Mac Faucets TiO-32, TiO-34 Faucet and Soap Dispenser in One Installation Guide

: July 8, 2024
: MAC FAUCETS

Table of Contents

TOOLS NEEDED
WIRE CONNECTION
PARTS
SOAP REFILL INSTRUCTIONS
BATTERY REPLACEMENT INSTRUCTIONS
GALLON CONTAINER INSTALLATION
AVAILABLE WASHROOM ACCESSORIES
OTHER MODELS
LIMITED WARRANTY
CUSTOMER SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Mac Faucets TiO-32, TiO-34 Faucet and Soap Dispenser in One

TOOLS NEEDED

WIRE CONNECTION

PARTS

Insert faucet shank through sink hole
Place washer and lock nut onto shank
Tighten lock nut
Mark holes for valve and install on the wall, follow instructions on label
Connect cold supply line
NOTE: Drain the water line before the hose is connected

Optional Mixing Valve
NOTE: Drain the water lines before the hoses are connected

Connect faucet hose

Align marks located on solenoid plug and push firmly. Power plug does not require alignment, Plug and push firmly.
Make sure no objects are present in the sink when plugin cables. After plugin cable, wait one minute before placing anything in the sink. Test for leaks before using faucet

Connect the solenoid valve (D) plugs. Connect the Power supply (C) plugs. Open the water supply and check for leaks

Soap Pump Installation
Mount wall bracket onto wall in a level horizontal position. Follow arrows showing UP side.

Install pump housing onto wall bracket (insert AA into BB and push enclosure down).

1. Before proceeding to step 9 make sure soap bottle is filled with liquid soap. See page 6 for soap refill instructions
  Press and hold the primer button located on the underside of the pump housing until soap pours out of nozzle

SOAP REFILL INSTRUCTIONS

DO NOT USE HEAVY CREAM SOAPS OR GRIT TYPE SOAPS

It is best to use same brand of soap every time, and not to let dispenser remain dry for to long

Unscrew the empty bottle
Add liquid soap into the empty bottle
Affix bottle filled with soap onto pump housing. Do not overtighten

BATTERY REPLACEMENT INSTRUCTIONS

Unfasten 2 cover screws,and lift cover up and away from batteries
Properly place new batteries inside of battery case
Place cover back onto battery case and fasten 2 cover screws

GALLON CONTAINER INSTALLATION

NOTE: GALLON CONTAINER MUST BE PLACED ON LEVEL SURFACE CAPABLE OF SUPPORTING 10LB WEIGTH OR GREATER

Mount wall bracket onto wall in a level horizontal position. Follow arrows showing UP side.
Place the gallon container against the wall underneath the bracket.
Insert the smaller diameter of the coupling into the threaded side of the pump, then insert the adapter to the coupling

NOTE: Coupling and adapter are used only for Gallon Container

Install pump housing onto wall bracket (insert AA into BB and push enclosure down), insert the adapter onto the fitting of the lid at the same time
1. Remove the plug for refill Put back after refill

AVAILABLE WASHROOM ACCESSORIES

TiO-324
Two-in-one Automatic Faucet and Soap Dispenser (with 4” riser for high vessel sink
TiO-344
Two-in-one Automatic Faucet and Soap Dispenser (with 4” riser for high vessel sink)
ADA Grab Series
Models GB-18, GB-36 and GB-42
ATD-10
Automatic Towel Dispenser
AAD-12
Automatic Aroma Dispenser
ASD-13
Automatic Soap Dispenser
TH-2
Tissue Holder
SCD-4
Toilet Seat Cover
HD-5
Automatic Hand Dryer

OTHER MODELS

Model TiO-32
Model TiO-34

LIMITED WARRANTY

Mac Faucets warrants this product to be free of defects for a period of one year from date of purchase. Mac Faucets will replace, free of charge, during this warranty period, parts that prove defective when properly installed and under normal use and service. Damage that occurs as a result of abuse, improper installation, environmental conditions, or improper application will void this warranty. Products must be shipped with postage and handling prepaid, along with dated proof of purchase. This warranty does not cover installation or any other labor charges. It does not cover shipping and handling of both replacement parts and returned defective parts. Products or components that have been altered, or in any way modified, will not be covered under this warranty. Replacement parts are under warranty only for the remaining period under the initial warranty. Some states do not allow for exclusion of incidental or consequential damage.