wayfair 6pack Aether LED Touch Light User Manual
- June 5, 2024
- wayfair
Table of Contents
wayfair 6pack Aether LED Touch Light User Manual
Specifications
Input Power Supply: 5V 2A
Output Power: 5V
Light Source: RGB LED
Power Consumption: (hex)1.2W/(Tri) 2.4W
Lumens : 120 LM(hex)/240LM(Tri)
Remote Control Range: 5—8 Meters
Size of the Product: (hex)10.3 x 9 x 3 CM/ (Tri) 15.2 x 13.2 x 3 CM
Length of USB Cable: 5 Feet/1.5 Meters
Cautions
- Please only use a high-quality Adapter (Output 5V 2A) or the Lights will not work properly.
- Do not connect more than twenty (12) LED Touch Lights on USB cable.
- White LED Color consumes the most energy. Do not connect more than twelve (10) Lights when set to White.
- The center of the Light responds best to the Touch function.
- Always point the Remote Control toward the Lights, within the Range.
Remote Control Functions
| Buttons | Functions | Buttons | Functions |
|---|---|---|---|
| ON/OFF | Turns On/Turns Off | Clock | Sets LED Lights on a Timer |
—Turns Off in 30 Minutes
FLASH| Makes All Colors Glow| Color Selections| Choice of Colors
FADE| Smoothly Shuffles Colors| Arrow Upward| Brightness Up (4-grade）
JUMP| Quickly Changes Colors| Arrow Downward| Brightness Down (4-grade）
Installation Instructions
- Place all Lights face-down. Insert PCB Boards to connect the Lights. Build a design shape of your choice.
- Keep the side of the USB board with 2 smaller arrows in the same aide of the face of the light.
- Snap in the Connectors on the holes of the Lights to keep the unit sturdy.
- Insert the USB Cable into the Adapter. Find the USB Port on the Light closest to the desired wall outlet.
- Connect the other end of the USB Cable to the LED Touch Light. Plug the Adapter into the wall outlet.
- Remove the insulation to activate the Remote Control. Press ON while pointing at the Lights.
- Make sure every Light works. Try using different PCB Boards if any Lights don’t work.
- Unplug the Adapter, then place the Lights face-down on a flat surface.
- Peel the paper from the Double-Sided Adhesive, and paste one side in the circled back on the Lights.
- Find a place to display the Lights. After cleaning and drying the area, press the Adhesive Tape to the wall.
- The PCB Boards are strong enough to further support the Lights on a Hook, Nail, or Screw (not included).
- Plug the Adapter back into the wall outlet. Choose from the Colors or Mode Settings with the Remote Control.
- Touch the Lights to individually change the Colors or Mode Settings to customize your glow.
- Free USB Ports on the Lights can be used to charge other devices.
- Please, DON’T supply power to any other device while the Lights are in White LED Color mode.
- If ever there are questions about proper electrical usage, consult a licensed technician.
How to use the stand
Use the plastic L shape stand to put the hexagon tiles on table.
- Link the lights with correct USB connecting boards and triangle connectors according to your own design.
- Connect the USB power cable to check if every light is working well, and then pull out the USB cable.
- Put a sticker pad on the light you plan to make it the bottom one close to the table.
- Peel the 2 protection films from the L stand, and make the shorter side of the L stand on table.
- Put a side of the bottom light on table and hold it straight, push the L stand (shorter side on table) to the sticker on the back of the bottom light and stick them together sturdily.
- Put another sticker pad on the shorter side of the L stand (facing the table).
- Clean the place on table where you want to put the lights . And then put the stand with the lights there.
Tips of removing the stand from the table:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>