NiteRider 150-24210-007 Technical Lighting Systems High Powered LED

Lights

LUMINA™ 1200 BOOST FRONT LIGHT USER GUIDE
UNLOCK BEFORE USE. LOCK THE HEADLAMP BEFORE TRANSIT OR STORAGE
It is important to lock the headlamp and protect the switch from being pressed while it is in transit. The headlamp can be easily turned on if placed in something like a backpack, duffel bag or suitcase. The headlamp gets hot while in operation. To prevent potential damage from high heat or even fire, it is very important to put the headlamp in lock mode and protect the switch from being pressed NiteRider® will not be held responsible for damages to person or property resulting from a failure to follow the ‘lock’ mode instructions.

IMPORTANT

WARNING
A bicycle without lights and reflectors might be difficult for other people to see, and you might not be able to see. If you cannot see, or other people cannot see you, you could have an accident. Make sure your lights operate correctly and that batteries are charged.
WARNING HHOT SURFACES!
DO NOT USE THE LUMINA™ AS A HAND-HELD LIGHTING DEVICE WHEN IN HIGH AND BOOST MODES!

PARTS LIST AND IDENTIFICATION

Please verify the contents of your Lumina™ Boost lighting system:

• Lumina TM Front Ugh!
• Handlebar Clamp Mount
• USB Charging Cable

MOUNTING THE HANDLEBAR CLAMP MOUNT AND HEADLIGHT

The Handlebar Clamp Mount (HCM) is designed to fit on virtually any handlebar (25.4mm – 35mm diameter handlebars).

1. Turn the knob counter-clockwise, allowing the hinge to swing open.
2. Place the HCM on the handlebar on the left side of the stem, orienting the mounting rails with the release tab towards the rear.
3. Swing the hinge down to make contact with the handlebar.
4. Swing the bolt up, seating the knob into its recess.
5. Turn the knob clockwise to tighten and secure the mount to the handlebar.

Mounting the headlight onto the handlebar clamp mount
With the light facing forward, align bottom mounting rails of light to the top of rails of HCM. Pull light back along the rails until the tabs engage and lock into place. Test for a secure fitment by pushing the light forward, ensuring there is no movement and that tabs have engaged into the light base. Do not push the release tab when testing for a secure fitment. To remove the headlight, press the release tab down and slide the headlight forward.
Note: After mounting the headlamp, adjust it so the beam illuminates your path without distracting oncoming riders.

Available optional accessories

• 6349 – Lumina TM Helmet Mount

• 8541 – Lumina TM Stick-On Mount

• -MOUNTING RAILS

• 6645 – Lumina TM Handlebar Rubber Strap Mount

• 4005 – NiteRider® GO Action Adapter

• 4009 – NR GO ActionCam C2 Handlebar Mount (#4005 – GO Action Adapter Required

OPERATION

Unplug the light from the charger before use

1. For the initial power on, the light will need to be unlocked. Press and hold the power button for 8-10 seconds to unlock.
2. A single press of the power button will power up the light.
3. Go through steady light modes by pressing the power button once.
4. To access boost mode, double-tap the power button. A single press of the power button will return to normal steady modes.
5. To access flash modes, press / hold the power button for 3 seconds until the light begins to flash.
6. To access walk mode, press / hold the power button for 3 seconds until the light begins to flash. Cycle through the 2 flash modes until low steady walk mode light comes on.
7. To power off the light, press and hold the power button until the light turns off.
8. To lock/unlock the light, press and hold the power button for 8-10 seconds

RUN TIMES

LOW BATTERY INDICATOR
The Low Battery Indicator is located in the power button. The LED in the power button will light up blue when battery levels are greater than 20%. When battery levels are below, less than 20%, the Indicator with change to red.

BATTERY CHARGING AND CARE

1. Plug the USB Charging Cable into the USB port located on the bottom of the light. Then plug the other end into a powered-on computer or directly to a wall outlet using an AC adapter (not included).
2. The LED indicator in the power button will light up red while the battery is charging. When the battery is fully charged, the LED light up blue.
3. Unplug the AC Adapter from the battery by grasping the connectors rather than the cable.
4.  It is good practice to store your battery away with a full charge.

For extended periods, charge the battery every three months to maximize its lifespan

CHARGE TIMES

Your Lumina™ Series light features NiteRider’s lntelliCharge function. This allows the Lumina to recognize the type of USB Charge Port it is connected to and adjust the charge rate accordingly. If the Lumina is connected to a USB Charge Port with an output greater than 500mA, it will charged twice the normal rate.

• 6:00 hours at 500mA
• 3:00 hours at greater than 500mA
• charge times may vary.
• Some USB Charge Ports may not charge at a faster rate

LED Indicator

• While charging, the red LED will flash at a certain speed to indicate which charging rate is currently being used. The LED will flash approximately once every two seconds to indicate the normal
• charging rate and will flash twice every second to indicate the faster charging rate. The LED will light up solid blue to indicate that the battery is fully charged.

OPTIMAL VIZ WITH NITERIDER

• While a Lumina Boost lighting system will improve your view and visibility, control and enjoyment of riding, please remember that cycling can be an inherently dangerous activity. In addition to using your lighting system properly and riding with extreme caution, NiteRider” urges you to:
• Obey your local traffic laws
• Always let someone know where you are going
• Wear a helmet, highly visible and reflective clothing
• Cany an auxiliary light and emergency supplies
• Make sure the headlamp and mounting bracket are securely fastened
• Always set your light to lock mode during transport or storage

PROTECTING YOUR INVESTMENT

• Properly charge your battery to maximize its lifespan (see the “Battery Charging and Care” section for detailed information).
• The Lumina•M 1200 Boost will perform in wet weather conditions, but submerging it in water
• will damage the system. To prevent water damage, ensure USB port cover remains tightly sealed while operating your light.

SUPPORT

• If you experience difficulties during product installation or operation, NiteRider” provides free telephone support on weekdays from
• 8:00 am to 4:30 pm (Pacific Time) at 800.466.8366, Ext 4.
• You may also e-mail us at support@niterider.com.

WARRANTY

• NiteRider'” stands behind its products with the following warranties:
• Lifetime warranty: Covers any defects in material and workmanship, mechanical components (housings, covers, mounts and fasteners), and LEDs
• 2-year warranty: Printed circuit boards, switches, and AC adapters
• 1-year Warranty: Rechargeable battery cells To obtain warranty service have your original sales receipt. Contact the NiteRider’s” Customer Service
• Department at 800.466.8366, Ext. 4 to obtain a Return Merchandise Authorization (RMA) number.
• The RMA number must be prominently displayed on the outside of your package.
• The product must be properly packaged to prevent damage in transit. For International customers, please contact your local NiteRider'” Distributor. Go to: niterider.com/pages/international-distributors
• For complete warranty information, please visit our website at www.NiteRider.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>