HANECO SKYLUX120W-G5 Highbay and Lowbay Lighting Installation Guide
- June 30, 2024
- HANECO
Table of Contents
HANECO SKYLUX120W-G5 Highbay and Lowbay Lighting
Product Specifications
- Product Code: SKYLUX120W-G5, SKYLUX200W-G5
- Power: 70/100/120W, 150/170/200W
- CCT: 4000/5000/5700K
- Voltage/Frequency: 220-240Vac 50/60Hz
- IK/IP Rating: IK08 IP65
- Operating Temperature: Not specified
Installation
- Ensure the main power supply is switched off before commencing the installation.
- Remove the IP65 cover to access the power and color dip switch. Push inward and turn counterclockwise to remove the IP65 cover.
- Set the desired power and color tone.
- SKYLUX G5 model has the color switchable option.
- Fittings are preset with the highest wattage. To adjust to a lower fitting wattage, turn the dip switch to ADJ.
- Ensure to install the IP65 cover.
- Screw the eye bolt on top of the luminaire.
- Install optional accessories and desired mounting settings.
- Install the luminaire in the desired location.
Mounting Options
- Ceiling mounting with hook
- Ceiling or wall mount with bracket (Not Included, available as accessories)
- Mounting bracket holes
Motion Sensor Installation
- Switch Off the power supply. Remove the IP65 cover by rotating it counterclockwise and pull outward.
- It is the correct installation when the microwave sensor is aligned with the marker as shown in the image. Turn ON the unit power and set the microwave sensor suit.
Product Dimensions
- Product a 120W: 280
- Product a 200W: 320
Accessories (Not included)
| Product Code | Part Number | Description |
|---|---|---|
| SKYLUXG4-BRKT | 2002276 | For more information www.haneco.com.au 1300 001 LED |
Last
updated 23/04/24
Thank you for choosing Haneco SKYLUX G5 Highbay.
We strongly recommend that you read this manual carefully before installation.
This installation guide is suitable for the SKYLUX G5 model.
WARNING
• Installation must be carried out by a licensed electrician and by these
instructions and relevant Australian standards and local regulations.
• Ensure input voltage conforms within product specifications.
• Ensure wires are securely connected.
• Before switching on, ensure all wires are correctly connected.
• The warranty is void if the product is not installed according to the
instructions.
• The external flexible cable or cord of this luminaire cannot be replaced; if
the cord is damaged, the luminaire shall be destroyed
Note
Product technical information and specification may change over time without
prior notice. For the latest information, please contact our customer service
or visit our website www.haneco.com.au
Product Specification
Installation
1. Ensure the main power supply is switched off before commencing the
installation.
2. Remove the IP65 cover to access the power and color dip switch. Push
inward and turn counterclockwise to remove the IP65 cover as shown in the
figure below.
3. Set the desired power and color tone.
Note
- Skylux G5 model has the color switchable option.
- Fitting is preset with its highest wattage. To adjust lower fitting wattage, turn the dip switch to ADJ.
4. Ensure to install the IP65 cover.
5. Screw the eye bolt on top of the luminaire.
6. Install optional accessories and desired mounting settings.
7. Install the luminaire in the desired location.
Mounting Option
Motion Sensor Installation
STEP 1. Switch Off the power supply. Remove the IP65 cover by rotating it counterclockwise and pull outward.
STEP 2. Insert the microwave sensor (HIGHBAY- MS: 20022281). Push downward and turn clockwise (360°) to engage the sensor. Motion sensor settings are set using a remote controller (HIGHBAY-REMOTE: 2002282).
STEP 3. It is the correct installation when the microwave sensor is aligned with the marker as shown in the image. Turn ON the unit power and set the microwave sensor suit.
Product Dimension
Accessories (Not included)
For more information www.haneco.com.au 1300 001 LED
FAQ
Q: Can I adjust the power and color tone of the luminaire?
A: Yes, you can set the desired power and color tone by accessing the
power and color dip switch