ARLEC 45A 2 Gang DP Cooker Switch Instruction Manual
- July 16, 2024
- ARLEC
Table of Contents
Wiring Instruction
45A Cooker Switch with 13A Socket
TO LOAD
FROM POWER SUPPLY
WIRING INSTRUCTIONS
Read these instructions before you begin the installation; keep the
instructions in safe place for future use.
SAFETY INSTRUCTIONS
This product should be installed by a competent person (e.g. a qualified electrician) in accordance with these instruction and the relevant clauses of the current edition of the IEE Wiring Regulations (BS 7671: Requirements for Electrical Installations) and appropriate statutory regulations.
-
Switch OFF the mains supply at the switchboard and make sure installation circuit is isolated before commencing installation. Ensure no one else has access that would enable the supply to be inadvertently reconnected.
-
It is essential that all connections are made as shown below, that cables are not stressed and that terminal screws are fully tightened.
-
All accessories where a earth terminal is present must be correctly earthed. To do so fix the earth wire to the earth terminal on the accessory or on the metal plate and then connect the short length of the wire from this terminal to the
terminal provided in the mounting box. -
To prevent fire hazard do not exceed the rated current.
-
The layout of the accessory may change from product to product, please check the termination marking engraved on the unit before you proceed with the wire termination.
WARNING : Do not install on freshly plastered or damp walls as this may cause tarnishing.
INSTALLATION
- Partially unscrew all the terminal screws to which the cables are terminated.
- Some accessories have fixing screws clipped to the rear of the plate, unclip these screws before you begin installation.
- For accessories that come with a decorative clip-on front plate, the plate must be removed by carefully sliding the screw driver between the ramp of the main body of the products and the notch in the lower edged of the plate. The plate can then be levered away from the main body of the product.
- Ensure the back box is firmly fixed to the wall / ceiling before you commence installation.
- If using the accessory as a replacement, remove the existing accessory from the wall.
- Inspect the mounting box (wall box) and remove if any plaster debris or dust present.
- Strip the outer sheath on all the cables, then trim wires to appropriate length to allow the cable ends to reach the terminals.
- Strip back the inner insulation of both cables to expose 10mm of wire.
- If using a Neutral wire as a Live or Switched Live, Brown sheathing must be put over the Black or Blue insulation to indicate its change of use.
- Connect the cables as shown in wiring diagrams below.
- Colour codes used in the UK: As from 1st April 2004 new installations in the U.K. could be wired using new EU harmonised colours for the supply conductors of twin and earth cable:
New Colours| Old Colours
---|---
BROWN-LIVE| RED-LIVE
BLUE-Neutral| BLACK-Neutral
Earth GREEN/YELLOW
(The old colours have been replaced from 1st April 2006).
• For accessories having one or more earth terminal, either one or all of
these terminals can be used.
• Push all the wires back into the back box, ensuring the cables are not
trapped or pinched. Fix the product to the back box with the fixing screws
provided. Do not over tighten.
• For accessories that come with a decorative clip-on plate, place the plate
over the mounted accessory and apply finger pressure down the bottom centre
where the notch is present.
NEON INDICATOR
Before the accessory is screwed to the wall, if a neon is present, check that
the neon leads are pushed into their locations on the rear of the product.
Neon leads are not colour coded, as it does not matter which way round they
are fitted.
SPECIFICATIONS
TERMINAL CAPACITY:
1174GB 1x16mm² , 1x10mm² , 2x6mm² , 3x4mm²
MOUNTING
Mounting box minimum depth 47mm.
CLEANING
Clean the front plate with a dry lint free soft cloth. Do not use abrasive or domestic cleaners.
DISP0SAL INSTRUCTIONS
Dispose of the product in an environmentally friendly manner when you decide
to part with it.
This device should not be disposed of with household waste. Dispose of it at a
recycling centre, check with your local authority or retailer for recycling
advice. Please note that all products with this symbol below must be recycled.
WARRANTY
Products are protected by warranty against manufacturing defects for a period
of 12 months from the date of purchase or delivery, including against defects
in production, materials and workmanship.
In the event of a problem with the product within the warranty period please
return it to your nearest store. If the item is shown to have an inherent
defect present at the time of sale the store will, at its discretion, provide
you with a replacement. If we are unable to repair or replace a defective
product, we will refund the purchase price of the defective product in part or
in full.
This warranty does not cover the product where the fault is due to you or any
third parties misuse, abuse, neglect, use in contravention of any oral or
written instructions as to the storage, installation, commissioning, use or
maintenance of the product, or where the product has been the subject of
unauthorised modifications or alterations without our prior written consent,
including the use of unauthorised spares, or has been the subject of
commercial use. For the avoidance of doubt, the exclusions in this paragraph
apply to any defect arising as a result of fair wear and tear, willful damage,
negligence or abnormal working conditions, or where products differ from their
description as a result of changes made to ensure they comply with applicable
statutory or regulatory standards.
The terms of this warranty shall apply to any repaired or replacement product
we supply and the 12 month warranty period is treated as continuing as if the
repaired or replacement product was supplied at the original date of purchase.
Your statutory rights remain unaffected and nothing in this warranty shall
limit or exclude our liability for any rights you have under the Consumer
Rights Act 2015. If any part of this warranty is deemed unenforceable
(including any exclusion of liability) the enforceability of any other parts
of this warranty will not be affected.
Please retain for future reference.
Arlec Electrical Company Limited
Arlec’s telephone number, address and email address are:
Customer Service Contact: 0800 112 0275
Unit 18, Cromwell Business Park, Howard Way,
Newport Pagnell, Buckinghamshire, MK16 9QS
Email: custservice@arlec.co.uk
© This instruction leaflet is subject to copyright and must not be reproduced,
copied or otherwise used in any way or for any purpose without the consent in
writing of the owner, Arlec Electrical Company Limited.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>