: 39.5 lb (17.9 kg)

Product Usage Instructions

Safety and Notes
Read all instructions prior to installation. Check product label for specific electrical specifications related to installation. Improper installation will void warranty.

Wiring Diagram
Line – Black, Neutral – White, Ground – Green

Yoke Mount Installation (Included)

  1. Remove supply power.
  2. Select a suitable mounting location that can support the weight of the light.
  3. Use the mounting bracket and mark spots for mounting hardware to be installed.
  4. Drill holes and install hardware as needed.
  5. Securely mount the light.
  6. Connect wiring.
  7. Rotate the light to the desired angle and tighten adjustment screw.

Tools Required: Electric Drill, Expansion Bolt, Screwdriver, Flat Washer, Spring Washer, Hex Nut
Rev Date: V1 03/08/2023
4400 Earth City Expy, St. Louis, MO 63045
866-590-3533
superbrightleds.com

FAQ

  1. Q: What should I do if the light is not turning on after installation?
    A: Check the wiring connections and ensure power supply is connected properly. If issues persist, contact customer support for assistance.

  2. Q: Can this light be used in outdoor environments?
    A: Yes, this light has an IP66 rating, making it suitable for outdoor use as it is protected against dust and high-pressure water jets from any direction.

Safety and Notes

  • Product should be installed by a certified electrician in accordance with applicable national, state, and local building and electrical codes. Proper earth grounding is required.
  • To reduce the risk of electric shock, ensure that the main power source and circuit breakers are switched off before performing any installation or wiring procedures. If smoke is detected or a short circuit is present, switch off power immediately and notify relevant personnel.
  • Avoid looking directly into the light when illuminated.
  • Failure to properly support the fixture may result in damage or injury, for which the manufacturer does not assume responsibility. Check whether any accessories are correctly installed prior to installation.
  • If the light is damaged during shipping, do not install and contact customer service immediately.
  • To reduce the risk of ignition of hazardous atmospheres, disconnect the luminaire from the supply circuit before opening. keep tightly closed when in operation.

Specifications

Model KLE1017-U-200-50-12(x)
Operating Temperature -40°–149° F (-40°–65° C)
IP Rating IP66
Fixture Weight 39.5 lb (17.9 kg)

Check product label for specific electrical specifications related to installation. Improper installation will void warranty.

Wiring Diagram

superbrightleds-com-KLE1017-U-200-50-12-Linear-Explosion-Proof-
Light-\(1\)

Yoke Mount Installation (Included)

  1. Remove supply power.
  2. Select a suitable mounting location that can support the weight of the light.
  3. Use the mounting bracket and mark spots for mounting hardware to be installed.
  4. Drill holes and install hardware as needed.
  5. Securely mount light.
  6. Connect wiring.
  7. Rotate light to desired angle and tighten adjustment screw.

superbrightleds-com-KLE1017-U-200-50-12-Linear-Explosion-Proof-
Light-\(2\)

superbrightleds-com-KLE1017-U-200-50-12-Linear-Explosion-Proof-
Light-\(3\)

Rev Date: V1 03/08/2023
4400 Earth City Expy, St. Louis, MO 63045
866-590-3533
superbrightleds.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

superbrightleds com User Manuals

Related Manuals