Niterider Technical Lighting Video Systems 071-24704 Remote Switch User Guide

The NiteLink™ Remote Switch is a peripheral device to NiteLink™ compatible headlights and taillights.

PARTS LIST AND IDENTIFICATION

Please verify the contents of your NiteLink™ Wireless Remote:
A. Wireless Remote
B. Handlebar Mount
C. CR2032 Battery (In unit)
D. 3mm Allen Key (not supplied)

MOUNTING THE REMOTE

1. The NiteLink™ Wireless Remote can be mounted on the right or left side of your handlebars.
   If required, use a 3mm Allen Key Wrench to remove the outside Bolt and set your desired orientation.
   SEE
   |
   ---|---
2. Remove clamp bolt, open hinge, and set mount onto handlebar location.
3. Tighten clamp bolt to secure in place.

OPERATION

The power button turns ON and OFF the NiteLink™ remote switch and turns ON and OFF all devices that are paired to the NiteLink™ Compatible
Headlight.

1. Press the power button to turn ON all paired lights. Press and hold 1.5 seconds will turn OFF all paired lights.

2. The toggle switch brightens or dims the NiteLink™ Compatible headlight/s.

3. Push and release the toggle switch forward to brighten the headlight one step.

4. Pull and release the toggle switch back to dim the headlight one step.

5. Push and hold toggle switch forward, to brighten the headlight continuously until the headlight reaches maximum brightness, Boost Mode.

6. Pull and hold toggle switch back to dim the headlight continuously until the headlight reaches minimal brightness, Walk Mode.

7. To access Flash Modes on headlight/s, Tap the Power Button headlight will begin to flash.

8. Push or pull the toggle switch, which will cycle through the daylight Flash running modes on the headlight.

9. Push and hold the toggle switch to cycle through the daylight Flash running modes continuously. Note that the headlight will return to steady mode if the Power button is Tapped

10. Pulling back the toggle switch will cycle the daylight running modes in a reverse cycle.

11. Pushing forward the toggle switch will cycle the daylight running modes in a forward cycle.

12. The headlight mode LEDs will indicate the power settings commanded by the NiteLink™ Remote toggle switch.

13. The NiteLink™ Wireless Remote can only power ON or OFF a paired taillight. To change modes on taillight, press the power button directly on the
    taillight unit.

14. NiteLink™ Wireless Remote can be paired to 2 taillights.

PAIRING NiteLink™ COMPATIBLE DEVICES

The NiteLink™ Wireless Remote Switch can handle up to 3 total devices (NiteLink™ Compatible Headlights and Taillights).

1. Tapping the power button on the NiteLink™ Wireless Remote for the FIRST TIME will enter pairing mode.
2. For NiteLink™ Compatible Headlights, press and hold switch #1 and #2 simultaneously for 2 seconds to enter pairing mode. This will sync the  NiteLink™ Remote and headlight.
3. The blue and arrow LEDs on the remote switch will flash to confirm pairing.
4. To add additional devices refer to pairing instructions of that device.

OPERATION FOR MULTIPLE TAILLIGHTS AS TURN INDICATORS

1. When 2 NiteLink™ compatible taillights are paired to the NiteLink™ Wireless Remote, the left arrow button commands the left NiteLink™  compatible Taillight to blink as a turn signal, and the right taillight to go high steady mode.
2. The right arrow button commands the right taillight to blink as a turn signal and the left taillight to go high steady mode. The directional arrow will blink yellow when activated.
3. To cancel the turn indicator, tap the same directional arrow to reset both synced taillights back to their previous preset modes.

LOW BATTERY INDICATOR

When the battery is low in voltage, the red power button will flash 3 times then pause and blink 3 more times whenever the power button is pressed, blue fuel gauge led is not lit. The remote switch will still operate until the battery voltage cannot drive the remote switch, the CR2032 battery should be replaced as soon as possible to keep normal operation. Follow the instructions on the back of the remote switch.

OPTIMAL VIZ WITH NITERIDER®

Please remember that cycling can be an inherently dangerous activity. In addition to using your lighting system properly and riding with extreme caution,
NiteRider® urges you to:

• Obey your local traffic laws
• Always let someone know where you are going
• Wear a helmet, highly visible and reflective clothing
• Carry an auxiliary light and emergency supplies
• Make sure the taillight and seat post strap mount are securely fastened
• Fully charge your taillight after use to exercise good battery health

PROTECTING YOUR INVESTMENT

The NiteLink™ Wireless Remote will perform in wet weather conditions, but submerging it in water will damage the system.

SUPPORT

If you experience difficulties during product installation or operation, NiteRider® provides free telephone support on weekdays from 8:00 am to 4:30 pm (Pacific Time) at 800.466.8366, Ext 4.
You may also e-mail us at help@niterider.com.

VERIFIER INTEGRATED NFC TECHNOLOGY

The NiteLink™ Wireless Remote is equipped with integrated NFC technology.

Tap your mobile device on the VerifiR Logo located on the top of the light to launch the NiteRider® VerifiR experience.
Within the NiteRider® VerifiR experience you can quickly and easily:

• Learn how to unlock/lock your light
• Register your product
• Access How to / User Guides
• Report your light lost or stolen

SUPPORT

If you experience difficulties during product installation or operation, NiteRider® provides free telephone support on weekdays from 8:00 am to 4:30 pm (Pacific Time) at 800.466.8366, Ext 4.
You may also e-mail us at support@niterider.com.

WARRANTY

NiteRider® stands behind its products with the following warranties:

• Lifetime Warranty: Covers any defects in material and workmanship, mechanical components (housings, covers, mounts, and fasteners), and LEDs
• 2-year warranty: Printed circuit boards, switches, and AC adapters
• 1-year Warranty: Rechargeable battery cells
  To obtain warranty service have your original sales receipt. Contact the NiteRider® Customer Service
  Department at 800.466.8366, Ext. 4 to obtain a Return Merchandise Authorization (RMA) number.
  The RMA number must be prominently displayed on the outside of your package.
  The product must be properly packaged to prevent damage in transit.
  For International customers, please contact your local NiteRider® Distributor. Go to: niterider.com/pages/international- distributors

For complete warranty information, please visit our website at www.NiteRider.com

Industry Canada Compliance

NiteLink™ Wireless Remote – (P/N 24704), IC: 26701-24704
This device complies with the Industry Canada license-exempt RSS standard. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
IC Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 cm between the radiator and your body.
Federal Communication Commission Compliance
NiteLink™ Wireless Remote- FCC ID: 2AXZQ-24704
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC CAUTION:
TO ASSURE CONTINUED COMPLIANCE, ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THIS EQUIPMENT. (EXAMPLE – USE ONLY SHIELDED INTERFACE CABLES WHEN CONNECTING TO COMPUTER OR PERIPHERAL DEVICES).
FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons and must not be co- located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>