JOHNSON 1888-0700 7 Inch Digital Angle Locator and Ruler User Manual
- October 27, 2023
- Johnson
Table of Contents
- JOHNSON 1888-0700 7 Inch Digital Angle Locator and
- Key Features
- LOCATION OF PARTS/COMPONENTS
- INSERTING BATTERIES
- USING THE PRODUCT
- COMMON APPLICATIONS
- TROUBLESHOOTING
- CARE AND HANDLING
- SPECIFICATIONS
- PRODUCT REGISTRATION
- PRODUCT WARRANTY
- CONTACT US
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
JOHNSON 1888-0700 7 Inch Digital Angle Locator and
Ruler
Thank you for purchasing this Johnson digital angle locator and ruler. We suggest you read this instruction manual thoroughly before using the tool and save this instruction manual for future use.
Key Features
- The dual display indicates degrees/degrees minutes
- Stainless steel ruled blade in 1/32nds and mm
- Simple three-button operation
- Blades lock at any angle
LOCATION OF PARTS/COMPONENTS
ON/OFF/ZERO button: Short press when the unit is off, turns unit on. Short
press when the unit is on, displays “0.00”. Press and hold for 3 seconds to
turn the unit off.
HOLD button: Single press displays “H” in the lower right corner and
holds the last displayed value regardless of arm position. Pressing while held
value is displayed turns off “H” in the lower right corner and releases the
value. The display reads value relative to calibration.
D/M button: Toggles displayed engineering units from “0.00°” (degrees) to
“0°00’” (degrees. minutes).
Locking Knob: When rotated clockwise, locks the arm in the current
position. When rotated counterclockwise, unlocks the arm making it free to
rotate and measure other angles.
INSERTING BATTERIES
- Open the battery compartment by pressing a button.
- Remove the battery holder by pulling it out from the opposite side.
- Install 3V CR2032 lithium battery in holder, negative side up.
- Re-install the battery holder, making sure it is fully closed.
Note: 5 minutes of inactivity automatically turns unit off.
USING THE PRODUCT
Power the unit on by pressing the ON/OFF/ZERO button. The display should read “0.00” regardless of the position of the ruler/angle arms. Movement of the arms automatically indicates a measured angle with reference to the arm placement when the unit was turned on. To calibrate the display to a 0° reference angle, place the arms on a flat surface and press the ON/OFF/ZERO button as shown below. The display is now calibrated to a reference angle of 0°.
COMMON APPLICATIONS
- Easy-to-read LCD displays in degrees/degrees minutes
- Ideal for checking and transferring angles for remodeling, cabinet installation, roof angles, format for concrete pours, and much more
- Zero function to set any angle as a zero point
TROUBLESHOOTING
- The tool does not power on or remain on Replace batteries. Check battery polarity.
- LCD is not reading correctly Perform calibration of the tool. See “USING THE PRODUCT”.
CARE AND HANDLING
- Remove any moisture or dirt with a soft, dry cloth.
- Remove the battery when storing the tool for an extended time (more than 3 months).
SPECIFICATIONS
Working Angle Range: | 0° to 360° |
---|---|
Accuracy Angle/ Resolution: | 0.05° (degrees) or 0.03′ (minutes) |
Battery: | 1 x 3V CR2032 |
Operating Temperature: | 32°F to 122°F |
Weight/Dims | .36 lbs, 8.563″ x 1.375″ x 0.813″ |
PRODUCT REGISTRATION
Please register your product within 30 days of purchase. Registering ensures we have your information on file for warranty service even if you lose your receipt and lets us contact you if there is ever a product recall. We will never sell your information and will only send you marketing information if you opt in.
PRODUCT WARRANTY
Johnson Level & Tool offers a one-year limited warranty on this product. You
can obtain a copy of this warranty on our website or by contacting our
customer service department. The limited warranty contains various limitations
and exclusions.
Note:
The user is responsible for verifying proper calibration before each use. If
you experience problems with this product, please contact us.
CONTACT US
Email: service@johnsonlevel.com
Tel: 888-953-8357
Online: www.johnsonlevel.com
To register, scan or click: www.
johnsonlevel.com/register
References
- Levels | Laser Levels | Rotary Laser Levels | Construction Measuring Tools | Spirit Level | Builder Levels | Johnson Level & Tool Mfg Company
- Johnson Level Manuals | Johnson Level & Tool Mfg Company
- Laser Level Registration | Level Registration | Construction Measuring Tool Registration | Johnson Level & Tool Mfg Company
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>