NiteRider Solas 250 Bike Taillight User Manual

May 15, 2024
NiteRider

NiteRider Solas 250 Bike Taillight

NiteRider-Solas-250-Bike-Taillight-PRODUCT

Product Information

Specifications:

  • Product Name: SOLASTM 250 Taillight
  • Contents:
    1. SolasTM 250 Taillight
    2. Rubber Seat Post Strap Mount
    3. USB Charging Cable
  • Charging Time: Approximately 4 hours (Charge times may vary)
  • Battery Health Reminder: Charge the taillight every three months for good battery health
  • Water Resistance: Perform well in wet weather conditions, avoid submerging in water

Product Usage Instructions

Mounting the Rubber Seat Post Strap Mount:

  1. Position the Rubber Seat Post Strap Mount with Mounting Rails facing towards the rear of the bike and the Release Tab facing downward.
  2. Pull the rubber strap out and wrap it around the seat post, ensuring even tension.
  3. Hook the rubber strap into the notch to secure it in place.

Mounting the Taillight onto the Rubber Seat Post Strap Mount:

  1. Align the Clothing Clip of the taillight with the Mounting Rails of the Rubber Seat Post Strap Mount.
  2. Slide the taillight downwards within the rails until it locks into place.
  3. To test for secure fitment, push the light upward without pressing the release tab.
  4. To remove the taillight, depress the Release Tab and slide the light upward.

Operating the Taillight:

  1. Ensure the light is unplugged from the charger before use.
  2. Press the power button once to turn on the taillight.
  3. Press the power button to cycle through different light modes.
  4. To power off, press and hold the power button. A low battery indicator will appear when battery levels are low.

Battery Charging and Care:

  1. Plug the USB Charging Cable into the taillight’s USB port and connect it to a powered-on computer or wall outlet using an AC adapter.
  2. The LED indicator will turn red while charging and blue when fully charged.
  3. Unplug the AC adapter by grasping the connectors, not the cable.
  4. For optimal battery health, store the taillight with a full charge and charge it every three months for extended periods of non-use.

FAQ

Q: How do I know when the battery is low?

A: The low battery indicator will light up red when battery levels are below 20%.

Q: Can I use the taillight in heavy rain?

A: The taillight is designed to perform well in wet weather conditions, but avoid submerging it in water to prevent damage.

NITERIDER® INITIATIVE

In 2012, NiteRiders’ initiative campaign “Lights 4 Lives” dramatically improved the cycling landscape; sparking awareness for the need to use bike lights for both Day and Nightime riding. Since then, Daytime Visibility for cycling has been gaining more traction, instilling the idea of added safety for avid cyclists in an age of multi-tasking drivers.

PARTS LIST AND IDENTIFICATION

Please verify the contents of your Solas™ 250 lighting system:

  • A. Solas™ 250 Taillight
  • B. Rubber Seat Post Strap Mount
  • C. USB Charging Cable

MOUNTING THE RUBBER SEAT POST STRAP

MOUNT

FIG.1NiteRider-Solas-250-Bike-Taillight-FIG \(1\)

The Rubber Seat Post Strap Mount (RSPSM) is designed to fit on to most standard seat posts.

  1. Position RSPSM with Mounting Rails facing towards the rear of the bike. Release Tab should be facing downward.
  2. While holding mount in position, pull rubber strap out and around seat post, ensuring even tension throughout the length of the strap.
  3. Hook rubber strap using the appropriate notch and secure into position.

MOUNTING THE TAILLIGHT ONTO THE RUBBER

SEAT POST STRAP MOUNT

FIG.2NiteRider-Solas-250-Bike-Taillight-FIG \(2\)

  1. With the taillight facing rearward, align Clothing Clip of light to Mounting Rails of RSPSM. Slide light downwards within the rails until tab engages and locks into place.
  2. Test for a secure fitment by pushing light upward, ensuring there is no movement and that the Lock Tab has engaged into the Clothing Clip. Do not push the release tab when testing for a secure fitment.
  3. To remove taillight from RSPSM, depress Release Tab and slide light upward.

Note: After mounting the taillight, adjust angle to acheive maximum visibility

OPERATION

FIG.3NiteRider-Solas-250-Bike-Taillight-FIG \(3\)

Unplug light from charger before use

  1. A single press of the power button will power up the taillight.
  2. Press power button to go through flashing and steady light modes.
  3. To power off, press and hold power button. Low battery indicator will appear. See FIG.5.

RUN TIMES

FIG.4

LOW BATTERY INDICATOR

FIG.5NiteRider-Solas-250-Bike-Taillight-FIG \(5\)

When powering off, it will light up blue when battery levels are greater than 20%. When battery levels are below, less than 20%, the Indicator will light up red.

BATTERY CHARGING AND CARE

FIG.6NiteRider-Solas-250-Bike-Taillight-FIG \(6\)

  1. Plug the USB Charging Cable into the USB port located on the bottom of the light. Then plug the other end into a powered-on computer or directly to a wall outlet using an AC adapter (not included).
  2. The LED indicator in the power button will light up red while the battery is charging. When the battery is fully charged, the LED will change to blue.
  3. Unplug the AC Adapter from the taillight by grasping the connectors rather than the cable.
  4. It is good practice to store your taillight away with a full charge. For extended periods, charge the taillight every three months to maximize its lifespan.

CHARGE TIMES

  • 4:00h
  • Charge times may vary

OPTIMAL VIZ WITH NITERIDER®

While a Solas™ 250 lighting system will improve and increase your overall visibility and enjoyment of riding, please remember that cycling can be an inherently dangerous activity. In addition to using your lighting system properly and riding with extreme caution, NiteRider® urges you to:

  • Obey your local traffic laws
  • Always let someone know where you are going
  • Wear a helmet, highly visible and reflective clothing
  • Carry an auxiliary light and emergency supplies
  • Make sure the taillight and seat post strap mount are securely fastened
  • Fully charge your taillight after use to exercise good battery health

PROTECTING YOUR INVESTMENT

Properly charge your battery to maximize its lifespan (see the “Battery Charging and Care” section for detailed information). The Solas™ 250 will perform in wet weather conditions, but submerging it in water will damage the system. To prevent water damage, ensure USB port cover remains tightly sealed while operating your taillight.

SUPPORT

If you experience difficulties during product installation or operation, NiteRider® provides free telephone support on weekdays from

  • 8:00 am to 4:30 pm (Pacific Time) at
  • 800.466.8366, Ext 4.
  • You may also e-mail us at

WARRANTY
NiteRider® stands behind its products with the following warranties:

  • Lifetime warranty: Covers any defects in material and workmanship, mechanical components (housings, covers, mounts and fasteners) and LEDs
  • 2-year warranty: Printed circuit boards, switches, and AC adapters
  • 1-year Warranty: Rechargeable battery cells

To obtain warranty service have your original sales receipt. Contact the NiteRider® Customer Service Department at 800.466.8366, Ext. 4 to obtain a Return Merchandise Authorization (RMA) number. The RMA number must be prominently displayed on the outside of your package. The product must be properly packaged to prevent damage in transit.

For International customers, please contact your

local NiteRider® Distributor. Go to:

For complete warranty information, please visit our website at

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals