moonki 900W PMPO Power Portable Speaker Instruction Manual
- July 2, 2024
- moonki
Table of Contents
@moonki.sound
www.moonki.com
PORTABLE SPEAKER
WOOFER 6.5” x2 • TWEETER 1.5” x2
900w
PAIPO POWER
Instruction Manual
Specifications
Speaker Type: Active | Wireless connection |
---|---|
PMPO Power 900W | TWS function |
RMS Power 60W | Mic connections 6.35mm x 2 Aux connection 3.5mm |
Class D Amplifier Board | USB charging output |
Woofer 6.5″ x 2 | Lithium Battery 7.4 V/6000 mAH |
Tweeter 1.5″ x 2 | 5V 2A charging input |
25.5 mm KSV Voice Coil | Unit Measurements 23.6 x9.25x 9.85in |
Sensitivity 88dB | Unit Weight 14.1 Lbs |
Signal-to-Noise Ratio 65 dB | Box measures 271x 11.3 x 11.6 in |
Frequency response 65Hz – 19KHz | Box Weight 17.2 Lbs |
INCLUYE 1 Wireless Microphone, Strap, USB Type-C Charging Cable, User Manual and Warranty Card.
Functional Brief Description
Mic1| Microphone Input 1
Mic2| Microphone Input 2
AUX| External Audio Input
usB| USB Socket
ON/OFF| Power Switch
DC 5V| Type-C USB Charge
-MIC VOL+| Microphone Volume Control up/Down
-ECHO+| ECHO Control Up/Down
-BASS+| BASS Control Up/Down
-TREBLE+| TREBLE Control Up/Down
-VOLUME+| VOLUME Control Up/Down
| Light Mode
MIC PRI| Microphone Priority
TWS DIMMER| TWS function/ light luminance level adjustment
| Repeat/Bluetooth Device Disconnect/ Frequency Switch
| Last Song
| Play and pause
| Next Song
MODE| Mode Switch
MODE SWITCH
Short press “MODE” button to switch mode “BT —) AUX IN” mode
The first time booting will enter into Bluetooth model by default, the next
booting will enter into the same mode and setting as last selection.
BLUETOOTH CONNECTING
Short press ” MODE ” button switch to BT mode, choose model TRIP on your Bluetooth device to connect -Bluetooth Player: Under Bluetooth mode, short press “ ” for next song; short press “ ” for last song; Press ” ” for pause, press once again to replay.
-
Force Disconnect Bluetooth Device: In Bluetooth mode, press “ ” to force disconnect the current
Bluetooth device, another Bluetooth device can search the speaker name No.B361 to connect -
Warning Tone turn on/ off: Long press “MODE” button to turn on or turn off the prompt voice, display screen show
AUX MODE
- Insertthe AUX cable, and then press the ”MODE ” button switch to AUX mode.
- In Aux mode, press“ ” button to MUTE , display show , press ” again to exit MUTE.
MICROPHONE INPUT
In random mode, when using the wired/wireless microphone, Mic volume and echo volume can be adjusted MIC PRI: microphone priority. When using the microphone, short press MIC PRI button to automatically turn down the music volume.
TWS FUNCTION
Switch both speakers to Bluetooth mode, press and hold ” ” on one speaker(as right channel) for more than 2 seconds to enter TWS mode. While pairing, the TWS indicator will be flashing. After TWS connected successfully, there will be a warning tone and the indicator light of both speakers with be on. The speaker which connected to your Bluetooth device acts as the primary speaker (left channel). Press and hold ” ” more than 2 seconds to exit TWS mode.
LIGHT CONTROL
- In random mode, short press the“ ” to turn on the light, long press these ” ” to turn off the light.
- Short press“ ” to switch 4 light effects.
- When the light is on, short press “ ” button enter light luminance level adjustment. Short press ‘ ” and “ ” to adjust the luminance level from d 1-d 10.
- After the adjustment is completed, short press ” ” again to exit the light adjustment and return to the current interface, or automatically exit the light adjustment interface after 3 seconds without any operation.
RECHARGE
When ” ” flashing slowly, it indicates that the battery is under charge and
needs to be immediately charged and the playback volume should be reduced or
turned off;
If continue to play, it will automatically shut down when the battery is below
the protection voltage(Automatic shutdown below 6.0V) and display ‘‘ ”. Then
display ‘‘ ”, the machine enters standby mode
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receivingantenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Mobile
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>