Hanwha Vision ANE-L6012R Network Camera User Manual
- July 10, 2024
- Hanwha Vision
Table of Contents
Hanwha Vision ANE-L6012R Network Camera
Important Safety Instructions
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Do not install the product in a place exposed to direct sunlight or near heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- This product is designed for use in a network environment with a PoE (Power over Ethernet) connection. Do not connect the product to a power source that does not comply with the specifications of the product.
- Do not install the product in a place where it may be exposed to water or moisture.
- Do not install the product in a place where it may be exposed to dust or dirt.
- Do not install the product in a place where it may be exposed to chemicals or gases.
- Do not install the product in a place where it may be exposed to vibration or shock.
- Do not install the product in a place where it may be exposed to electromagnetic interference.
- Do not install the product in a place where it may be exposed to radio frequency interference.
- Do not install the product in a place where it may be exposed to extreme temperatures.
Warning
- To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
- Do not insert any metallic objects into the ventilation openings or other parts of the apparatus.
- Do not place any objects filled with liquids, such as vases, on the apparatus.
- To avoid injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
Precaution
To reduce the risk of electric shock, do not remove the cover (or back). No user-serviceable parts inside. Refer servicing to qualified service personnel.
Explanation of Graphic Symbols
A triangle with a lightning bolt and arrowhead inside is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
A triangle with an exclamation point inside is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Specifications
| Component | Specification |
|---|---|
| CPU | Intel Core(TM) i7 or 3.4 GHz or higher |
| RAM | 8 GB or higher |
| Recommended Browser | Chrome |
| Compatible Browsers | Chrome, Safari, Firefox, MS Edge (Chromium-based) |
| Supported OS | Windows, Mac, Linux, Android, iOS, Chrome |
| Verification Environment | Windows 10: Google Chrome version 80 or later, |
Firefox version 72 or later, MS Edge version 83 or later
Mac 10.13/10.14| Safari version 11.1.0 or later
Recommended Specifications for NAS (Only for Model ANE-L7012R)
For this camera, it is recommended to use a NAS unit with the following manufacturer specifications. Recommended products: QNAP NAS, Synology NAS.
Recommended Micro SD/SDHC/SDXC Memory Card Specifications
| Specification | Details |
|---|---|
| Recommended Capacity | 16 GB to 512 GB (MLC or 3D TLC type required) |
| Recommended Manufacturers | SanDisk, Transcend, Samsung |
| Product Type | High endurance, Pro endurance |
| Compatibility | Varies by manufacturer and card type |
Components
Check if the camera and accessories are included in the product package. (Due to different sales regions, accessories may vary.)
| Item | Quantity | Description |
|---|---|---|
| Camera | 1 | |
| Quick Guide | 1 | Product installation guide |
| Template | 1 | Product installation guide |
| Torx L Wrench | 1 | Used to open the micro SD slot cover |
| Waterproof RJ45 Accessory | 1 | Used for installation in humid places |
Optional Accessories for Installation
For easier installation, you can purchase the appropriate optional accessories available.
| Model Name | Rear Box | Other Components |
|---|---|---|
| ANE-L6012R/L7012R | SBV-A14B | SBP-125HMW (Hanging Mount), SBP-125MWV (Wall |
Mount), SBP-300CMW/MWM1 (Ceiling Mount), SBP-300PMW1 (Column Mount), SBP- 300KMW1 (Corner Mount), SBP-300BWM (Wall Mount Base), SBP-300NBW (Installation Box)
View
Appearance
| Element | Description |
|---|---|
| Head | The part containing the lens and internal body. |
| Intermediate Cover | A cover that fixes the position after the head direction |
is adjusted.
Components
| Element | Description |
|---|---|
| Reset Button | This button restores the camera’s default settings. Hold it down |
for about 5 seconds to reset the system.
Micro SD Card Slot| Memory card compartment for Micro SD.
Inner Cover| Protective cover for the main body.
PoE Connector| Connects to the network and supplies power via the Ethernet
cable.
Installation
The camera is water-resistant and complies with IP67 standards. However, the female connector connected to the external cable is not. It is recommended to install this product below the edge of the eaves to prevent the cable from being exposed to the outside.
Precautions Before Installation
- Install in a location (ceiling or wall) that can support 5 times the weight of the camera, including the installation bracket.
- Loose or uninsulated cables can cause damage to the product or a fire.
- For safety reasons, keep everyone away from the installation site.
- If the product is subjected to excessive force, it may be damaged due to improper handling. As a precaution, store personal belongings separately.
Disassembly
- Hold the camera body with both hands as shown in the image and use your thumbs to turn the base slot counterclockwise and unlock the intermediate cover.
- Lift the intermediate cover to remove it.
How to Connect the Waterproof RJ45 Cable to a LAN Cable
- Insert the cable in the direction of the arrow.
- Connect the LAN connector (male) to the cable.
- Connect the modular RJ45 socket (female) to the RJ45 connector (male).
- Install by turning the modular RJ45 socket (female) and the RJ45 protection cover to the right (follow the arrow).
- Install by turning the RJ45 protection cover and the rear cover to the right (follow the arrow). When the rear cover is installed, the cable’s waterproof seal is firmly connected to make it waterproof.
Specifications
| Component | Specification |
|---|---|
| Ethernet Connector | RJ45 |
| Transmission Distance | 100 m |
| Standard | IEEE 802.3af |
| Observation | 10/100 Mbps, DC Resistance ≤ 0.125 Ω/m |
Network Connection
Direct Connection to a Local Area Network
Connect the camera directly to the local area network.
Direct Connection of the Camera to a DSL/Cable Modem Based on DHCP
Connect the camera directly to a DSL/cable modem based on DHCP.
How to Use Device Manager
Use the Device Manager to configure the camera settings.
Automatic Camera Search
Automatically search for the camera on the network.
How to Configure the IP Address
Configure the IP address settings for the camera.
How to Register the Camera Manually
Manually register the camera on the network.
Automatic IP Configuration
Automatically configure the IP settings for the camera.
Port Forwarding Configuration
Configure port forwarding settings for the camera.
Connecting to the Camera from a Local PC
Connect to the camera from a local PC.
Connecting to the Camera from a Remote PC via the Internet
Connect to the camera from a remote PC via the Internet.
Web Viewer
Connecting to the Camera
Connect to the camera using the web viewer.
Password Configuration
Configure the password settings for the camera.
Login
Log in to the camera using the web viewer.
Web Viewer Configuration
Configure the web viewer settings for the camera.
Appendix
Troubleshooting
Check to ensure all network cables are properly connected.
Verify all network connections if the viewer disconnects during control.
If no image appears, check the settings in the following sequence: network connection, camera settings, and web viewer settings.
If the Micro SD card cannot record, reformat the card in the camera’s settings menu.
If the NAS cannot record, check the NAS settings and network connection.
FAQs
How do I reset the camera to its default settings?
Hold the reset button for about 5 seconds to restore the camera's default settings.
What should I do if the camera does not connect to the network?
Check all network cable connections and verify the network settings.
How do I configure the IP address for the camera?
Use the Device Manager to configure the IP address settings for the camera.
What should I do if the camera does not record on the Micro SD card?
Reformat the Micro SD card in the camera's settings menu.
How do I connect to the camera from a remote PC?
Use the web viewer to connect to the camera from a remote PC via the Internet.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>