Wayfair GS319R Freestanding Bathtub Installation Guide

Wayfair GS319R Freestanding Bathtub

Product Specifications

• Product Name: Freestanding Bathtub
• Model Number: GS319R

Product Usage Instructions

Installation Guide

• Follow the steps outlined in the installation guide provided with the product. Ensure to have all the necessary tools listed for installation.

Preparation

• Place a soft blanket or cloth on the floor surface to protect the bathtub during installation. Make sure the area is clean and level before proceeding.

Applying Adhesive

• Apply a generous bead of adhesive or waterproof silicone to the bottom of the freestanding bathtub to secure it in place.

Lifting and Installation

• It is recommended to have two people for lifting and installing the bathtub. Use adjustable channel wrench and lock pliers as needed during the installation process.

Frequently Asked Questions

Q: Do I need to use a specific type of silicone for installation?

A: It is recommended to use waterproof silicone for a secure installation of the freestanding bathtub.

Q: Can I install the bathtub on any type of floor surface?

A: Ensure that the floor surface is level and suitable for supporting the weight of the bathtub. Use a soft blanket or putty to provide additional support if needed.

TOOLS REQUIRED

TOOLS REQUIRED FOR INSTALLATION (NOT INCLUDED)

• CAUTION! TWO PERSON LIFT REQUIRED 2 PEOPLE ARE REQUIRED TO LIFT AND DURING ENTIRE INSTALLATION OF THIS PRODUCT

• Carefully, remove the tub from its crate/box.
  Important Note: The bathtub must be carried by a minimum of 2 adult people in an upside-down position only. Do not carry the bathtub by its panel.

• To avoid scratches or damage to the bathtub be sure to set it on cardboard with a soft blanket on top of the cardboard.

• Set your bathtub on two 4×4 pieces of lumber so you can have access from the bottom of the bathtub. Put a tray beneath the bathtub.

• Very Important! Before proceeding with installation, please check that the push scupper plug, drain, and integrated overflow are properly sealed and tightened.

• Push the scupper to plug into a close position and fill the bathtub with cold water above the overflow level to test for overflow leakage and drain leakage.

• Check for any leaks around the drain and pipe.

• NOTE: Due to surface tension, it is normal for a small amount of water to pool around the drain.

• If a leakage occurs please disassemble the drain line or overflow.

INSTALLATION WITH UNDERFLOOR ACCESS

1. Step 1 Clean, level, and prepare the floor for installation, Place the tub in the exact installed location on the floor trace the outline of the bathtub with a pencil, and mark the drain hole location on the floor.
   • Move the tub away so that the plumbing can be installed.
2. Step 2 Turn the bathtub upside down and set it on a non-abrasive mat, blanket, or cardboard to prevent any scratches on tub rim.
3. Step 3 Place a level across the bottom of the tub and adjust the tub feet leveler to touch the level. Then raise the leveler an additonal 1/8″ or 3/16″ so that the weight of the tub, water, and user are fully supported by the feet adjuster and not the tub walls.
   • Pop-up cover drain body rubber drain gasket tailpiece (provided by installer) floor drain pipe (provided by installer) trap (provided by installer) rubber drain gasket P-trap.
4. Step 4 Install a 1-1/2″ tailpiece along with the corresponding flanged washer and 1-1/2″ nut to the drain body.
5. Step 5 Measure and cut the tailpiece to the appropriate length to reach the trap adapter When seting the tub drain, insert the tailpiece with a 1-1/2″ slip joint and rubber washer into the trap adapter and tighten properly.
6. Step 6 Apply a generous bead of adhesive or waterproof silicone to the bottom of the tub and a bead of tub and tile caulk around the edge of the tub.
7. Step 7 Flip the tub over and carefully set the tub into position with tailpiece assembly to P-trap and connect to the drain.
8. Step 8 Fill the tub with water to the overflow and then drain the tub while inspecting the waste and overflow connection below the floor for any leaks. Access from below will be necessary for this step.
9. Step 9 With the tub now set in place, wipe off any excess tub or tile caulking, and adhesive where the tub meets the floor with wet cloth.
10. Step 10 DO NOT SHOWER or MOVE the tub after installation because it will take about 24 hours to get the silicone sealant to dry.

• Note: If installing on a concrete slab where no underfloor access or cannot move the drain.
• You may consider the following option.
• Optional flexible drain hose from plumbing hardware or a home improvement store may be used GETPRO will not supply this flexible hose).
• Connect one end attached to the bathtub drain and the other end needs to be attached to the floor drain by using a transition piece.
• An optional Island tub drain may also be used.
• Create a bridge from the bathtub drain to the floor drain with a certified plumber only because any wrong connection or loose connection will cause leaks.

INSTALLATION ON SLAB FLOOR (NO UNDERFLOOR ACCESS)

1. Step 1 Clean, level, and prepare the floor for installation, Place the tub in the exact installed location on the floor trace the outline of the bathtub with a pencil, and mark the drain hole location on the floor.
   • Move the tub away so that the plumbing can be installed.
2. Step 2 Turn the bathtub upside down and set it on a non-abrasive mat, blanket, or cardboard to prevent any scratches on the tub rim.
3. Step 3 Place a level across the bottom of the tub and adjust the tub feet leveler to touch the level. Then raise the leveler an additional 1/8″ or 3/16″so that the weight of the tub, water, and user are fully supported by the feet adjuster and not the tub walls.
4. Step 4 Measure the actual distance from the drain into the drain pipe on the floor and the drain pipe should extend approximately 1″ above the finish floor. Use a drain adapter (not provided) if necessary.
5. Step 5. Clean the surrounding of the drain pipe with cloth in preparation for setting the drain, the area should be dry and free of any debris. Apply a bead of clear silicon or plumber putty around the drain body and pass it through the drain hole, also apply plumber putty to the washer and slide it over the bottom of the drain body.
6. Step 6 Apply putty to fix the rubber sill gasket over the drain vent.
7. Step 7 Apply a generous bead of adhesive or waterproof silicone to the bottom of the tub and caulk around the edge of the tub.
8. Step 8 Flip the tub over and carefully set the tub into position with tailpiece assembly to the waste vent and connect it to the drain.
9. Step 9 With the tub now set in place, wipe off any excess tub or tile caulking, and adhesive where the tub meets the floor with wet cloth.
10. Step 10 DO NOT SHOWER or MOVE the tub after installation because it will take about 24 hours to get the silicone to dry.

IMPORTANT SAFETY RULES

ATTENTION! ALWAYS FOLLOW THESE PRECAUTIONS WHEN USING A BATHTUB

• Warning The bathtub must be installed and used as described in this manual
• Use caution when entering or exiting the bathtub
• Do not permit children or persons with infirmities to use the bathtub without supervision of an adult
• People using any medications or having adverse medical history must consult a physician before using the bathtub to avoid potential hyperthermia and possible drowning
• Water temperatures over 100°F may cause hyperthermia and/or other health problems. Check the water temperature and adjust it for your comfort
• Never use a bathtub while intoxicated, after taking meals, or any alcoholic beverages. Consuming alcoholic beverages before or during bathing will cause drowsiness and may result in hyperthermia, loss of consciousness, or even drowning
• If you are pregnant or you feel that you may be pregnant, consult your doctor before using the bathtub
• Never use any electrical devices such as a hair dryer, lamp, telephone, TV, radio, or others within 5 feet of the bathtub
• Do not overfill the bathtub before entering. Entering the bathtub when filled will cause overflow and slippery.

Care and Cleaning

• Most dirt will be washed off with mild soap and warm water.
• For tough spots, use liquid dishwashing soap or non-chlorine bleach.
• Do not use abrasive material such as steel wool or scouring pads to clean the acrylic surface.
• Always test the cleaning solution on a small area before using it on the entire surface.
• Do not allow cleaning to soak on the acrylic surface.
• Rinse thoroughly with water immediately and wipe dry with a soft cloth.

Repair and Maintenance

• Use liquid polish compounds such as Gel-Gloss Kitchen and Bath Polish(TM) to keep the original shine of the acrylic surface.
• Light scratches can be removed with a polishing compound for automobiles.
• For deeper scratches use wet sandpaper (1500 grit or higher). Always add water when sanding and lightly sand the area larger than the scratch in a circular motion to remove the scratches.
• Repeat until the scratch is removed. Use soft cloth and a small amount of polishing compound to restore shine. Repeat as needed until surface shine is restored.

IMPORTANT!

• DO NOT USE  Abrasive cleaners such as acid, ammonia, bleach, and similar solutions. Use of such solutions may cause corrosion, finish peeling, and/or dull the surface.
• DO NOT USE: Abrasive sponges or cloth. Never use steel, wool, or wire brushes that will permanently scratch the surface.
• Retain these installation instructions for future reference!
• If you have any questions or concerns, please do not hesitate to contact us by Email: service@bestgosupplychaininc.com Hotline: 626679 3588

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>