baseus C02 Pro Magnetic Wireless Charging Car Mount User Manual

baseus C02 Pro Magnetic Wireless Charging Car Mount

Baseus Packaging Design Information

paper, single-sided color printing, 65g packaging paper, 82x82mm, single-sided monochrome printing, OP/ROHS
Packaging Surface Design| Yang Fan
Packaging Structure Design| Zhang Qing

Version History

number POA0 updated to POA1

Contact Us

Email: care@baseus.com

Website: https://www.baseus.com

Phone: +1 800 220 8056 (US)

Customer Service

• EN: 1. 24-Month Warranty 2. Lifetime Tech Support

Product Specifications

Installation Instructions

Recommend use scenario: center console/dashboard/behind the control panel.

1. Please wipe the surface with the alcohol pad and keep it dry and clean before you apply the 3M tape;
2. Peel off the 3M tape and stick the Velcro base to the center console/dashboard/behind the control panel, and wait for 2 hours;
3. Stick the Velcro on the holder to the base and bend the handle part to the angle you want.

Illustrations:

• Image showing the wiping of the surface with an alcohol pad.
• Image showing the application of 3M tape to the center console/dashboard/behind the control panel.
• Image showing the sticking of Velcro on the holder to the base and bending the handle part to the desired angle.

Attention

1. This product is applicable to iP12 and above models, older iP models and Android models need to use with the metal plate;
2. Use with the phone case will affect the magnetic attraction, you can stick the metal plate to the phone cases;
3. Make sure the surface is clean and dry before you stick the 3M tape to it;
4. After you stick the 3M tape, wait for 2 hours;
5. The handle part can withstand 200 bends, please avoid bending too many times in a short period of time;
6. Please avoid 180 degree bending.

FAQ

What models is this product compatible with? This product is compatible with all models, but older iP models and Android models need to use the metal plate. What is the wireless charging output? The wireless charging output is 5W/7.5W/10W/15W. What should I do before applying the 3M tape? Please wipe the surface with the alcohol pad and keep it dry and clean before you apply the 3M tape. How long should I wait after applying the 3M tape? Wait for 2 hours after applying the 3M tape. Can I use this product with a phone case? Yes, but using it with a phone case will affect the magnetic attraction. You can stick the metal plate to the phone cases.

This symbol indicates that this product shall not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Follow local rules and never dispose of the product with nonnal household waste.

Declaration of Conformity

Shenzhen Baseus Technology Co., Ltd. declares that the product is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
https://eu.baseus.com/pages/euro-compliance

The product has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
The following importer is the responsible party.

Company Name: BASEUS TECHNOLOGY (US) INC Address: 421 S BROOKHURST ST SUITE 1312 ANAHEIM, CA 92804
Telephone: 6145412699

FCC

This device complies with part 15 of the FCC Rules. Operation is subject the following two conditions: (1) this device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are desto provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to raddio communications However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the useris encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Frequency range: 115kHz-205kHz
Field strength: -16.56 dBuA/m@10m
This product can be used across EU member states.
FCC ID: 2A482-BSCM019

Manufacturer: Shenzhen Baseus Technology Co., Ltd.
Add: 2nd Floor, Building B, Baseus Intelligence Park, No.2008, Xuegang Rd, Gangtou Community, Bantian Street, Longgang District, Shenzhen
Executive Standard: XXXXXXXX
Hotline: 400-071-2711 (China) / +1 800 220 8056(Global)
Website: https://www.baseus.cn(China) / https://www.baseus.com(Global)
Official After-sales E-mail Address: service@baseus.com (China) / care@baseus.com (Global)
PB4276-P0A1
1100003296
14Rizit/Designed by Baseus
ME#*/Made in China

Warning Please follow the above safety instructions otherwise it will cause fire, electric shock, damage or other injuries.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>