LEXIN LX-Q3 Motorcycle Bluetooth Speaker User Guide

LEXIN LX-Q3 Motorcycle Bluetooth Speaker User Guide

Features

• Heavy duty metal housing
• Bluetooth v5.1
• Unique built-in LED turn light
• 150W peak power output, premium stereo sound
• Plug-in-Play audio system
• Built-in 3 inch full-range speaker
• Built-in FM Radio
• 3 button control, easy operation
• IP67 waterproof design
• USB interface can be used for music stream and mobile phone charging
• Fit for 7/8″ to 1 1/4″ handlebar
• Dual EQ Sound Mode, Loud Tune and Bass Enhancement
• Bluetooth Music Sharing

Product Packaging

• LX-Q3 Speaker (Main and Slave Speaker)
• Power Cord x1
• User Manual
• Screw x4
• Zip Ties x5
• Bushing Parts x4
• Antenna x1
• Allen Wrench xl

Installation Instructions

Before installation, please connect the power cord or the SAE connector to the 12V power source to test the Speaker first.

Step (1) Install the speakers:

Choose a suitable location to install the speakers, Use the appropriate bushing and screws to mount the speakers on the handlebar.The main speaker is installed on the left side of the motorcycle, and the slave speaker is installed on the right side of the motorcycle.

Note: There are two screws in the base of the speaker, you can use the Allen Wrench to loosen the screws to adjust the angle of the speaker, and then tighten it.

Step (2) Connect the Speakers:

Plug the speaker connector of the main speaker to the slave speaker, and please pay attention that the two arrows on each connector indicate the right connection.

Step (3) Connect to the Turn Signal light:

Peel off the insulated wrap of the red (right) and white (left) wires, and then connect it with the turn signal from the motorcycle. Pay attention to the correct connection of the left and right turn signals.

Step (4) Connect SAE Power Source:

Connect the red terminal of the power cord to the positive pole of the motorcycle battery, and the black terminal to the negative pole of the motorcycle battery, plug the SAE connector into the SAE connector of the main speaker, and then tie the excess cables together and hide them.

Note: If the speaker cannot power on normally, please check whether the fuse is burned out. If so, please disconnect the power supply of the speaker, and replace a new fuse, then reconnect the power supply and it will work again.

Step (5) Install FM Radio Antenna:
Connect the external radio antenna to the antenna connector on the main speaker. Find a place to locate the antenna with 3M tape on the motorcycle, and extend the external antenna for FM reception when used.

Basic Operation

Power On

Press and hold the Power Button for about 1 second, The speaker will report “Bluetooth Mode” and enter pairing mode. The indicator light will flash green and blue simultaneously for 1 second.
Note:

1. When power on, the device will default to Bluetooth mode and automatically enter the Bluetooth pairing mode, the blue indicator light will flash quickly. After the pairing is completed, the blue indicator light will fade in and out.
2. Every time you turn on the speaker, it will automatically search and connect with the last paired device.

Power Off

Press and hold the Power Button for about 3 seconds, The speaker will report “Power Off11 and the indicator light will keep flashing blue for 1 second then turn off.

Switch Mode

Double click the Power Button to cycle switch three modes between Bluetooth /FM/ USB Music with voice prompt.

Dual Bluetooth Mode

LEXIN Q3 can connect with up to two different Bluetooth devices at the same time.

• Turn off the Bluetooth on the first paired device, and it will automatical­ly enter into pairing status.
• Turn on the Bluetooth of the second mobile phone or other audio sources, search for LX-Q3, and then click it for pairing, the LED light will flash blue quickly.
• After the pairing is completed, the blue LED light will fade in and out.

Note: If the speaker is not connected to a device within 5 minutes,the system will automatically power off.

USB Mode
When power on, double-click the Power Button to switch to the USB mode, and the LED light will turn to Green, then plug the USB drive with audio source into the USB port.

Note: While in USB mode, the speaker will automatically shut down after 15 minutes if you pause the music . It is recommended that the USB disk only stores audio files.

FM Radio Mode

When power on, double-click the power button to switch to the FM radio mode, and the LED light will turn to Green, single click the power button to enter the automatic searching mode, and it will automatically save the radio station.

Music Control

Click the Volume Up Button for the previous song, click the Volume Down Button for the next song. In FM radio mode, click the Volume Up Button to track forward, click the Volume Down Button to track backward. Click the Power Button to pause or play music.

Volume Control

Press and hold the Volume Up Button to increase the volume, press and hold the Volume Down Button to reduce the volume.

Note: Volume control is only effective while music and FM radio is playing.

Turn Signal/Running Lights

Running light: Double click the Volume Up Button to turn on/off the running light.
Turn signal light: It is optional depending on if you connect the wire to the motorcycle turn signal.

Note:

1. The LED running light is on as a default setting.
2. When the turn signal wires are connected with the motorcycle, the running light will be automatically controlled by the motorcycle turn light signal.

Switch Bass Enhancement Sound Mode

When in USB and Bluetooth mode: Double click the Volume Down Button to cycle change the EQ sound mode between Loud Tune and Bass Enhancement. The default mode is Loud Tune for outdoor use, and the last setting will not be set in memory.

Power Saving Mode

The system will automatically shut down after 5 minutes in the standby mode if no operation.

Bluetooth Music Sharing Mode

In Bluetooth mode, 2 sets of Q3 speakers will simultaneously play the same music through the connected mobile phone.

Turn on Music Sharing Mode

When the 2 sets of Q3 speakers are both in Bluetooth standby mode, triple click the power button of the first Q3 main speaker, it will automatically search and connect with the second Q3 speaker.

After the two Q3s are connected, the first Q3 speaker can stream music and control the full functions, such as play and pause the music, volume up and volume down, and change songs. While the second Q3 speaker can only control the volume up and volume down.

Turn off Music Sharing Mode

Triple-click the power button to turn off the Music Sharing mode.

Note:

1. The music sharing function is only applicable when you have 2 sets of Q3 speakers.
2. The music sharing function can only be used in Bluetooth mode.

Technical Information

• Bluetooth: VS.I
• Input power: DC12V
• Class D digital amplifier: 2*25W
• WidthHeightDepth = 90173122 MM
• Frequency response range: 80–16000Hz
• Audio source type: Bluetooth, FM, USB_HOST
• Peak power: ISOW
• Signal-to-noise ratio: >BOdB

Troubleshooting

Maintenance and Care

Please follow the following suggestions for optimal maintenance of LEXIN Q3 device and maintain warranty protection:

When cleaning the LEXIN Q3 external body, do not use a high-pressure water gun to wash the horn part, avoid to damage the horn;

****It must be confirmed that the power supply voltage is consistent with the Q3 device before use it, please use it under a suitable voltage of 12V;

****Do not use the Q3 device for a long time without power on the motorcycle’s engine, to avoid running out the motorcycle battery, which will cause the voltage to be too low to start the motorcycle;

****Do not install the power cord with wet hands to avoid electric shock When replacing the fuse of the Q3 device, it should be replaced strictly according to the requirements, and it is strictly forbidden to use unqualified replaced fuse;

****Do not store the device in a high temperature area or humid environment;

****Do not store the device in cold temperature areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.

****Do not drop or knock the device. Rough handling can break internal circuit boards and fine mechanics.

****Do not let metal conductive materials such as iron needles, hairpins, coins, etc, fall into the Q3 device to avoid damage to the device;

****Do not use the Q3 device under overload or short circuit conditions;

****Do not attempt to open the case of LEXIN Q3 device.

****Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.

****Do not use or store the device in dusty or dirty environments. Moving parts and electronic components can be damaged.

****Do not paint the device. Paint can clog the moving parts and prevent proper operation.

****Pay attention to avoid the all the wire being stepped on and being crushed by heavy objects;

****Do not forcefully pull, plug or twist the power cord.

Note: Do not use a high-pressure water  gun to wash the horn part, avoid to damage the horn.

Warranty

LEXI N warrants that this product shall conform to and perform in accordance with published technical specifications and the accompanying written materials, and shall be free of defects in materials and workmanship, for a period of Two years from the date of purchase by the first consumer purchaser of the Product. The limited warranty extends only to the original consumer purchaser of the Product and is not assignable or transferable to any subsequent purchaser/end-user.

This warranty is limited to the repair or replacement, at LEXI N’s discretion, of defective or non-conforming Product, and LEXIN shall not be responsible for the failure of the Product to per form specified functions, or any other non- conformance caused by or attributable to:

(a) any misapplication or misuse of the Product;
(b) failure of Customer to adhere to any of LEXI N’s specifications or instructions;
(c) neglect of, abuse of, or accident to, the Product; or
(d) any associated or complementary equipment or software not furnished by LEXIN.

Limited warranty service may be obtained by delivering the Product to LEXI Nor to the international distributor it was purchased through and providing proof of purchase or receipt date.Customer agrees to insure the Product or assume the risk of loss or damage in transit, to prepay shipping charges to LEXIN, and to use the original shipping container or eq u iva lent.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2.  This device must accept any interference, including interference that may cause undesired operation of the device.

This EUT is compliance with SAR for general population/uncontrolled exposure limits in IC RSS-102 and had been tested in accordance with the measurement methods and procedures specified in IEEE 1528 and IEC 62209. This equipment should be installed and operated with minimum distance 10 mm between the radiator and your body. This device and its antenna(s)must not be co-located or operating in conjunction with any other antenna or transmitter.

Lexin Electronics Inc.

1(800) 380 – 8248

www.lexin-moto.com

Backed by 2-Year Warranty

For technical support:

tech@lexinmotorcycle.com

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>