CLIPSAL USB Chargin Instructions
- June 7, 2024
- CLIPSAL
Table of Contents
by Schoneider Electric
Iconic® Series
USB Charging Module
Installation Instructions
PDL342USB2AC-VW Dual USB Charging Mechanism 40E2USBACM-VW
PDL342USB-VW 40E1USBM-VW USB Charging Mechanism
40E2USBM-VW PDL342USB2-VW Dual USB Charging Mechanism
NOTICE
HAZARD OF EQUIPMENT DAMAGE (LOAD)
The USB Charging Mechanism is intended for devices that are designed to be
recharged via a USB port.
- Do not attempt to connect devices that are not designed to be charged via a USB port.
- Do not parallel-connect the USB ports in order to achieve higher current output. The ports are intelligent ports that communicate with devices to optimize the charge current.
- Always use the USB charging cable supplied with the device to be charged.
- There are no user-serviceable parts inside the USB charging mechanism.
**Failure to follow these instructions may result in damage to the USB Charging Mechanism and connected equipment.
** NVE75248-02
12-2018
For your safety
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• This product must be installed and serviced by appropriately qualified
and/or licensed electrical personnel.
• Isolate the electrical supply before doing any work on this product.
• Ensure that the product has been correctly installed and tested for safe
operation before reconnecting the electrical supply.
Failure to follow these instructions will result in death or serious injury.
WARNING
RISK OF ELECTRIC SHOCK
Hazardous voltage and electrical current may be present at the wire leads of
this product even when the device is switched off.
• Lockout and tag the input circuit before accessing the wiring connections.
• Use the supplied terminal block to connect the USB Charging Mechanism to the
electrical circuit.
• After wiring, wrap the terminal block with insulating tape.
Failure to follow these instructions can result in death or serious injury.
CAUTION
HAZARD OF EQUIPMENT DAMAGE
Install the device according to the instructions in this document.
• Pay attention to the specifications and wiring diagrams related to the
installation.
• Do not use this product for any other purpose than specified in this
instruction.
Failure to follow these instructions can result in minor injuries or equipment
damage.
NOTICE
RISK OF EQUIPMENT DAMAGE OR MALFUNCTION (WIRING CONNECTIONS)
To avoid damaging the equipment and possibly voiding the warranty:
• Test operation during installation and correct any wiring errors
immediately.
• Keep cable insulation away from the sides of the enclosure to avoid possible
damage or long-term degradation of the cable insulation.
Failure to follow these instructions can result in equipment damage or
malfunction.
Unit operation
• Connect device(s) to the USB port(s) on the USB charging module using the
USB cable supplied with the device.
• The USB charging module will negotiate with each device to provide an
optimized charging current.
• If two high-demand devices such as large tablets are connected to a dual-
port USB charging module, the devices will negotiate with the module for the
amount of charge current they require. As connected devices increase their
charge level, the amount of current they require will decrease.
Setting the USB port orientation during installation
1. Hold the
body of the USB Mechanism with one hand .
2. Use your other hand to rotate the USB Port Head in either direction until
the Head clicks into place. The Head rotates in 90° increments.
3. Keep rotating the USB Port Head until you reach the desired orientation.
Once installed, the USB port orientation should be as shown in , or as the
customer requires.
Wiring diagram
• Use the terminal bock supplied with the USB charger to connect the module to
the mains circuit.
• After wiring, wrap the terminal block with insulation tape.
Technical specifications
Parameter| 40E2USBACM-VW PDL342USB2AC-VW| 40E1USBM-VW PDL342USB-
VW| 40E2USBM-VW PDL342USB2-VW
---|---|---|---
Nominal operating voltage| 220-240 VAC
Nominal operating frequency| 50 Hz
Mounting/installation options| 1, 2 & 3 gang wall plates as well as the
extra switch position in single, double, and quad-socket outlets
Maximum input current| 300 mA| 100 mA| 200 mA
USB port type Maximum port output| 1x Type A
5 VDC, Up to 2.4 A
| 1x Type C
5 VDC. Up to 3.1 A
| 1x Type A
5 VDC, 1.5 A
| 2x Type A
5 VDC, 2.1 A
Maximum unit output| 5 VDC, 3.1 A| 5 VDC, 1.5 A| 5 VDC, 3.1 A
Mounting depth in mm| 55 mm| 40 mm| 55 mm
Short circuit protection| Yes
Thermal over-current protection| Yes
Over-temperature protection| Yes
Thermal fuse| Yes
Multi – gang plate capacity| Maximum 2 modules per plate|
Maximum 3 modules per plate| Maximum 2 modules per plate
USB port orientation| Independent of the mechanism body orientation
Available cap styles| Color packs for USB port caps: Vivid White (VW),
Warm White (WY), Cool Grey (CY), Anthracite (AN). Ash Grey (AG)
Compliances standards| AS/NZS 61558.2.16
EMC compliance| AS/NZS CISPR 22, AS/NZS CISPR 24, AS/NZS 61000-3-2
AS/NZS 61000-3-3
MEPS standard| 4665
Troubleshooting
Problem | Recommended Resolution |
---|---|
A connected device is not charging. | • If the charging port is on a Dual Port |
USB Charging Mechanism, connect the device to the other charging port. If the
device charges, there may be a problem with the mechanism charging port.
• Connect the device to the charging port using another compatible USB cable.
If the device charges, replace the faulty cable.
• Connect the device to another compatible charger. If the device charges,
there may be a problem with the mechanism charging port.
A large tablet (or similar high-demand device) takes an unusually long time to
charge.| • If the device is connected to a Single Port USB Charging Mechanism,
the maximum output from the port (1.5 A) may be less than the optimal output
required by the device. The device should still charge, albeit over a long
period of time.
• The Ionic Dual Port USB Charging Mechanism has a higher maximum output and
is better suited to charge higher-demand devices such as large tablets.
• If the cable being used to connect the device to the charger is not the
cable that was supplied with the device, try a genuine cable. Cheap non-
reputable cables are a common source of charging issues with devices.
Two large tablets (or similar high-demand device) take longer to charge when
both are connected to the Dual Port USB Charging Mechanism.| • On dual port
chargers, the double type A charger has a single output rate of 2.1 A, except
when both ports are used together it reduces to a maximum output rate of 3.0
A. Chargers with Type A (2.4 A output) and Type C (3.0 A output) have a
reduced output of 3.0 A when used together.
• When two high-demand devices that are low on charge are connected to the
Dual Port Mechanism, the maximum output is shared between the two charging
ports and each device may therefore receive less than optimum charging output.
Customer care
Warranty Information (Australia)
We warrant this product for 2 years.
visit https://www.schneider-electric.com.au/en/about-us/legal/terms-and-
conditions.jsp for details.
Our goods also come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Warranty information (New Zealand)
We warrant this product for 2 years.
visit https://www.schneider-electric.co.nz/en/about-us/legal/terms-and-
conditions.jsp
for details. Schneider Electric (Australia) Pty Ltd
33-37 Port Wakefield Road,
Gepps Cross, SA 5094
Customer Care: 13 73 28
Email: customercare.au@schneider-electric.com
www.schneider-electric.com.au
Schneider Electric (NZ) Ltd
38 Businesss Parade South, HighBrook
East Tamaki, Manukau 2013
Customer Care: 0800 652 999
Email: sales@nz.schneider-electric.com
www.schneider-electric.co.nz
Schneider Electric reserves the right to change specifications, modify designs and discontinue items without incurring obligation, and whilst every effort is made to ensure that descriptions, specifications, and other information in this catalog are correct, no warranty is given in respect thereof and the Company shall not be liable for any error therein.
© Schneider Electric 2018
This material is copyright under Australian, New Zealand, and international
laws. Except as permitted under the relevant law, no part of this work may be
reproduced by any process without prior written permission of and
acknowledgment to Schneider Electric.
Patent notice
This product is the subject of one or more patent and/or design applications and/or registrations. More information can be found on our website
References
- Electric | The Largest Consumer Energy & Renewables Platform
- Schneider Electric Global | Global Specialist in Energy Management and Automation
- Schneider Electric New Zealand | Global Specialist in Energy Management and Automation
- Schneider Electric Australia | Global Specialist in Energy Management and Automation
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>