GLAKER HC-2022 Hair Trimmer Cordless 3 in 1 Versatile Hair Clippers User Manual
- June 15, 2024
- GLAKER
Table of Contents
Household Hair Clipper
HC-2022
User Manual
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be
observed, including the following.
Read all the instructions before using this appliance.
DANGER
To reduce the risk of electric shock:
Do not reach for an appliance that has fallen into water.
Unplug it immediately.
Do not use it while bathing or in the shower.
Do not place or store this appliance where it can fall or be pulled into a tub
or sink.
Except when charging, always unplug this appliance from the electrical outlet
immediately after using.
Unplug this appliance before cleaning it.
WARNING
To reduce the risk of burns, fire, electric shock or injury to persons:
This appliance is for household use only.
An appliance should never be left unattended when it’s plugged in, except when
it is rechargeable appliance and is being charged.
Close supervision is necessary when this appliance is used by, on, or near
children or persons with reduced abilities.
Use this appliance only for its intended use as described in this manual.
Do not use attachments not recommended by the manufacturer.
Keep the cord away from heated surfaces.
Never operate this appliance if it has a damaged cord or plug, if it is not
working properly, if it has been dropped or damaged, or if it has been dropped
into water. If any of these things happen, return the appliance to an
authorized service center for examination and repair.
Never drop or insert any object into any of the appliance’s openings.
Do not use it outdoors or operate where aerosol (spray) products are being
used, or where oxygen is being administered.
Make sure the cord is disconnected from the clipper while storing them and
make sure they are stored in a moisture-free area. Do not store them in
temperatures exceeding 140°F (60°C).
Do not use this appliance with a damaged or broken cutter unit, as injuries
may occur. Always make sure the blades are aligned properly.
Always first connect the power cord to the appliance, then plug the appliance
into an outlet. Before storage, turn it off and then pull out the adapter from
the outlet, then disconnect the power cord from the clipper.
Do not use an extension cord or a voltage converter with this appliance.
Do not wrap the cord around the appliance.
Dispose of used batteries properly. Do not incinerate. Batteries may explode
if overheated. Do not wrap them in metal or aluminum foil. Wrap them in
newspaper before discarding them. It is recommended that you contact local
battery redemption site(s) in your area
SAVE THESE INSTRUCTIONS
Components
Household
Hair Clipper| Motor| Operating Voltage : 3V DC
---|---|---
High Performance Motor
Battery| 2000mAh Li-ion Battery
Operating Voltage : 3V DC
Operating Voltage : 3V DC
USB Charge Cable| USB Type-C cable
Adjustable Blade Head| Ceramic + Stainless Blade, Hair Lengths 0.5-2.5mm
T-shaped Blade Head| Stainless Blades in T-Shaped
Detail Blade Head| 7mm Wide Stainless Blades
Power Off/On/Turbo Switch
Battery LED indicators
When the unit is being charged, four LED indicators including one red light and three white lights flash in different numbers to indicate the following:
- Four lights blink successively: The unit is in a 0-10% charged state.
- Red light (off) & three white lights blink in succession: The unit is in a 11-25% charged state.
- Red light (off) & white lights (one remains on and two are flashing): The unit is in a 26-55% charged state.
- Red light (off) & white lights (two remains on while the other one is flashing)
- Red light (off) and white lights remain on: The unit is in a 85-100% charged state.
Charging your Clipper
OPERATION
Turn on the unit by pressing the ON/OFF switch. After use, switch it off.
After being fully charged for 4 hours, the appliance will have 5 hours
runtime.
This unit is shipped in a partially charged state. Charge the unit for two
hours after purchase and BEFORE first use.
How to Recharge
Insert the type-C USB power cord into the rear port of this hair clipper, then
connect the cable to a power supply for charging.
Attachment Combs
Guide combs help users cut hair with desired lengths by keeping the blades at
a set distance from the skin.
There are 13 guide combs offering users a variety of hair length options
(3/6/9/13/16/19/22/25/32/38/51mm/ Left/Right).
For easy reference, every guard comb is numbered and the numbers of hair
lengths the hair are listed on the guide combs. Always start with a relatively
large size guide comb (you can always replace it with a small size guide comb
if the hair length is not short enough).
If this is the first time you use a hair clipper to cut hair by yourself, try
to cut hair in a small area on your head until you are clear about the length
of hair each guide comb provides.
To achieve an even “tapered” cut around the ears, use the LEFT and RIGHT
tapered guide comb.
Before mounting or removing guide combs from hair clippers, make sure they
have been turned off.
Mounting Guide Combs
- Align the guide comb with the blades’ edges.
- Slightly push the guide comb down until it snaps into place
Removing Guide Combs
Grab the rear of the guide comb firmly and pull it off the hair clipper (Don’t
try to do this with teeth of the guide comb)
Adjustable Clipper Blade
This hair clipper is equipped with an adjustable dial knob on the blade head that can adjust the closeness of hair trimming. When the dial knob is at the position 0.5mm, the blade will provide the closest trimming. Rotating the Dial Knob counterclockwise can gradually increase the length of the blades, which means hair left on heads will be longer.
Detachable Blade Head
Detaching Blade Head
Before removing the blade head, make sure the unit is turned off. Push the
groove to slide out the blade head.
Assembling Blade Head
Before assembling the blade head, make sure the unit is turned off.
Insert the blade head into the slots on the hair clipper until there is a
“click” sound.
Clipper Care
BLADE Maintenance AND LUBRICATING
In order to ensure that this hair clipper runs to its longest life span, daily
lubrication is recommended.
To lubricating it properly, apply one drop of glaker lubrication oil on the
teeth of the movable upper blade and one drop on each end of the upper blade.
Turn on the hair clipper and let it run for 1 minute. When the oil is evenly
distributed, turn off the hair clipper and wipe off excess oil with a soft
cloth. Periodically lubricate the teeth of the blade to reduce blade friction.
To ensure long lasting performance of your clipper, clean the blades and the
surface of the unit regularly.
After each use
Make sure the appliance is switched off and unplugged from the power outlet
before cleaning.
Brush the accumulated hair residue from the blades and the body of the
clipper. The blades can be rinsed under water if it is detached from the body
of the unit. To clean the unit, wipe with a damp cloth and wipe it with a dry
cloth immediately.
Do not rinse o submerge the clipper in water.
Apply a few drops of sewing machine oil onto the blades. Wipe off excess oil.
Cleaning
- Switch off the product and disconnect it from the wall outlet.
- Wipe the handle of the product with a dry cloth.
- Remove any guide comb or attachment from the product.
- Blow off any hair residue that has accumulated in the blade part of the hair clipper.
- Blow off any hair residue that has accumulated on the attachments and/or guards.
- Clean the clipper with a soft brush, like the one that comes with the product.
Caution
Clean the clipper with a soft brush, like the one that comes with the product.
Do not rinse or submerge the clipper in water.
Do not use harsh or corrosive cleaners on the unit or its blades.
Ensure the appliance is switched off and unplugged from the outlet before
cleaning.
Storage
Unplug the hair clipper and store the unit in a safe dry place and keep it out
of reach of children. Never wrap the cord around the hair clipper as this will
cause the cord to wear in a quicker way. Handle the cord carefully so that it
can have a long life span and avoid jerking, twisting or straining especially
the plug connections.
Product Disposal
When this rechargeable hair clipper reaches the end of its usable life, the
batteries must be removed, recycled or disposed of properly in accordance with
local laws or requirements of communities.
The following procedure should be followed for battery removal: The
rechargeable battery must be removed from the appliance before it is scrapped.
Disconnect the charging cable before removing the battery.
Ensure that the battery is fully discharged. To do this, operate the trimmer
until it stops.
Remove the comb attachment Remove the blade cartridge Pry the decorative panel
off the top housing to expose the internal parts and printed circuit board.
Unscrew the screws on the big printed circuit board and screws on the small
printed circuit board.
Disconnect the battery from the circuit board.
The battery must be disposed of at an appropriate official
recycling/collection center.
Do not attempt to operate the trimmer once you have detach it.
Warranty
1-YEAR WARRANTY
If your Glaker product fails to operate as expected within one year from the
date of original purchase or from the date on the receipt, Glaker will, at our
option, repair it for you or replace it with a new one FREE OF CHARGE.
Question? Contact us at: support@glaker.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>