ZINC 3334814 Bike Helmet Instruction Manual
- June 3, 2024
- zinc
Table of Contents
3334814 Bike Helmet
CYCLE HELMET
READ THIS MANUAL CAREFULLY AND FOLLOW THE INSTRUCTIONS COMPLETELY
Instruction Manual
Complies with EN 1078:2012+A1:2012
FITTING TO BE SUPERVISED BY AN ADULT.
FITTING YOUR HELMET
The helmet you have just purchased provides protection, whether on or off the
road. To insure proper use of this helmet, familiarise yourself with its
features, fit and care by carefully reading through this manual before wearing
your new helmet.
STEP 1: The helmet fits correctly when the fit pads hold the helmet
firmly but comfortably in place. All fitting adjustments MUST be made with the
helmet in the correct position. Failure to do so will result in a poor fit,
allowing the helmet to move out of position or come off in an accident. For
the correct positioning, please refer to Diagram DIAGRAM A
Always wear the helmet as shown to protect the forehead
STEP 2: The front and rear straps should join at the point slightly below and in front of the ears. See diagram B. To adjust the position of the straps hold one end of the buckle in one hand and slide the slide adjuster up or down as necessary with the other hand correctly positioned. To adjust the front or rear strap individually, hold the strap to be adjusted and slide the slide adjuster in the appropriate direction.
STEP 3: Always wear the helmet with the chin strap buckle fastened and the strap pulled tight. Make sure the strap is well back against the throat, Not on the point of the chin. Straps worn on the point of the chin increase the chance of the helmet coming off in an accident. Diagram C and D show how to fasten and release the buckle.
Diagram E shows the proper placement of the chin strap.
Make sure the loose end of the strap passes through the rubber “0” ring. If it
does not, the strap may slide loose and the helmet can come off accidentally.
See diagram F
STEP 4: Before using the helmet, make sure it fits correctly, the straps
are correctly adjusted and the chin strap is tight enough. Put the helmet on
in the correct position. Fasten the chin strap and pull it tight.
CHECK THE FIT
Grab the helmet with both hands and twist it to the left and to the right. If
the helmet fits, the skin on the forehead will move as the helmet moves. If it
does not, the helmet is too loose. Return to step 1.
CHECK THE STRAPS
Grab the helmet with both hands and try to remove it by rolling the helmet
forward and backward as far as you can. If you can roll it off the head
completely in either direction, roll it forward so far that it blocks vision
or backwards enough to expose the forehead, the fit is not correct. Repeat
Steps 2 – 4 until the helmet movement is minimal.
WARNING: If you cannot adjust the helmet to fit as required by Step 4, DO
NOT USE THIS HELMET. Replace it with a different size. The helmet can only
protect if it fits well and Zinc recommends that you should try different
sizes and choose the size which feels secure and comfortable on the head.
STEP 5: Once you are satisfied that the helmet fits correctly and that
all straps are properly adjusted and tightened, take a short ride. Pay r
attention to overall comfort and helmet stability while riding. Make any minor
adjustments to the fit pads and straps to improve the comfort and stability.
STORING YOUR HELMET
After each use, allow the helmet to air dry and then store in a cool, dry place. Excessive heat can damage the helmet. Direct sunlight, dark sports bags and automobiles can get hot enough to cause heat damage to the helmet. Damaged helmets will appear to have uneven or bubbly surfaces. DO NOT USE A HEAT DAMAGED HELMET.
CLEANING YOUR HELMET
Only use mild soap and water to clean the helmet, straps and pads. DO NOT use
chemicals. Do not use solvents or aggressive cleaning agents.
WARNING!
LIMITED IMPACT PROTECTION
Helmets reduce or prevent many injuries. But, impact forces, even in a common
low speed accident, can result in serious injury or death. Energy absorbing
materials used in helmets crush on impact. Sometimes the blow can crash the
material completely. When this happens some of the force is transferred to the
head. If the force is great enough, it can cause injury or death. Every
accident is different, it is impossible to predict when this might happen.
HELMETS CANNOT PREVENT ALL HEAD INJURIES!
Some head injuries are not caused by impacts at all. They are caused by other
forces. Helmets are designed to protect your skull, but cannot protect your
brain or muscles around the neck, or the spine.
HELMETS CANNOT PROTECT WHAT THEY DO NOT COVER!
A helmet only protects what it covers. It does not protect the neck or any
area of the helmet it doesn’t cover. Always wear a helmet low, in front to
protect the forehead. Make sure the helmet fits snugly and the straps are
adjusted to hold the helmet firmly in place when tightly fastened. WARNING!
This helmet should not be used by children while climbing or doing other
activities when there is a risk of strangulation/hanging if the child gets
trapped with the helmet. A helmet cannot always protect against injury.
HELMETS CANNOT BE MODIFIED
It is dangerous of modifying or removing any of the original component parts
of the helmet other than as recommended by the manufacturer, and that helmet
should not be adapted for the purpose of fitting accessories in a way not
recommended by the manufacturer.
SAFETY INFORMATION
YOU SHOULD ALWAYS:
- Wear your helmet low, in front to protect your forehead from impact.
- Fasten your buckle and tighten your chin strap.
- Check your adjustments every time you wear your helmet.
- Inspect your carefully before each use.
- Replace your helmet immediately when any visible signs of damage appear.
- Clean your helmet with mild soapy water.
- Store your helmet in a cool, dry place.
- Wear a helmet whenever you are participating in your favourite sport.
- Wear a helmet designed for what you are doing.
- Discard or destroy a helmet that has been involved in an accident.
- Think safety!
YOU SHOULD NEVER:
- Wear a helmet that’s been in an accident, even if damage is not visible.
- Loan you helmet to other people.
- Wear someone else’s helmet.
- Wear your helmet with the buckle unfastened.
- Wear your helmet tipped back to expose your forehead
- Wear anything under your helmet.
- Wear the helmet while operating a motor vehicle.
- Clean your helmet with chemical cleaners.
- Store your helmet in hot and damp places.
- Take unnecessary risks just because you are wearing a helmet.
- Modify this helmet in any way.
PARENTS: A helmet is NOT a toy. DO NOT allow children to play with it. They
can damage it or hurt themselves. This helmet is designed to protect impact
cause by collision of head with an obstacle while cycling or roller skating,
it has passed
EN1078:2012+A1:2012 to show conformity to the EHSR of EU 2016/425 (EU only).
EC/EU Type examination conducted by: SGS Fimko Oy, Takomotie 8, 00380
Helsinki, Finland. Notified Body No: 0598.
EUROPEAN TEST APPROVAL STANDARD:
EN1078:2012+A1:2012
SIZE FITS 54-58CM
PRODUCT ITEM NUMBER: 92199 (FCJ-102)
CUSTOMER HELPLINE
Hy-Pro advise you to contact us directly and not to return this item to the
place of purchase. Hy-Pro has taken great care to ensure this item has reached
you in good condition, should you have a query please ring our helpline +44
(0) 800 731 0006 where your call will be dealt with promptly. Alternatively,
please email:
[email protected].
REMOVE ALL THE PACKAGING BEFORE GIVING TO A CHILD.
- PLEASE RETAIN PACKAGING AND MANUAL FOR FUTURE REFERENCE
- COLOUR & CONTENTS MAY VARY FROM THOSE SHOWN ON PACKAGING
www.hy-pro.co.uk
www.zincsports.com
Hy-Pro House, Centrus Park, Arenson Way,
Dunstable, Bedfordshire LU5 5BN. UK
Hy-Pro Europe: Cube Building, Monahan Road, Cork,
T12H1XY – Republic of Ireland.
Documents / Resources
| ZINC
3334814 Bike
Helmet
[pdf] Instruction Manual
3334814, Bike Helmet, Helmet, 3334814, Cycle Helmet
---|---