LOREX LK101-Z Bluetooth Deadbolt Smart Lock Installation Guide

LOREX LK101-Z Bluetooth Deadbolt Smart Lock

What’s Included

Tools Needed

• Philips Head Screwdriver
• Flathead Screwdriver
• Pencil
• Drill
• Spade Drill Bit
• Mortise Chisel
• Hammer
• Wooden Block
• Pliers

Optional

DOOR TEMPLATE

Door Preparation

1. Check that pre-drilled holes in the door match the sizes on the door template before installation.
   WARNING! Only drill into the door if you are skilled in safe drill operation and fully understand the steps.

2. Drill the holes. To prevent wood splitting, drilling from both sides of the door.

3. Chisel out a mortise 5/32” (3 mm) deep. Note: If you prefer not to chisel, an alternative installation method using the drive-in collar will be explained later.

4. Prepare the door jamb by using the strike plate as a guide. Drill latch and screw holes, then chisel out a mortise until the strike plate fits flush. Door jamb hole size.

   • 1-3/16″ (30 mm)
   • 1-9/16″(40 mm)
   • 1″ (25 mm)
   • Strike plate size
   • 5/32″ (4 mm)
   • 2-3/4″ (70 mm)
   • 1-1/8″ (28 mm)

5. Attach the dust box and reinforced strike plate to the door jamb using the 3″ (76 mm) screws (2×).

6. Attach the strike plate using the 3/4″ (19 mm) screws (2×)

Latch Installation

1. Install the correct faceplate. To prepare for the no-chisel drive-in collar method, remove the pre-installed outer plate from the latch using a flathead screwdriver, and slide off the inner plate. Attach the drive-in collar.
2. Adjust the latch backset length by twisting it 180°. CAUTION! Ensure the cam latch is positioned “UP” before adjusting the backseat.
3. Install the latch using the 3/4″ (19 mm) wood screws (2×). Tap latch flush. Use a wooden block (not included) between the hammer and the drive-in latch to prevent damage.

Lock Assembly Installation

1. The door bore size options: Ø 2-1/8” (54 mm)For Ø 1-1/2” (38 mm) Use pliers and a flathead screwdriver to remove the pre-installed mounting plate pieces to prepare for installation.
2. Install the lock assembly:
   • Ensure the latch bolt is retracted.
   • Thread the cable through the hole and under the latch. Place the exterior lock assembly against the door.
   • Position the raised part of the mounting plate against the door.
3. Slide the cable through the notch in the mounting plate.
   • Attach the mounting plate against the door using the 1-1/4″ (31.7 mm) screw and the 2-1/16″ (52 mm) mounting bolts (2×).
4. Remove the battery cover.
5. Securely attach the power cable to the connector port, ensuring the metal side faces outward.
6. Neatly arrange the cable inside.
7. Rama. Attach the interior assembly to the door by inserting and tightening the 3/4″ (19 mm) screws (2×).

Admin Code Setup

Batteries

1. Install 4 AA alkaline batteries.
   CAUTION! Use 4 AA alkaline batteries for best performance.

2. Attach battery cover.

Admin Code
Setting the Admin  Code can be done in Code can be done in two ways:

1. Scan the QR code to download the mobile app, then tap the + icon to add the smart lock.
2. Scan the smart lock’s QR code.
3. Press the SET button.
4. Follow the in-app steps to set the admin code
5. Once finished, the lock will automatically change the bolt direction.

Overview

1. Status Indicators
2. Button: Press to lock from outside.
3. Clear Button: Press to cancel typos or exit programming mode.
4. Keyhole: Lock or unlock with the key.
5. Battery Cover: Protects battery compartment.
6. SET Button: Hold for 1 second to enter programming mode. Press again to exit.
7. Interior Thumbturn: Turn to lock or unlock from inside.

Locking & Unlocking

To lock

To unlock

Programming
To start programming, set up the Admin Code. If you hear 3 beeps, it indicates an incorrect entry, so please retry the step.

Change Admin Code

• Programs or unlocks the smart lock
• 4-8 digits

Factory Reset
Resetting clears all data, including bolt direction.

1. Remove 1 battery.
2. Hold the SET button and reinsert the battery. Continue to hold SET until you hear a song beep.

Safety Guidelines
CAUTION! Use 4 AA alkaline batteries for best performance. Follow the instructions in this guide before installation and use.

• Do not disassemble internal components as it will void the limited warranty.
• Do not drop or be subject to heavy impact to prevent permanent damage.
• Ensure no water or liquids enter the smart lock during installation.
• Do not use pins or sharp objects on the keypad.
• Back up essential information such as admin and entry codes.

Care & Maintenance

• Remove or refrain from installing the smart lock before painting the door.
• Regularly clean using mild soap and a soft cloth.
• Do not use abrasive or chemical products containing alcohol, benzene, or acids, as they may damage the smart lock.
• Do not use sharp or abrasive objects during cleaning.

Need help?
Scan the below QR code for additional support material. help.lorex.com/LK101-series

Register your product
Please see our full Terms of Service and Limited Hardware Warranty Policy at:

Regulatory Information

IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p) is not more than that necessary for successful communication.

The user manual for local area network devices shall contain instructions related to the restrictions mentioned in the above sections, namely:
(i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and (iii) the maximum antenna gain permitted for devices in the band 5725- 5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650- 5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.

FCC Statement

Please pay attention that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
   Caution : The user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF exposure warning
This equipment must be installed and operated according to the provided instructions and antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. The equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. For full FCC compliance declarations, visit https://www.lorex.com/pages/fcc-compliance

Copyright © 2024 Lorex Technology Inc
As our products are subject to continuous improvement, Lorex reserves the right to modify product design, specifications and prices, without notice and without incurring any obligation. E&OE. All rights reserved.
lorex.com
help.lorex.com/LK101-series

References

• LK101 Series | LOREX Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>