CLIPSAL CLP595011 Wiser Motion Sensor User Manual

: June 6, 2024
: CLIPSAL

Table of Contents

Prerequisites
Additional system information
For your safety
Getting to know the product
Package contents
Choosing the mounting location
Mounting the sensor
Operating elements
Setting the sensor
Behaviour of the status LED
Troubleshooting
Technical data
Customer Care
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CLIPSAL CLP595011 Wiser Motion Sensor User Manual

Prerequisites

Download the Wiser by SE App to your smartphone and install the Wiser Gateway/Hub (hereinafter referred to as Wiser Hub) to configure and control Wiser devices.

Additional system information

Detailed product information is available online in the system user guide: Scan the QR code for your region.

AU
NZ

For your safety

NOTICE

RISK OF DAMAGE TO DEVICE

Always operate the product in compliance with the specified technical data.

Failure to follow these instructions can result in equipment damage.

Getting to know the product

The Wiser Motion Sensor (hereinafter referred to as sensor) reports the detection of movement to the Wiser Hub (and actuator to perform configured functions), measures the luminance of the environment and passes this data to the Wiser Hub. The threshold of luminance settings and/ or detection of movement can be programmed to determine what action to be taken at that moment.

When the sensor is connected to the Wiser Hub, it directly reports motion detection data to the hub. When the battery is low (less than 10%), the status LED blinks orange once per minute, and a message is sent to the Wiser Hub.

Package contents

A Motion sensor
B Base plate
C Adhesive pad
D Screws: 2 × ST4.2 × 25 mm with wall plugs
E Installation instructions

Choosing the mounting location

Mounting location

The sensor can be mounted on a wall or ceiling to
provide desired coverage:

Ceiling mount provides a 360° detection angle with a maximum range of 4 m diameter.
Wall mount provides a detection angle of 90° to 110° horizontal and vertical with a maximum range of 5 m radius.
Do not install the sensor in a place where there is strong sunlight or wind (for example, close to ventilation).
When the ambient temperature is >32°C, the sensor’s ability to measure sensitivity, detection range, and detection angle are degraded.

Walking direction

The PIR sensor is more sensitive to movement across different patterns. On the contrary, the sensor is less sensitive when movement is directly towards the sensor, since the range is reduced.

F More sensitive to movement across the pattern
G Less sensitive to movement directly towards sensor

Mounting the sensor

**Removing the battery isolation strip

**

Mounting

For wood or plastic surfaces, use either the adhesive pads or mounting screws.
If using screws, pre-drill a 1 mm hole.
For metal surfaces, use the adhesive pads only.

Operating elements

H Function key
I Sensor
J Status LED
K Base plate lock/unlock instruction:
Turn to lock into base plate
Turn to unlock from base plate
L Base plate

Setting the sensor

Remove the sensor from the base plate to access the function key H.

Connecting to the Wiser Hub

Short press (< 0.5 s) the function key 3 times by hand or pencil, the status LED blinks amber.
Add the sensor in the Wiser by SE App and follow the instructions. The status LED turns green when the sensor successfully connects to the Wiser Hub.

Resetting the sensor

Short press (< 0.5 s) the function key 3 times and then long press the function key once for >10 s to reset the sensor to factory default mode.

All configuration data, user data, and network data are deleted.

Replacing the batteries

While refastening the battery cover make sure the triangle marks on the battery cover and the PCBA align.

Behaviour of the status LED

Refer to the system user guide.

Troubleshooting

Refer to the system user guide.

Technical data

Battery	3 VDC, LR03 AAA ×2
Battery life	Up to 5 years (may vary based on the usage, frequency of

Dispose of the device separately from household waste at an official collection point. Professional recycling protects people and the environment against potential negative effects.

Trademarks

Zigbee® is a registered trademark of the Zigbee Alliance.
Apple® and App Store® are brand names or registered trademarks of Apple Inc.
Google Play™ Store and Android™ are brand names or registered trademarks of Google Inc.
Wiser™ is a trademark and the property of Schneider Electric SE, its subsidiaries and affiliated companies.

Other brands and registered trademarks are properties of their relevant owners.