ARDESTO IHS-1650, IHS-2200, IHS-2800 Infrared Heater Instruction Manual

: June 3, 2024
: ARDESTO

Table of Contents

ARDESTO IHS-1650, IHS-2200, IHS-2800 Infrared Heater
WARNING
EQUIPMENT
SPECIFICATIONS
DEVICE DESCRIPTION
DEVICE ASSEMBLY
CONTROL PANEL
OPERATING THE DEVICE
MAINTENANCE AND CLEANING
TROUBLESHOOTING
СORRECT DISPOSAL OF THE APPLIANCE
Warranty conditions
- WARRANTY CARD
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ARDESTO IHS-1650, IHS-2200, IHS-2800 Infrared Heater

WARNING

The infrared heater is designed for safe operation. Nevertheless, installation, maintenance, and operation of the heater can be dangerous for a careless operator. For your safety and the safety of others, please read the instructions in this USER MANUAL and follow these safety practices in order to prevent damage or injury.

Check that the mains voltage corresponds to the rating of the appliance before operating.
Do not touch hot surfaces.
For indoor use only. For dry location only.
Do not use near or in the immediate vicinity of a bath or swimming pool or any source of liquid
Unplug from the socket-outlet when not in use.
To protect against electric shock, do not immerse the cord or plug in water or any other liquid. Do not handle the plug or power cord with wet hands.
The use of accessory attachments not recommended by the appliance manufacturer, may cause injury.
Allow adequate safe spacing around the heater for cooling and ventilation to avoid any hazards.
Never place flammable objects or clothing on top or near the heater. Do not operate this appliance in the vicinity or near any flammable liquids or flammable material to avoid a fire hazard such as curtains, furniture, shelves, etc. There must be at least 1m distance between the appliance and curtains, wood, cardboard, cloth, etc. materials, living beings, and other appliances.
Check if the main power line provides 220-240V AC, 50/60Hz and if the power line is connected to a fuse. The fuse rating shall be 16 Amperes. This device should be used with a grounded socket and the grounded socket should be away from the heating area and the hot surface. Also, it must be checked that the socket is not damaged.
Do not allow the cord to overhang the countertop where it can be easily pulled by children.
Do not use this appliance for anything else other than its intended use.
Do not put fingers or foreign objects into the grate while in operation.
Do not leave the appliance unattended when in use.
To remove the plug from the outlet, do not pull on the supply cord. Grasp the plug firmly and pull to remove it.
No liability can be accepted for any damage caused by non-compliance with these instructions or any other improper use or mishandling.
This appliance is for household use only.
This appliance is not intended for use by persons (including children) with reduces physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance.
If the supply cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
To prevent overheating of this appliance, keep the air inlets and outlets clean and free of anything that may cause blockage. Check all inlets and outlets from time to time to ensure it is clear of any dirt or dust accumulation.
This appliance is not intended to be operated by means of an external timer or a separate remote-control system.
Continuous exposure to high-intensity infrared radiation at close proximity could be harmful to the eyes or skin. Although an infrared heating tube does not emit ultraviolet electromagnetic radiation, harmful burns could still result if an operator is in close contact with the heating tube being operated at high intensity. Because of the brilliant light emitted by the infrared heating tube at full intensity, is recommended that the eyes be shielded from the glare if observing the heating tube or radiant that chamber for an extended period of time. Use suitable shaded lenses or dark glasses.
Parts of the heater may exceed 200°C. Contact with the heating tube, reflector, or mental parts near the heating tube, may cause severe BURNS.
NEVER place hands under the heating elements. ALWAYS allow the heating element to cool at least 10 minutes before touching the heating tube or adjacent parts.
Observe that all applicable local and national electrical codes are met and a safe electrical ground system is installed before attempting to operate the heater. Refer to the proper installation procedures.
This product contains recyclable materials. Do not dispose of this product as unsorted municipal waste. Please contact your local municipality for the nearest collection point.
Obey the same fire safety rules you observe when you work with hot plates, high-intensity infrared heaters, propane or acetylene torches, soldering irons, and other equipment that gets very hot.
Know where the nearest fire extinguisher is located and how to use it.
Know how to put out the fire from all types of material near the infrared heater.
Statement: heater is not located immediately below a socket outlet.
Do not use the appliance while sleeping or while you’re away from where the appliance is located.
Avoid using extension cords, excessive heating may cause a fire. If you have to use an extension cord, make sure that the cable cross-section is at least 2 sq. mm (14AWG).
Your device must stand on a level and smooth surface during use. Do not use it on uneven or unstable surfaces.
Children of less than 3 years should be kept away unless continuously supervised.
Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

CAUTION!
Some parts of this product can become very hot and cause burns! Particular attention has to be given where children and vulnerable people are present!

WARNING:
In order to avoid overheating, do not cover the heater. Never close the ventilation channels.

WARNING!
This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when occupied by persons not capable of leaving a room on their own, unless constant supervision is provided.

Dear Customer,
Thank you for relying on our products. We advise you to read this user manual thoroughly before using the infrared heater and keep it permanently so that the features of the infrared heater you have purchased will stay the same as the first day for a long time and serve in an optimum and efficient way.

NOTE:
This Instruction Manual is prepared for multiple models. Your appliance may not feature some functions specified in the manual. These functions are marked by the sign *.
This appliance is intended for domestic use. It is not intended for commercial use.

EQUIPMENT

Infrared heater – 1 pc.
Instruction manual (with warranty card included) – 1 pc.

SPECIFICATIONS

Model

| Height, mm (А)| ****

Width, mm (B)

| Depth, mm (С)| Rated Power (W)| ****

Supply

| Mode 1 Power, W| Mode 2 Power, W| Mode 3 Power, W| Mode 4 Power*, W
---|---|---|---|---|---|---|---|---|---

IHS-1650

| ****

445

| ****

545

| ****

172

| ****

1650

| 220-240V ~,

50/60 Hz

| ****

550

| ****

1100

| ****

1650

| ****

–

IHS-2200

| ****

535

| ****

545

| ****

172

| ****

2200

| 220-240V ~,

50/60 Hz

| ****

550

| ****

1100

| ****

1650

| ****

2200

IHS-2800

| ****

575

| ****

726

| ****

172

| ****

2500

| 220-240V ~,

50/60 Hz

| ****

625

| ****

1250

| ****

1875

| ****

2500

DEVICE DESCRIPTION

ARDESTO-IHS-1650,-IHS-2200,-IHS-2800-Infrared-Heater-
FIG-1

This product has been produced in accordance with safety rules and directives in force.

NOTE:
The values stated in the markings on the product or in other printed documents provided with the products are the values obtained in the laboratory environment in respect of the relevant standards. These values may change according to the use and ambient conditions of the product.

DEVICE ASSEMBLY

ARDESTO-IHS-1650,-IHS-2200,-IHS-2800-Infrared-Heater-
FIG-2

Open the packaging box and remove the heater from the box, and remove the safety bag and foams from the heater (Figure 1).
Move the legs installed on the product outward and take them out of their tabs (Figure 2,3,4).
Rotate the legs and fix them to the leg inner on the heater with the help of a screwdriver (Figure 5).
Turn the device upside down and place it on its legs. The device is ready for use (Figure 6).

CONTROL PANEL

ARDESTO-IHS-1650,-IHS-2200,-IHS-2800-Infrared-Heater-
FIG-4

OPERATING THE DEVICE

Do not use the product if its parts are absent, broken, or damaged. Contact the Authorized Service.
Do not cover the product with anything. Do not touch the product with damp and wet hands.
ATTENTION: Make sure that no other high-power electrical appliances are connected to the outlet to which the heater is connected.
Plug your device’s plug into a suitable grounded outlet.
Select the required heating mode by pressing the corresponding switch on the control panel.

Due to the inner thermostat, the device may turn on and off periodically during operation. These periodic times may vary depending on the mode in which the device operates and the ambient temperature.

After using the heater, turn the control panel switches to the «off» position and unplug the power cord from the outlet.

Notes:
While the first switching on the heating element burns, therefore the occurrence of a small amount of smoke or foreign smell is possible. It is normal, after some time the smoke and smell will disappear. It is recommended to ventilate the room.

The heater has a tip-over safety system.
In the event of any tip over the safety system will activate and turn off the device’s power. Turn off the device, unplug the power cord from the outlet and make sure that the cause of the tipping over is eliminated. After that return the heater to the working position and turn it on again.

Please note:
If the device is not used for a long period of time, as well as during cleaning or maintenance or moving, the heater must be turned off and unplugged from the electrical outlet.

Periodic inspection and removal of contamination will ensure the safe use of the device.

MAINTENANCE AND CLEANING

Regular and thorough cleaning will help your infrared heater work efficiently for many years without problems. Reflectors (reflecting mirror) and quartz glass tubes must be checked at least once a month against dirt. If dirty, cleaning and maintenance instructions should be applied. Depending on the amount of dust in the usage environment the said checks should be performed more frequently.

When cleaning the device and after long-term storage, it is recommended to check the power cord and plug. If the power cord or plug is damaged do not use the device and contact an authorized service center for the replacement of the damaged parts. It is recommended to replace the reflector every two years for more efficient operation of the appliance. The reflector must be replaced by authorized service. A clean reflector ensures that the heating efficiency of the appliance is maximum.

To clean your heater, follow the steps below:

Unplug the power cord for your safety before cleaning your appliance.
Make sure the heater is cool before continuing
To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. Do not use abrasive detergents to clean the device. After cleaning, dry the unit with a soft cloth. CAUTION: DO NOT let liquids enter the heater.
If the reflector (reflecting mirror) and quartz glass tubes are dirty, they should be cleaned with dry air from outside without opening the protective wire grate of the device.
DO NOT clean your appliance using steam cleaners.
DO NOT use alcohol, gasoline, abrasive powders, furniture polish or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater.
DO NOT immerse the heater in the water
Wait until the heater is completely dry before use.

STORAGE
Store the heater in a cool, dry place when not in use to prevent dust and dirt from getting on its surface. Use the packaging to store the heater.

TROUBLESHOOTING

In case of problems with the operation of the device, please check the recommendations below before contacting the service center.

Trouble	Solution Recommendations

The device does not work

| Check whether the device is correctly connected to the power supply
Make sure the device is in a vertical position
Check that the device’s on/off switches are in the ON position
Check if there are any problems with the electricity supply to the house

СORRECT DISPOSAL OF THE APPLIANCE

This device should not be disposed of as it consists of recyclable parts. Please contact the nearest collection center to recycle this device. Keep the packaging materials out of the reach of children or dispose of them by classifying them in accordance with the waste instructions. Do not dispose of your device and its packaging with normal household waste.

Warranty conditions

The plant guarantees the normal operation of the product within 12 months from the date of the sale, provided that the consumer complies with the rules of operation and care provided by this Manual.
The service life of the product is 5 years.

In order to avoid any misunderstanding we kindly ask you to carefully study the Owner’s Manual, and the terms of warranty, and check the correctness of filling out the Warranty Card. The Warranty Card is valid only if the following information is correctly and clearly stated: model, serial number of the product, date of sale, clear seals of the company-seller, and signature of the buyer. The model and a serial number of the product must correspond to those specified in the Warranty Card. If these terms are violated, and if the information specified in the Warranty Card is changed, erased, or rewritten, the Warranty Card is considered invalid.

Setup and installation (assembly, connection, etc.) of the appliance are described in the attached documentation; they can be carried out both by the user and by specialists having the necessary qualification sent by USC or selling companies (on a paid basis). In this case, the person (the institution) installing the appliance shall be responsible for the correctness and quality of installation (setup). Please pay attention to the importance of the correct installation of the appliance, both for its reliable operation and for obtaining a warranty and free service. Require the installation specialist to enter all the necessary information about the installation in the Warranty Card.

In case of failure of the appliance during the warranty period by the fault of the manufacturer, the owner is entitled to free warranty repair upon presentation of the correctly filled Warranty Card together with the appliance in the factory configuration packed in the original packaging to the warranty workshop or the place of its purchase. Satisfaction of the customer’s claim due to the fault of the manufacturer shall be made in accordance with the law «On Protection of Consumers’ Rights». In the case of warranty repair, the warranty period shall be extended for the period of repair and shipment.

WARRANTY CARD

Dear Buyer!
Congratulations on your purchase of the ARDESTO brand appliance, which was designed and manufactured in accordance with the highest quality standards, and we thank you for choosing this particular instrument.

We ask you to keep the coupon during the warranty period. When purchasing a product, require a full warranty card.

Warranty service is carried out only if there is a correctly and clearly filled original warranty card, which indicates: the product model, date of sale, serial number, warranty service period, and the seller’s seal. *
The service life of household appliances is 5 years.
The product is intended for consumer use. When using the product in commercial activities, the seller/manufacturer does not bear warranty obligations, and after-sales service is performed on a paid basis.
Warranty repair is carried out within the period specified in the warranty card for the product in an authorized service center on the conditions and terms determined by applicable law.
The product is withdrawn from the warranty in case of violation by the consumer of the operating rules set forth in the instruction manual.
The product is removed from warranty service in the following cases:
- misuse and non-consumer use;
- mechanical damage;
- damage caused by the ingress of foreign objects, substances, liquids, and insects;
- damage caused by natural disasters (rain, wind, lightning, etc.), fire, domestic factors (excessive humidity, dust, aggressive environment, etc.)
- damage caused by non-compliance of power and cable network parameters with state standards and other similar factors;
- when operating equipment in the power supply network with a missing single ground loop;
- in case of violation of seals installed on the product;
- lack of a serial number of the device, or inability to identify it.
The warranty does not cover consumables and accessories, as well as filters, shelves, drawers, stands, and other containers for storing products.
The warranty period is 12 months from the date of sale.