wayfair Outdoor Tankless Water Heater Installation Guide

Outdoor Tankless Water Heater
Installation Guide

Outdoor Tankless Water Heater

Determine Installation Location

The tankless water heater cannot be installed in a shower room, basement, closet, or kitchen. It is ok to install outdoor or balcony. Refer to the Illustration for clear space required around the tankless water heater

Tools And Materials Needed

Parts included
Tools needed
Materials needed
Materials that may be needed

Check And Open Package

Before opening the package, please check it any damages in the packaging box, also check if it is the right item you have purchased. If everything looks correct, please continue to open the water heater box, and then check whether any damages to the machine, and all accessories are coming altogether. The accessories should include installation guide, owners manual, and a fittings bag.

Position By Paper Drilling Templa

Carefully measure the space and calculate where to Install the water heater per the exhaust pipe position. Use the paper drilling template from the accessories to position and adjust. Pay attention to the minimum distance from combustible or non-combustible objects.

Drill And Fix Screws

Drill holes in the wall using an impact drilL Put the plastic ribbed anchors into the holes first, and then the screws, and tight them up.

Mount to Wall

Hang the water heater onto the anchor screws, and tight the machine up with other screws coming altogether.

Connect Valves, Water And Gas Pipes

Install a cold water isolation valve to the water inlet, and a hot water isolation valve plus a pressure relieve valve to the hot water outlet. Make sure connect cold and hot water pipes respectively to the cold water inlet and hot water outlet.

Check For Leakage

Turn on the water and gas, check if there’s any water leakage; also use soapy water or gas leak detector to check if any gas leakage from the gas pipes and Minns.

Connect Remote Controller to Machine

The remote controller can be Installed In the bathroom. Attach the remote control to the wall with screws supplied, and connect the machine.

Turn On Water Heater

Plug In and turn on the water heater. Check whether the water heater Ignites and runs successfully.

Try And Enjoy It

Try the water temperature before use… and enjoy!
Water Heater Installation Check List:

• Unbox and check whether the water heater, installaon manual and owner’s guide, parts and accessories bag, wired digital controller (outdoor gas water heater models only) are coming In the box.
• Check to ensure there are no corrosive chemicals in the air intake.
• Water supply should be free of chemicals, and water hardness that higher than allowed level may damage the water heater.
• Ensure there is enough space required for installaon.
• Ensure there is enough distance required between the exhaust vent and air inlet of houses.
• Ensure you are using the right exhaust vent products, and follow the installaon manual from the suppliers.
• For indoor water heater models, ensure the number of elbows used does not exceed the maximum quanty allowed, and the exhaust vent pipe’s total length (including the elbows, each is equivalent to 6 feet) does not exceed the maximum length allowed for the water heater.
• For indoor water heater models, ensure the exhaust vent pipe is outward and downward the slope of 3 degrees.
• Turn off hot water switch, turn on cold water switch and the drain screw, flush the debris and air out of the water pipes. Debris inside the water my damage the water heater. Please use buckets or extra water pipes if needed.
• Ensure hot water pipes and cold water pipes are not penetrang through water heater, and no water leakages.
• Turn off cold and hot water switches before cleaning up water inlet filter. Put a bucket under the water heater’s filter to catch any water out of the water heater. Screw out the water inlet filter, wash off debris and dusts, and then hand screw the filter back in. When it’s done, turn on the cold and hot water switches.
• Ensure the pressure relieve valve’s relieving capacity exceeds that of the water heater BTU input rang. Please refer to the specificaons on the side of machine for BTU input rangs.
• Install a manual gas shut-off valve between the water heater and your gas supply line.
• Check to confirm there is no gas leakage in piping and fings.
• Confirm the gas inlet pressure in the min -max range as required.
• Confirm you are using the gas type as required by the water heater.
• Confirm the power supply is 120 VC/60 Hz, and properly grounded.
• Confirm the thermostat works normally.
• Connect a gas manometer to the pressure port to verify the system is working normally. Turn on appliances that use high flow rate hot water and set the water heater to its maximum operaon capacity, the inlet gas pressure must be higher than the minimum pressure on the specificaon label.
• Do not induct poisonous chemicals into drinking water, like the chemicals used to process broiler water. Drain the water out of the water heater if you are not using the water heater for a significant me period.
• For outdoor Tankless Water Heater models, confirm the wired digital controller is installed correctly.

Thank you very much for choosing FOGATTI!
If you have any questions, please feel free to contact us
we will be the firsttime to solve your problems!
**** Tel.: 305-998-1595/855-881-5258 (8:30am-5:00pm EST Monday-Friday)
Email: service@fogatti.com.cn
Messenger: Fogatti Mall
Fogatti Technical Service Department
Add.: GROUP 8113 NW 68TH ST, MIAMI, FL 33166-2757 US              

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>