VEVOR BH705E Electric Wall Heater User Manual

VEVOR BH705E Electric Wall Heater

Product Information

Specifications

• Model: BH705E
• Type: Electric Wall Heater
• Power Supply: AC 120V 60Hz
• Heating Modes: Comfort mode, ECO mode
• Temperature Range: Comfort mode: 50-95°F, ECO mode: 43-88°F

FAQ

• Q: Can I cover the heater?
  • A: No, in order to avoid overheating, do not cover the heater.
• Q: Can I use the heater in the bathroom?
  • A: No, do not use this heater in the immediate surroundings of a bath, a shower, or a swimming pool.
• Q: How should I install the fixed heater?
  • A: The fixed heater should be installed so that switches and other controls cannot be touched by a person in the bath or shower. Means for disconnection having a contact separation in all poles must be incorporated in the fixed wiring in accordance with the wiring rules.

We continue to be committed to provide you tools with competitive price.
“Save Half”, “Half Price” or any other similar expressions used by us only represents an  estimate of savings you might benefit from buying certain tools with us compared to the major  top brands and doses not necessarily mean to cover all categories of tools offered by us. You  are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our  user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

Safety Advice

READ THIS NOTICE CAREFULLY BEFORE OPERATING THE APPLIANCE.

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards  involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• Children of less than 3 years should be kept away unless continuously supervised.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal  operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.
• CAUTION:  Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
• If the supply cord is damaged, it must be replaced by the manufacturer, its  service agent or similarly qualified persons in order to avoid a hazard.
• CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the utility.
• WARNING: In order to avoid overheating, do not cover the heater.
• The heater must not be located immediately below a socket-outlet.
• Do not use this heater in the immediate surroundings of a bath, a shower or a swimming pool.
• Fixed heaters are to be installed so that switches and other controls cannot be touched by a person in the bath or shower.
• Means for disconnection having a contact separation in all poles must be incorporated in the fixed wiring in accordance with the wiring rules.

THIS PRODUCT IS FOR ROOM HEATING

SAVE THESE INSTRUCTIONS

Spare Parts List

• Fixed screw4, Expansion screws4,Remote control*1

Installation

• Drill holes on the wall according to the instruction inside the box.

Warning: Be sure to keep the safety distances as shown on the above drawing.

• Fit the fasten tube in the hole and fit the bracket on the wall with screws
• Hang the unit on the bracket gently, after ensuring the unit is right fixed, turn the lock in the bracket as picture show.

Warning: Before using the heater, make sure it’s mounted tightly on the wall.

Parts List

CIRCUIT DIAGRAM And Control panel

CIRCUIT DIAGRAM

Control panel

1. Standby: on/off
2. Heating status
3. Comfort mode
4. ECO mode

| Standby
---|---
M| Mode selection
+| Increase function
–| Decrease function
****| Timer

How To Use And Setting

How to use

• Plug the appliance to AC 120V 60Hz socket and press on/off switch in the back cover with a beep sound. The indicator light is on.
• Press to turn on the heater.
• To stop the heater working, press to turn off the heater, the indicator will display, then the heater would blow cool wind around 60 seconds to discharge heat.
• Unplug the product when it’s not in use.

Temperature setting

When the screen display the target set temperature, press + and – to set directly:

• Comfort mode or Comfort mode in P1/P2/P3: Press + and – to set the temperature from 50-95 ℉.
• ECO mode or ECO mode in P1/P2/P3: Press  + and – to set the temperature from 43-88 ℉.

Note: ECO mode=Comfort mode – 7 ℉.

Clock and day of week setting

• Press down 3 secs to enter clock and day of week setting
• The screen display “ d ”, press + and – to select the day from 1-7.

• Press to confirm day setting and enter the clock hour setting, with the screen display: h.
• Press + and – to set the current hour
• Press to confirm hour setting and enter the minute setting, with the screen display: .
• Press + and – to set the current minute
• Press to confirm all settings

Note: The clock and calendar will be reset to factory default if without power supply.

Heating Mode

Press M to enter mode selection. By pressing M , heating mode runs in a continuous cycle as below:

• Comfort mode: Press + and – to set the temperature from 50-95 ℉ oC.
• ECO mode: Press + and – to set the temperature from 43-88 ℉ oC.

Note: ECO mode=Comfort mode – 7 ℉

• Anti-frost mode: the screen display Fr. The target temperature is 45 ℉.
• The temperature can’t be adjusted.
• P1/P2/P3: Pre-set heating program.

Note: If the clock and day setting are not finished, the first time to enter P1/P2/P3 program setting, it is requested to set day and clock setting in advance.

• P1: (Monday-Sunday) Program can’t be set.

• P2: (Monday-Friday) Program can’t be set.
• P2: (Saturday-Sunday) Program can’t be set.
• P3: (Monday-Friday) Adjustable program
• P3: (Saturday-Sunday) Adjustable program

P3 adjustable program setting

1. When under P3 mode, press M over 3 secs to enter day setting.
2. The screen displays d1 , press + and – to set from d1-d7 (Monday-Sunday). Press M to confirm and enter hour setting
3. The screen displays 00 , press + and – to set from 00-23). Press M to choose heating mode for every hour (Comfort mode or ECO mode or anti-frost mode for 2 indicator lights off)
4. Repeat the operation until you have completed the schedule of every hour and every day.

Note: After setting heating mode for hour 23, press + to come back to day setting.
Note: when screen displays d7 , press + finish all setting with display of P3.

Power setting And function

Power setting

Long press M 3 seconds to set working positions, press + and – to change setting as below in a cycle.
Fan mode -H0, half power- H1,or full power -H2.

Timer off function

• Press one time, the screen display “ Oh ” and keeps flashing, keep pressing , the screen will display 2h – 4h – 8h -0h in a cycle. Or press and to set timer from 0-9 hours.

Open window function

• To turn on open window function, press together M and + , the screen will display F0 , after 3 seconds, the screen will display the set temperature.
• To turn off open window function, press together M and -, the screen will display FF , after 3 seconds, the screen will display the set temperature.

SPECIFICATIONS

TROUBLESHOOTING

If the product does not work, please follow the following instructions.

1. Insert the plug of the heater into a suitable socket.
2. Turn on the mechanical main switch of the power supply.
3. Adjust the target temperature to above room temperature.
4. Ensure the tip-over column is suppressed.

CLEANING & MAINTENANCE

• Switch off and unplug from the power supply before cleaning.
• Using a soft, moist cloth, with or without a mild soap solution, carefully clean the exterior surface of the product.
• CAUTION: Allow the product to completely cool before handling or cleaning it.
• Do not allow water or other liquids to run into the interior of the product, as this could create a fire and/or electrical hazard.
• We also recommend the periodic cleaning of this appliance by lightly running a vacuum cleaner nozzle over the guards to remove any dust or dirt that may have accumulated inside or on the unit.
• CAUTION: Do not use harsh detergents, chemical cleaners or solvents as they may damage the surface finish of the plastic components.

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
Imported to AUS: SIHAO PTY LTD, 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
Imported to USA: Sanven Technology Ltd., Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

Technical Support and E-Warranty Certificate: www.vevor.com/support

NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us: CustomerService@vevor.com

Made In China

References

• Contact Us – Official VEVOR Support
• Contact Us – Official VEVOR Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>