KOMODO PORTBIDEA Portable Bidet User Guide

KOMODO PORTBIDEA Portable Bidet

Product Information

Specifications

• Voltage: 3.7V DC
• Current: 0.8A
• Water flow: 500ml/min
• Power supply: Lithium battery
• Product size: 47x103mm
• Capacity of Battery: 450mAh
• Using time: 30 minutes
• Charging way: Any USB output of 5V, 0.5-1A
• Charging time: 2 hours
• Configure bottle: 200ml

Product Usage Instructions

Using the Bidet with the Provided Bottle

1. Unpack the package and take out the product. Rotate anticlockwise to remove the lower cover of the bottle. Remove the bidet body, then put the lower cover back and rotate clockwise to lock it in place.
2. Fill the bottle with clean water. Attach the bidet body to the bottle by turning it clockwise and unfolding the spout.
3. Place the bottle upside down.
4. Press the Power button to commence the low-pressure setting. Press again for the higher pressure setting. Press again to turn it off.
5. After cleaning, store the bidet body inside the bottle and close the silicone lid.

Using the Bidet with an Alternative Bottle

1. Attach the bidet body to the bottle by turning it clockwise.
2. Place the bottle upside down, unfold the spout, and position it correctly for cleaning.
3. Press the Power button to commence the low-pressure setting. Press again for the higher pressure setting. Press again to turn it off.
4. After each use, fold the spout into the slot and release the bottle from the bidet body by turning the bidet body anti-clockwise.

Charging

1. Remove the charging port cover and plug one end of the provided USB cable into the charging port.
2. Plug the other end of the USB cable into one of the following (not provided):
   • a) 5V USB power adapter.
   • b) USB output from a car.
   • c) USB output from a laptop.

WARNING:
Do not use a power adapter with an output higher than 5V to charge the product, it may damage the battery and cause fire or explosion.

FAQ

Q: What should I do if there is no water coming out during use?
A: Clean the nozzle and inlet filter to ensure proper water flow.

SAFETY & WARNINGS

• Read all instructions carefully before using the product and retain this user guide for future reference.
• Be familiar with the method to turn off the product immediately.
• Operate only with water within the temperature range 10°C to 50°C. Never use boiling water with this product.
• This product includes small parts that could be a choking hazard.
• Do not leave the product unattended when in use. Switch the product off and remove it from the water when not in use.
• Do not use replacement parts or attachments unless recommended by Kogan.com.
• Do not use this product with water from the sea, pool or river or with any liquid other than clean water.
• Do not block the nozzle during use.
• Ensure the charging port cover is closed tight during use.
• Do not submerge the product in water to avoid damage.
• When the product is operated by children, proper instruction and supervision should be provided.
• Recharge the battery using a DC 5V 0.5A~1A power adaptor.
• Do not use a damaged power cord or plug and charge only with the correct voltage as listed on the rating plate. Using an improper voltage may result in damage to the product and possible injury.
• Before use, ensure that that there are no broken or worn parts and that all screws are fully tightened.
• Keep the product away from heat and fire.
• Avoid freezing the product. Freezing will damage the motor and the cord.
• Do not disassemble the product.
• Do not overcharge the product or charge it overnight.

OVERVIEW

OPERATION

Using the Bidet with the Provided Bottle

1. Unpack the package and take out the product. Rotate anticlockwise to remove the lower cover of the bottle. Remove the bidet body, then put the lower cover back and rotate clockwise to lock it in place.
   Note:
   The bottom cover will be easier to remove after opening the silicone lid first.

2. Fill the bottle with clean water. Attach the bidet body to the bottle by turning it clockwise and unfolding the spout.
   Note:
   This product can also be used with bottles that conform to the thread of the bidet body.

3. Place the bottle upside down.

4. Press the Power button to commence the low-pressure setting. Press again for the higher pressure setting. Press again to turn it off.
   Notes:

   • If there is no water coming out during use, clean the nozzle and inlet filter.
   • Do not block the nozzle when spraying, as it will cause excessive internal pressure leading to internal damage and water seepage.

5. After cleaning, store the bidet body inside the bottle and close the silicone lid.

Note:
When storing the bidet body, ensure the bottle is dry. Otherwise, water vapour may enter the bidet body and cause a short circuit of the PCBA inside the bidet body.

Using the Bidet with an Alternative Bottle

1. Fill an empty water bottle with the required opening size with clean water.
2. Attach the bidet body to the bottle by turning it clockwise.
3. Place the bottle upside down, unfold the spout, and position it correctly for cleaning.
4. Press the Power button to commence the low-pressure setting. Press again for the higher pressure setting. Press again to turn it off.
5. After each use, fold the spout into the slot and release the bottle from the bidet body by turning the bidet body anti-clockwise.

Note:
If there is no water coming out during use, clean the nozzle and inlet filter.

Charging

1. Remove the charging port cover and plug one end of the provided USB cable into the charging port.
2. Plug the other end of the USB cable into one of the following (not provided):
   • 5V USB power adapter.
   • USB output from a car.
   • USB output from a laptop.

WARNING:
Do not use a power adapter with an output higher than 5V to charge the product, it may damage the battery and cause fire or explosion.

Charging Indicator

Charging Notes

• It is recommended to charge the battery to 40%-50% after each use to ensure maximum battery life. Charge before using for the first time.
• Recharge the battery at least every three months to ensure it remains at 40%-50%. The battery will deplete when stored for long periods.
• Do not charge the battery with a power source that exceeds the product’s specified output requirements (Output: DC 5V/0.5-1A).
• Store away from high temperatures and flammable or explosive goods.
• Wipe the bidet dry with a cloth after use and before storage.

SPECIFICATIONS

• Voltage 3.7V DC
• Current 0.8A
• Water flow 500ml/min
• Power supply Lithium battery
• Product size ∅47X103mm
• Capacity of Battery 450mAh
• Using time 30 minutes
• Charging way Any USB output of 5V, 0.5-1A
• Charging time 2H
• Configure bottle 200ML

Need more information

• We hope that this user guide has given you the assistance needed for a simple set-up.
• For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com.

References

• Kogan Help Centre

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>