midmark TP200 Left Cover Kit Installation Guide
- July 20, 2024
- Midmark
Table of Contents
Midmark TP200 Left Cover Kit
Specifications:
- Model: All
- Special Tools: None
- Part Number: 002-11040-00
- Revision: TP200 20-42-FO-00012 Rev A2 ECO088522
- Date: 003-10675-00 Rev. AA1 (3/05/2024) Style A
Product Usage Instructions
Left Cover Installation
Step 1: Turn the power switch to off. Unplug from power cord from the back of the delivery system.
Step 2: Release pressure from the pressure tank by holding the cloth on the tube and opening the valve.
Step 3: Move the toggle switch for water bottles to the middle position to release pressure from water bottles.
Step 4: Remove both water bottles from the dental delivery system.
Step 5: Remove fasteners (4). Slide out the motor from the delivery system.
Step 6: Remove the mat from the lid. Open the top lid by pulling the lever back and lifting lid all the way up.
Step 17: Install both water bottles onto the delivery system. Move the toggle switch to add pressure to the water bottle for use.
Step 18: Plug in the power cord to the back of the delivery system. Push the power switch to on.
FAQ
- Q: Do I need any special tools for installing the left cover?
- A: No, special tools are not required for the left cover installation process.
- Q: What should I do if I encounter difficulty in sliding the motor back into the delivery system?
- A: Ensure the slides are aligned properly and try gently pushing while maintaining alignment to slide the motor back in smoothly.
INSTALLATION
- Step 1:
- Turn the power switch to off. Unplug from power cord from the back of the delivery system.
- Step 2:
- Release pressure from the pressure tank by holding the cloth on the tube and opening the valve.
- Step 3:
- Move the toggle switch for water bottles to the middle position to release pressure from water bottles.
- Move the toggle switch for water bottles to the middle position to release pressure from water bottles.
- Step 4:
- Remove both water bottles from the dental delivery system.
- Step 5:
- Remove fasteners (4). Slide out the motor from the delivery system.
- Step 6:
- Remove the mat from the lid. Open the top lid by pulling the lever back and lifting the lid all the way up.
- Remove the mat from the lid. Open the top lid by pulling the lever back and lifting the lid all the way up.
- Step 7:
- Pull side storage out. Remove by pushing drawer slide clips on side storage towards the rear of the delivery system to release from the slide base and pull side storage out.
- Step 8:
- Remove screws (3) from left cover.
- Step 9:
- Remove screws (3) from left side plate. Remove screws (3) from left column.
- Remove screws (3) from left side plate. Remove screws (3) from left column.
- Step 10:
- Remove the left cover.
- Step 11:
- Install the left cover and ensure tabs are under the front covers as shown.
- Step 12:
- Secure the left cover with screws (3).
- Secure the left cover with screws (3).
- Step 13:
- Install screws (3) into left side plate. Install screws (3) into left column.
- Step 14:
- Line up slides and push side storage all the way in so slides engage. Pull side storage back out to ensure it is installed completely.
- Step 15:
- Slide the motor back into the delivery system. Secure with fasteners (4).
- Slide the motor back into the delivery system. Secure with fasteners (4).
- Step 16:
- Close lid and push down on the middle until a click is heard. Install mat onto lid.
- Step 17:
- Install both water bottles onto the delivery system. Move the toggle switch to add pressure to the water bottle for use
- Step 18:
- Plug in power cord to the back of the delivery system. Push the power switch to on.
- Plug in power cord to the back of the delivery system. Push the power switch to on.
© 2024 Midmark Corp.
60 Vista Drive Versailles, OH 45380 USA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>