V I V O MOUNT-E-WM075-W Electric Swing TV Wall Mount Instruction Manual

July 16, 2024
V I V O

V I V O MOUNT-E-WM075-W Electric Swing TV Wall Mount

Product Specifications

  • Product: Electric Swing TV Wall Mount
  • SKU : MOUNT-E-WM075/W
  • Weight Capacity : 110lbs (50kg)

FAQ

  • Q : What should I do if I am missing a part?
  • A : If any parts are missing or received damaged, please contact our customer support within 30 days of product delivery for a replacement at no cost.
  • Q : What is the weight capacity of the TV wall mount?
  • A : The weight capacity of the TV wall mount is 110 lbs (50kg). Do not exceed this weight limit to avoid serious injury.

CAUTION

If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

  • WARNING: CHOKING HAZARD SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
  • DO NOT EXCEED WEIGHT CAPACITY FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.

Tools Needed:

Weight Capacity

User Guide

Package Contents

Included Hardware & Tools

Assembly & Installation

  • STEP 1
    Temporarily plug Power Cord (F) into Mount (A) and then into an AC outlet
    While holding the Mounting Arm, use Remote (G) to unfold the Mounting Plate until it is 90 degrees to the arm. Then remove the Power Cord.

  • STEP 2
    Using a Phillips screwdriver, remove the mounting arm screws.

  • Calculate the Length of AdjustmentMeasure the length of the TV and put the measurement into the following calculation.
    A sample equation using a 43” TV as an example 43” ÷ 2 + 13” = 34.5”

  • Adjust the length of the Mounting Arm according to the Adjusted Length (X) determined in the calculation

  • Reinstall the mounting arm screws

  • STEP 3

  • Option 1: Wood Stud Mounting

  • Use a studfinder to locate the stud in the wall where you will mount the assembly. Place Template (B) over the stud and use Level (T-B) to align, and mark drilling locations

  • Remove Template (B) and drill 2.2” (55mm) deep holes using a 3/16” (4.5mm) drill bit.

  • Wood Stud – cont’d
    Insert one ST6.3×55 Screws (W-A) into the top-middle hole, leaving 7mm of threads exposed.

    • Slide Mount (A) onto the screw.
  • Secure to the wall using ST6.3×55 Screws (W-A) and M6 Washers (W-C).

Option 2: Concrete/Brick Wall Mounting

Place Template (B) on the wall in the desired location and use Level (T-B) to align, and mark drilling locations

Remove Template (B) and drill 2.4” (60mm) deep holes using a 3/8” (10mm) drill bit.

Concrete/Brick – cont’d
Insert Concrete Anchors (W-B) into predrilled holes. Insert one ST6.3×55 Screws (W-A) into the top middle anchor, leaving 7mm of threads exposed.

  • Slide Mount (A) onto the screw.

  • Secure to the wall using ST6.3×55 Screws (W-A) and M6 Washers (W-C).

  • STEP 4
    Assemble Top Cover (D) and Bottom Cover (E) to Mount (A).

  • STEP 5
    Assemble Top Cover (D) and Bottom Cover (E) to Mount (A). Using a Phillips screwdriver, loosen the safety screws on the back of VESA Brackets (C).

  • STEP 6
    Attach the VESA Brackets (C) to the back of the TV using Screws (M-A through M-D), M8 Washers (M-E) and Spacers (M-F, M-G).

  • STEP 7
    Hang VESA Brackets (C) over Mount (A). Tighten safety screws on VESA Brackets to secure in place

  • STEP 8
    Hang VESA Brackets (C) over Mount (A). Tighten safety screws on VESA Brackets to secure in place. Level the TV by adjusting the leveling screws ontop of VESA Brackets (C) using 4mm Allen Wrench (T-A) and Level (T-B).

  • STEP 9
    Use Straps (H) to organize cables

  • STEP 10
    Use Straps (H) to organize cables. Plug Power Cord (F) into Mount (A) and then into an AC outlet. Use Remote (G) to operate.

Remote Control

Setup & Use

REMOTE | OPERATION INSTRUCTIONS

Pairing the Remote

  1. Use a thin tool (such as a paperclip) to press the Pairing Button on the side of the Mount. The Mount will beep once.
  2.  Press the SET button on the Remote within 3 to 5 seconds after the Mount beeps. The Mount will beep repeatedly for 10 seconds to indicate that the remote is being programmed to the Mount. When the beeping has stopped, the Mount will be ready for operation.

Operation

  1. Use the left and right buttons to begin the in-and-out swinging movement.
  2. When the Mount has reached the desired position, press the button to stop the movement

Save and Recall Memory

To save a certain location to memory, press and hold the mem1 or mem2 buttons for 2 seconds. The Mount will beep, indicating the position has been saved to memory. To recall memory locations, press the 1 or 2 button. The TV mount will automatically adjust to saved memory locations 1 or 2.

Switch Remote Direction

To switch the remote direction, press and hold the up button for 5 seconds and wait for the Mount to beep

Pairing a Remote to Multiple Units

The included Remote may be paired to multiple units, allowing all installed mounts to be Unpairing remote controlled simultaneously. Follow the steps outlined on page 20 in “Pairing the Remote” for each for each remote individually

Unpairing Remotes

To unpair all Remotes, press and hold Pairing Button for 10 seconds. The Mount will beep once initially, and then again after 10 seconds. Upon hearing the second beep, the Remotes will be unpaired. At this time you can re-pair your Remote using the instructions under “Pairing the Remote” on page 20

Reset Mount

If the TV Wall Mount operates abnormally, it may be necessary to perform a reset of the Mount. To reset the TV wall mount, unplug the Mount from power for 10 seconds and plug back in. Hold the button for 6 seconds to return Mount to the minimum (folded) position

Troubleshooting

Standard Troubleshooting

help@vivo-us.com

EXPLORE MORE AT VIVO-US.COM
We offer a wide array of home & office products to fit your needs. From height adjustable desks to monitor mounts to keyboard trays and more

WHO WE ARE
VIVO is more than a brand of ergonomic office furniture. We are a team of creative and innovative individuals working together to offer high-quality, affordable ergonomic solutions. We think and work outside of the box to serve you, our customer, to the best of our ability

Need Assistance?

We Would Love to Help!

Personable Customer Support | Mon-Fri 7am-7pm We offer immediate assistance with rapid response times from customer service agents and product technicians to help you every step of the way

contact

Assembly Video & Product Info
www.vivo-us.com/products/mount-e-wm075

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

V I V O User Manuals

Related Manuals