CLIPSAL CLP591011 Wiser Window/Door Sensor User Guide
- June 6, 2024
- CLIPSAL
Table of Contents
- CLIPSAL CLP591011 Wiser Window/Door Sensor
- Getting to know the product
- Package contents
- Choosing the installation location
- Mounting the sensor
- Mounting
- Operating elements
- Setting the sensor
- Technical data
- Customer Care
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CLIPSAL CLP591011 Wiser Window/Door Sensor
Prerequisites
Download the Wiser by SE App to your smartphone and install the Wiser
Gateway/Hub (hereinafter referred to as Wiser Hub) to configure and control
Wiser devices.
For your safety
NOTICE RISK OF DAMAGE TO DEVICE
Always operate the product in compliance with the specified technical data.
Failure to follow these instructions can result in equipment damage.
Getting to know the product
The Wiser Window/Door Sensor (hereinafter referred to as sensor) consists of two separate parts: primary and secondary. The primary part includes the sensing circuit which detects the secondary part. The second part is a magnet.
When the sensor is connected to the Wiser Hub and the window/door is opened or closed, the primary part directly reports the change to the Wiser Hub.
When the battery is low (less than 10 %), the status LED blinks orange once per minute, and a message is sent to the Wiser Hub.
Package contents
A Primary part (sensing circuit)
B Secondary part (magnet)
C Baseplate
D Adhesive pad
E Screws: 2 × ST4.2 × 25 mm with wall plugs
F Installation instructions
Choosing the installation location
Install the primary and secondary parts as per the suggested location:
G Correct and incorrect secondary part/base plate alignment
H Vertical mounting options
I Horizontal mounting options
Mounting the sensor
Removing the battery isolation strip
Mounting
- For wood or plastic surfaces, use either the adhesive pad or the mounting screws.
- If using screws, pre-drill a 1 mm hole.
- For metal surfaces, use adhesive pads only.
- To avoid degrading sensor performance, do not install the sensor near magnetic devices.
- With the window/door in the close state, the distance between the primary part and secondary part of the sensor should be <18 mm for a non-metallic base (for example, wood or plastic surfaces) and <10 mm for a metallic base.
Operating elements
J Status LED
K Base cover screw
L Function key
M Baseplate
Setting the sensor
Remove the primary part from the base plate to access the function key L.
Connecting to the Wiser Hub
- Short press (< 0.5 s) the function key 3 times by hand or pencil, the status LED blinks amber.
- Add the sensor in the Wiser by SE App and follow the instructions. The status LED turns green when the sensor successfully connects to the Wiser Hub.
Resetting the sensor
Short press (< 0.5 s) the function key 3 times and then long-press the
function key once for >10 s to reset the sensor to factory default mode.
All configuration data, user data, and network data is deleted.
Troubleshooting
Refer to the system user guide.
Technical data
Battery | 3 VDC, CR2450 |
---|---|
Battery life | Up to 5 years (may vary based on the usage, frequency of |
firmware update and environment)
Nominal power| ≤90 mW
Operating frequency| 2405 – 2480 MHz
Max. radio- frequency power transmitted| ≤7 dBm
IP rating| IP20
Operating temperature| −10 °C to 50 °C
Relative humidity| 10 % to 95 %
Primary part dimensions (H × W × D)| 50.3 × 33.0 × 16.3 mm
Secondary part dimensions
(H × W × D)
| 50 × 9 × 9 mm
Certification| Zigbee 3.0
Compliance| __
Dispose of the device separately from household waste at an official collection point. Professional recycling protects people and the environment against potential negative effects.
Trademarks
- Zigbee® is a registered trademark of the Zigbee Alliance.
- Apple® and App Store® are brand names or registered trademarks of Apple Inc.
- Google Play™ Store and Android™ are brand names or registered trademarks of Google Inc.
- Wiser™ is a trademark and the property of Schneider Electric SE, its subsidiaries and affiliated companies.
Other brands and registered trademarks are properties of their relevant owners.
Customer Care
Warranty information
We warrant this product for 1 year. See Warranty links below.
Schneider Electric (Australia) Pty Ltd
33-37 Port Wakefield Road, Gepps Cross SA 5094
Customer Care: 13 73 28
Email: customercare.au@se.com
Warranty:
https://www.se.com/au/en/about-us/legal/terms-and-conditions.jsp
www.se.com
Schneider Electric (NZ) Ltd
Building 6, 60 Highbrook Drive,
East Tamaka, Auckland 2013
Customer Care: 0800 652 999
Email: sales@nz.schneider-electric.com
Warranty
https://www.se.com/nz/en/about-us/legal/terms-and-conditions.jsp
www.se.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>