EBECO EB-Therm 800 Multifunctional 4 in 1 Digital Thermostat For DIN Rail Mounting Instruction Manual
- June 27, 2024
- EBECO
Table of Contents
EBECO EB-Therm 800 Multifunctional 4 in 1 Digital Thermostat For DIN Rail
Mounting
Specifications:
- Product Name: EB-Therm 800
- Type: Multifunctional 4 in 1 digital thermostat for DIN-rail mounting
- Temperature Range: 10°C to 42.5°C
- Certifications: EMC/2500 VAC, RoHS, WEEE, CB
Product Usage Instructions
Installation:
- Connect incoming phase and neutral to terminals 1 and 2.
- Connect Sensor A to terminals 5 and 6, and Sensor B to terminals 7 and 8.
- Connect possible external alarm to terminals 10 and 11.
Operation Mode:
The thermostat can operate in different modes like HOME, OFFICE, VACATION,
etc. Select the desired mode from the menu.
Sensor Configuration:
You can connect up to two temperature sensors (Sensor A & Sensor B) and one
moisture sensor (Sensor C) to monitor the temperature and humidity levels.
Follow the wiring diagram for
sensor connections.
Remote Control:
A remote control unit can be connected to control the thermostat settings.
Refer to the manual for remote control instructions.
FAQ:
-
How many sensors can be connected to the thermostat?
You can connect a maximum of one moisture sensor (Sensor C) and one temperature sensor (either Sensor A or Sensor B). -
Can I control the thermostat remotely?
Yes, you can control the thermostat using a remote control unit connected to the designated terminal blocks. Ensure proper wiring as per the instructions provided.
Thank you for choosing Ebeco and EB-Therm 800, which we hope will serve you
well for a long time to come.
This is a quick guide – a more detailed description, in a choice of languages,
is available in the EB-Therm 800 Manual at ebeco.com.
The product is covered by the guarantee conditions and must be installed and
used according to the manual. This applies to both the installation
electrician and the user of the product.
If you have any questions, you are welcome to contact us at Ebeco.
Call +46 31 707 75 50 or send an e-mail to
support@ebeco.se.
Included in the package
- Thermostat E 85 816 10
- Quick guide
- Sensor cable 3 m E 85 816 71
Accessories
- Sensor cable, high temperature 3 m (for temperatures above +75°C to 150°C ) E 85 816 73
- Sensor cable, low temperature 6 m (for temperatures below +75°C) E 85 816 84
- Encapsulated sensor IP20 / 54 E 85 816 22
- Roof sensor, moisture E 89 350 75
- Ground sensor, moisture and temperature E 85 801 01
Overview
Operation mode
2 The program can be controlled via a remote control unit connected to the designated terminal blocks. See wiring diagram. The thermostat switches to the set temperature when the input circuit is closed and when the input circuit opens the thermostat returns to the previous temperature setting, after the set delay time where applicable.
Installation
The incoming phase and neutral are connected to terminals 1 and 2.
Terminals 3 and 4 are the relay that regulates the load.
Sensor A is connected to 5 and 6.
Sensor B is connected to 7 and 8.
A possible external alarm (max. 2A, 120VAC) is connected to terminals 10 and
11.
Sensor C (moisture) is connected to 12 and 13.
A possible remote control unit is connected to 9 and 14.
Start menu
Menus & functions
The functions in EB Therm 800 are arranged in a system of menus and submenus. The MAIN MENU always contains three submenus TEMP, PROGRAM and SYSTEM. There are further choices under these. The menus are reached by pressing in the display mode.
H = Operation mode HEATING, C = Operation mode COOLING, I = INDUSTRY, M = Operation mode MAX/MIN
Display mode
- CURRENT VALUE A shows the temperature at sensor A, CURRENT VALUE B shows the temperature at sensor B. CURRENT VALUE C shows if moisture is detected by the sensor. The current value is only shown for sensors that are installed and activated.
Technical data
- Voltage 230 VAC – 50 Hz
- Temperature range -20 °C to +150 °C
- Break-off capacity 3680 W/16 A/230 VAC
- Power consumption 2.5 W
- Connection cable max 2.5 mm²
- Loading cos φ = 1
- Connection difference Adjustable +/- 0.3 to 10.3 °C
- Encapsulation class IP20
- Reserve power 50 hours
- Max length, sensor cable 50 m, 2×1.5 mm²
- Alarm relay 2 A/120 VAC Normal connection
- Installation Standard DIN-rail EN 50022-35
- Ambient temperature -20 °C to +45 °C
- Test value for low or high temperature sensors
CERTIFICATION: EMC/2500 VAC RoHS WEEE CB
EB-Therm 800 is a high current unit and must therefore be installed according
to applicable regulations and be approved by an authorised electrician.
EBECO AB
Lärjeågatan 11
SE-415 02 Göteborg, SWEDEN
Phone +46 31 707 75 50
ebeco.com
info@ebeco.se
Snabbguide-EB-Therm-800-240610
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>