HOFTRONIC GU10 Blenda Pir Sensor Led Wall Light User Manual

HOFTRONIC GU10 Blenda Pir Sensor Led Wall Light

IMPORTANT SAFETY DETAILS

1. Ensure the AC/Mains power is NOT connected and cannot be unexpectedly reconnected during installation.
2. This product must be installed by a qualified electrician in accordance with instructions provided and in compliance with recognised electrical and safety regulations relevant to the country it is being installed.
3. This product may NOT be installed by minors or people with a mental disability.
4. This wall light must be installed to the current edition of the IEE wiring regulations and relevant building regulations in your country.
5. This wall light is designed for indoor and outdoor use.

CHANGING THE TIMER

Decreasing the timer will keep the lamp burning for a shorter time, increasing the timer will keep the lamp burning for a longer time after the lamp will turn on.

CHANGING THE SENSOR SENSITIVITY

Decrease the twilight sensor sensitivity if you want the lamp to turn on only when it is dark, by increasing the twilight sensor sensitivity the lamp will turn on earlier, for example when it starts to get dark or when it is very cloudy.

DECREASING THE TWILIGHT SENSOR SENSITIVITY

INCREASING THE TWILIGHT SENSOR SENSITIVITY

CHANGING THE DETECTION RANGE

Decrease the detection range if you want the lamp to turn on when you are closer, increase the detection range if you want the lamp to turn on already when you are further away.

HOW TO CHANGE INTO MANUAL MODE

1. When power on, the PIR detector enters into the “warm up” for about 1 minute, then it will automatically change into auto mode.
2. During auto mode, by switching on/off 2 times within 3 seconds and then switch on again, the PIR detector will automatically change into manual mode. In manual mode, the lamps will remain on, the PIR detector will not be affected by duration time and lux control level.
3.  During manual mode or auto mode, by switching off over 6 seconds an then on again, the PIR detector will reset to “warm up” maybe shorter than 1 minute.

INTENDED USE / APPLICATION

Product designed for the use in households and for other similar general applications.

MOUNTING

Technical changes reserved. Read the manual before mounting. Mounting should be performed by an appropriately qualified person. Any activities to be done with disconnected power supply. Exercise particular caution. Product has a protective contact/terminal. Failure to connect the protective lead may lead to electric shock. Mounting diagram: see pictures. Check for proper mechanical fastening and connection to electrical power prior to first use. The product can be connected to a supply network which meets energy quality standards as prescribed by law. To maintain the proper IP protection level, the right diameter of the power cable should be selected for the cable gland used in the product.

FUNCTIONAL CHARACTERISTICS
Product can be used indoors and outdoors.

USAGE GUIDELINES / MAINTENANCE
Any maintenance work must be performed when the power supply is cut off and the product has cooled down. Clean only with soft and dry cloths. Do not use chemical detergents. Do not cover the product. Ensure free air access. Product may heat up to a higher temperature. Product can only be supplied by rated voltage or voltage within the range provided. It’s forbidden to use the product with damaged protective cover. Product must not be used in unfavourable conditions, e.g. dust, water, moisture, vibrations, explosive air atmosphere, fumes, or chemical fumes, etc. Nondemountable product. Not suitable for independent repairs.

ENVIRONMENTAL PROTECTION

Keep your environment clean. Segregation of post-packaging waste is recommended. This labelling indicates the requirement to selectively collect waste electronic and electrical equipment. Products labelled in this way must not be disposed of in the same way as other waste under the threat of a fine. These products may be harmful to the natural environment and health, and require a special form of recycling/ neutralising. Products labelled in this way should be returned to a collection facility for waste electrical and electronic goods. Information on collection centres is provided by local authorities or sellers of such goods. Used items can also be returned to the seller when new product is purchased, in quantity no larger than the purchased item of the same type. The above rules regard the EU area. In the case of other countries, regulations in force in a given country must be applied. Contacting the distributor of our products in a given area is recommended.

COMMENTS / GUIDELINES
Failure to follow these instructions may result in e.g. fire, burns, electrical shock, physical injury and other material and non-material damage. For more information about Hoftronic products visit www.hoftronic.com. Hoftronic shall not be responsible for any damage resulting from the failure to follow these instructions. Hoftronic reserves the right to make changes in the manual – the current version can be downloaded at www.hoftronic.com.

DECLARATION OF CONFORMITY

DOCUMENTATION
This product has been manufactured and supplied in compliance with all relevant regulations and directives applicable to all member states of the European Union. The product complies with all applicable regulations and rules in the country of sale. Formal documentation such as the declaration of conformity, the safety data sheet and the product test report is available upon request.

CE DECLARATION
The product complies with the following directives:

• LVD: 2014/35/EU
• EMC: 2014/30/EU
• RoHS: 2011/65/EU

The complete Declaration of Conformity Document (DOC) is available upon request.

Imported by
HOF Trading B.V.
Fahrenheitstraat 11, 6003 DC Weert , The Netherlands
Made in P.R.C.
www.hoftronic.com

References

• HOFTRONIC - HOFTRONIC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>