GE Profile PTDS650GM 7.0 cu. ft. Stainless Steel Capacity Gas Dryer Owner’s Manual

GE Profile PTDS650GM 7.0 cu. ft. Stainless Steel Capacity Gas Dryer

Specifications:

• Model: GE PTDS650GM0WT
• Capacity: 7.0 cu. ft.
• Material: Stainless Steel
• Power Source: Gas
• Electric Rating: 120V, 60Hz, 6A
• Gas BTU/HR: 22,000

Product Usage Instructions

PTDS850GM/PTDS855GM GE Profile Harmony™ 7.3 Cu. Ft. Stainless Steel Capacity Gas Dryer

Installation Instructions:
The dryer should be properly grounded with the correct power supply. Ensure proper exhaust options are set up according to the unit’s requirements. It is essential to follow the installation instructions provided with the dryer for correct setup.

Venting Information:
Ensure the dryer is properly exhausted to the outside. Do not terminate exhaust in hazardous areas like chimneys, enclosed spaces, or attics. Use a dampered wall cap for termination to prevent back drafts and nesting. Call 1-800-GE-CARES for more information on venting kits and accessories.

Special Installation Requirements:
Adhere to the National Electric Code and National Fuel Gas Code when installing the dryer. Use metal ducts for proper exhausting and follow the guidelines provided for optimal performance.

Dimensions and Installation Information (in inches)

• Exhaust Options: When viewed from the front of the unit, exhaust 3-way via rear, left and bottom. Dryer is shipped exhausted to the rear. Alternate exhausting knockouts are supplied. Left or bottom exhaust requires a conversion kit.
• Gas: An individual properly-grounded branch circuit, with a three-prong groundingtype receptacle, protected by a 15 or 20 amp circuit breaker or a time-delay fuse is required.
• Gas Dryer Electric Rating: 120V, 60Hz, 6A
• Gas (BTU/HR): 25,000. Factory-equipped for natural gas. Tested for LP gas. LP gas supply requires a conversion kit. Check installation instructions for correct kit and have a qualified gas technician install a conversion kit. See dryer ducting information for proper installation.
• Note: Dryer wall outlet must be located within 36″ of service cord entry and accessible when dryer is mounted in position. Installation Information: For complete information, see installation instructions packed with your dryer.

For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000.
For complete information, see installation instructions packed with your dryer.

Ducting Materials

For best performance, this dryer should be vented with 4″ diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semirigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil- type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting. Exhaust Length Calculation:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer, add one turn.
2. The maximum length of 4″ rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.

Dryers must be exhausted to the outside.

Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard. Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12″ above the ground or any other obstruction with the opening pointed down. Dryer Elbow Kit, Pub. No. 14-A003 is available at additional cost. For use with side or bottom exhaust options.

For more information on venting kits and accessories, please call 1-800-GE- CARES.

Special Installation Requirements

• Alcove or Closet Installation:
  • If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
  • The dryer MUST be exhausted to the outside.
  • Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
  • 0″ either side; 3″ front and rear
  • Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.
  • Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.
  • No other fuel-burning appliance shall be installed in the same closet with a gas dryer.
• Bathroom or Bedroom Installation:
  • The dryer MUST be exhausted to the outdoors.
  • The installation must conform with the local codes, or in the absence of local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
• Minimum Clearances other than Alcove or Closet Installation:
  • Minimum clearances to combustible surfaces are: 0″ both sides; 3″ rear

Dryer Exhausting Information: Use metal duct only, vertical and horizontal ducting.

Features and Benefits

• Steam Refresh/Steam Dewrinkle – Steam Refresh helps reduce wrinkles, odors and rejuventates fabrics, while Steam Dewrinkle reduces wrinkles and freshens clean clothes
• Sensor Dry Plus™ – Innovative moisture-sensing technology helps maintain quality
• Duct sensing – Provides an alert when ducting needs to be cleaned
• Antibacterial cycle – Reduces certain types of bacteria by 99.9%
• Specialty cycles – Pre-set cycles are designed to provide superior care for specific items such as jeans and towels & sheets
• LED electronic controls with cycle countdown display – Designed to simplify cycle selection and provide accurate cycle times
• Speed Dry – Quickly dries items and small loads for families on the go
• My Cycles – Custom cycle that can be set for specific or frequent needs
• Delicate cycle with low-heat setting – Low-heat setting and gentle wash cycle help protect delicate garments
• Deluxe dryer rack – Allows tumble-free drying of items like sneakers and stuffed animals
• Model PTDS855GMMS – Metallic Silver
• Model PTDS850GMWW –White on white

FAQ

Q: What type of gas does the dryer come factory-equipped for?
A: The dryer is factory-equipped for natural gas, but it has been tested for LP gas. A conversion kit is required for LP gas supply.

Q: What should I do if my dryer wall outlet is not within 36 inches of the service cord entry?
A: Ensure the dryer wall outlet is located within 36 inches of the service cord entry and is accessible when the dryer is mounted in position. If needed, use appropriate extensions or adjustments to meet this requirement.

Q: Can I terminate the exhaust into a common duct with a kitchen exhaust?
A: No, it is not recommended to terminate the exhaust into a common duct or plenum with a kitchen exhaust as it could create a fire hazard due to lint and grease accumulation.

References

• GE Companies: Next Generation and Future | General Electric
• Repair Your Grill: Shop Replacement Parts for 24,880 Models
• Ge Dryer Parts - Select From 3387 Models

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>