Linkind LC2300284 4 Key Remote Control User Manual

Linkind LC2300284 4 Key Remote Control

Product Specifications

• Model: 18A
• Power: 8V
• Weight: 2kg
• Dimensions: 10 x 5 x 3 inches

Product Usage Instructions

Step 1: Power On
To start using the product, ensure it is properly connected to a power source and turn it on using the power button.

Step 2: Setting Up
Follow the on-screen prompts or refer to the user manual for initial setup instructions. Adjust settings as needed.

Step 3: Product Operation
Once set up, you can now use the product for its intended purpose. Refer to the user manual for specific functions and features.

Frequently Asked Questions

• Q: How do I clean the product?
  

  • A: Use a damp cloth to gently wipe the exterior of the product. Do not use harsh chemicals or abrasive materials.

• Q: What should I do if the product malfunctions?
  

  • A: Refer to the troubleshooting section of the user manual for common issues and solutions. If problems persist, contact customer support.

User Manual 4-Key Remote Control

Product introduction

Operational guideline

How to Pair Your Remote Control (e.g., Smart Plug)

1. Activate Pairing Mode on the Remote Control
   • Press any button on the remote control three times until the red light starts blinking. This indicates that the remote control is in pairing mode. ( The button pressed is the button for this pairing)
   • Tip: The remote control will remain in pairing mode for up to 60 seconds. To cancel pairing, press the pairing button briefly.
2. Activate Pairing Mode on the Plug
   • After plugging in the device, press and hold the button on the plug for 5 seconds. The green and yellow lights will flash alternately, indicating that the plug is now in pairing mode.
3. Confirm Successful Pairing
   • When the green light on the plug flashes twice and then returns to its normal state, the pairing is successful.
   • Tip: Ensure the remote control and the plug are within 1 meter of each other and complete the pairing within 1 minute.

How to Unpair Your Remote Control (e.g., Smart Plug)

1. Activate Unpairing Mode
   • Press and hold buttons 1 and 4 simultaneously for 5 seconds to unpair all keys on the remote control.
2. Confirm Successful Unpairing
   • The plug will blink twice and then return to its normal state, indicating that the unpairing process is complete.
   • Tip: The unpairing process should be completed within 60 seconds. To cancel the unpairing command, press any button during this period.

Additional Recommendation
If your plug is already connected to the AiDot app, the paired remote control will automatically connect to AiDot as well. For the best experience and to enjoy a comprehensive loT ecosystem, we strongly recommend downloading the AiDot app.

Quick Start Guide

Step 1: Download the App on App Store or Google Play.

Google, Google Home and Google play are trademarks of Google LLC.

Step 2 : Create an account and sign in.
Step 3 : Press ‘+’ button to add the device.

Step 4 : Follow the instructions on App.

Troubleshooting and FAQS

1. Factory default
   • Insert to pin hole (g) for 3 seconds to trigger the reset button (h) without removing the battery covering(j) to reset the remote control to factory default.
2. Low power notification and Replace the battery
   • Indicator (a) blinks five times notifies that the battery is low. Remove the battery covering (j) by screwdriver.
   • Remove the battery covering(j) by screwdriver.
   • Use at blade screwdriver to pry out the battery o be replace. Install a new 3V CR2450 battery (i) .Replace the battery covering (j) on the remote control.
3. The remote control cannot pair with the plug.
   • The pairing distance is too far, please perform the pairing operation within 0.5m
   • If the pairing exceeds the specified time for 1min, please follow the matching operation steps again.
4. The remote control cannot unpair the plug.
   • The pairing distance is too far, please unpair within the range of 0.5m
   • If pairing exceeds the specified imin, please follow the unpairing procedure again

Certification

Safety certification
CE/FCC Certification agreement
BLE Usage Environment Requirements

Operating Temperature :32°F to 104°F (0°C to 40°C) Operating Humidity: Up to 85% non-condensing Storage Temperature: -4°F to 140°F (-20 °C to 60°C) Environmental requirements: RoHS/REACH

FCC Statement

This device complies within part 15 of the FCC Rules Operation is subject to the following two conditions

1. this device may not cause harmful interference and
2. this device must accept any interference received: including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

NOTE: This equipment has been tested and found to comply within the limits for a Class B digital device: pursuant to Part is of the reed kales. Ines limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates: uses and can radiate radio frequency energy and: if not installed and used in accordance within the instructions: may cause harmful interference to radio communications. However: there is no quarantine that interferences will not occur in a particular installation

It this equipment does cause harmful interference to radio or television reception: which can be determined by turning the equipment off and on: the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different, from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction

IC Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions

1. This device may not cause interference and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

ISED 20cm
RF ISED RF Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

Statement

Statement (1)

• Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.”
• Even used batteries may cause severe injury or death.
• Call a local poison control center for treatment information.
• The compatible battery type CR2450.
• The nominal battery voltage 3VDC.
• Non-rechargeable batteries are not to be recharged.”
• Do not force discharge, recharge, disassemble, heat above (manufacturer’s specified temperature rating) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns. Statement (2) :
• Ensure the batteries are installed correctly according to polarity (+ and -).
• Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
• Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

Safety Information
WARNING Keep out of reach of children. This product contains tiny components, which can calf choking or injury if ingested.

WARNING

• Keep batteries away from children. This product contains coin/button cell batteries.
• If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep away from infants and small children at all times.
• If battery is swallowed or placed inside any part of the body, immediately seek EMERGENCY medical attention.
• Battery may rupture if the incorrect type of battery is used. Follow the instructions in this manual.
• Dispose of used battery promptly.

WARNING
Used batteries should be disposed of at an appropriate recycling center. Do not discard with normal household trash. DO NOT BURN.

WARNING

• Any battery has the potential to leak harmful chemicals that can damage skin, clothing or the inside of the alarm. To avoid risk of injury, do not allow any substance leaked from the battery to come in contact with eyes of skin. Any battery has the potential to rupture and may even explode if exposed to fire or other forms of excessive heat. Use caution at all times when handling batteries.
• Do not use rechargeable or reusable batteries.
• Do not allow children to install batteries unsupervised.
• Follow battery manufacturer’s instructions for proper handling, storage and disposal of batteries.

CAUTION

• Do not install
• wet locations.
• Outside the premises (outdoors).
• Near the metal objects and mirrors that cause radio signal attenuation or shading it
• Near the powerful main wiring.

SPRING SUNSHINE TECHNOLOGY CO., LIMITED FLAT/RM 01-04, 24/F, FU FAI COMMERCIAL CENTRE, 27 HILLIER STREET, SHEUNG WAN, HK
Manufacturer: Leedarson loT Technology Inc.
Address: No.1511, 2nd Fanghu North Rd, Huli District, Xiamen, China

Phone: 1-877-770-5727 (Mon.-Fri.9 to 5 PST)
http://www.linkind.com
Email: service@linkind.com

@linkind.lights

@linkindofficial

@linkindofficial

Made in China V1.0

Documents / Resources

| Linkind LC2300284 4 Key Remote Control [pdf] User Manual
LC2300284, LC2300284 4 Key Remote Control, 4 Key Remote Control, Remote Control, Control
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>