JOHNSON JLD300-GN2D Cross Line and 2 Dot Laser Level User Guide

JOHNSON JLD300-GN2D Cross Line and 2 Dot Laser Level

Product Specifications

• Mounting Positions: Upright, tripod with 1/4-20 screw, ferrous surface with magnets, nail with mounting hole
• Battery Type: Li-ion
• Charging Port: Type C USB
• Charging Time: Approximately 5 hours

Product Usage Instructions

• Place the unit in an upright position on a stable, flat surface or mount it to a tripod using a 1/4-20 threaded screw.
• Alternatively, you can attach it to a ferrous surface using the magnets provided or hang it on a nail using the mounting hole.
• The non-mar rubber feet prevent damage to surfaces.

Charging the Li-ion Battery

1. Ensure the locking compensator is in the locked (OFF) position.
2. Rotate the laser to access the rear of the unit.
3. Press down on the battery door lock tab to unlock and open the battery door. Remove the lithium battery case.
4. Check the battery fuel status by pressing the micro switch on the battery.
5. Connect a Type C USB charger to the battery charging port located on the front of the battery and plug it into a power source.
6. The battery is fully charged when all three LEDs are lit. Charging time is typically five hours.

FAQ

• Q: How do I know when the battery is fully charged?
• A: The battery is fully charged when all three LEDs are lit on the fuel gauge.
• Q: Can I mount the unit on a non-ferrous surface?
• A: It is recommended to use the provided mounting options for best results. Mounting on a non-ferrous surface may affect stability.

Thank you for purchasing this GreenBrite® Cross-Line & 2 Dot Laser! We want to get you up and running as quickly as possible – but this quick start guide is not a replacement for reading and understanding your operator’s manual. For complete safety and operating instructions, refer to the operator’s manual.

CHARGING LI-ION BATTERY

1. Ensure the locking compensator is in the locked (OFF) position.
2. Rotate the laser so the rear of the unit is accessible.
3. Push down on the battery door lock tab to unlock and open the battery door. Remove the lithium battery case from the unit.
4. Press the micro switch on the battery to check its fuel status. See Figure 1.
5. Connect a Type C, USB charger to the battery charging port located on the front of the battery and plug the charger into a power source.
6. When all three LEDs are lit, the battery is fully charged. Charge time is typically five hours. See the table below.
   Fuel Gauge| LED1| LED2| LED3
   ---|---|---|---
   Volt of battery <3.5V| ON| OFF| OFF
   3.5V ≤ Volt of battery <3.8V| ON| ON| OFF
   3.8V ≤ Volt of battery| ON| ON| ON
7. Reinsert the lithium battery into the unit. Be sure the end with the openings is inserted first.

MOUNTING POSITIONS

• Place the unit in an upright position, either on a stable, flat surface, mount it to a tripod with a 1/4″‑20 threaded screw, mount it to a ferrous surface using the magnets, or hang it on a nail using the mounting hole.
• Non-mar rubber feet on the unit prevent damage to surfaces.

OPERATION / AUTOMATIC MODE

1. Slide the locking compensator/power switch to the left to the unlocked (ON) position to power the unit. NOTE: The unit must be within ±4° of the level for the self-leveling feature to function properly. If the unit is beyond its 4° self-leveling range, the laser will not self‑level, the laser will flash, and the level indicator status light will flash red.
2. On the keypad, press the button to turn on the horizontal laser beam. Press the button to turn on the vertical laser beam. Press the button to turn on the dot laser beam. The unit can be used with any combination of laser beams turned on simultaneously.
3. When using the vertical (plumb) laser beam, rotate the unit to the desired position. Use the fine‑tuning adjustment knob to make small adjustments.
4. Slide the locking compensator to the right to the locked (OFF) position to power off the unit.

OPERATION / TILT (MANUAL) MODE
The pendulum lock secures the laser during transport to prevent damage to the self-leveling mechanism. It also enables the laser to be used at any angle in manual mode.

1. The unit can be used to project laser beams at any angle desired, such as when projecting a line for stairs or a railing. This mode produces the best results when the unit is mounted on a tripod. With the locking compensator in the locked (OFF) position, press and hold any of the buttons on the keypad for three seconds to power the unit. The status lights will illuminate. The level indicator LED will light a steady red to indicate the unit is not self‑leveling.

2. On the keypad, press the button to turn on the horizontal laser beam. Press the button to turn on the vertical laser beam. Press the button to turn on the dot laser beam. The unit can be used with any combination of laser beams turned on simultaneously. Adjust the unit to the desired angle. The lasers will not self-level.
   NOTE: While in manual level mode, active lasers will flash three times, at one-second intervals, every 15 seconds. This is a visual indication that the unit is in manual-level mode and will not self‑level.

3. Press any of the laser beam buttons for three seconds to power off the unit.

CONTACT

• Download the full manual
• www.johnsonlevel.com/manuals
• JLD300-GN2D
• ©2024 Johnson Level & Tool

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>