BOCCHI 2019 0001 XX Kitchen Faucets Instruction Manual

BOCCHI 2019 0001 XX Kitchen Faucets

Tools and Materials:

1. Adjustable Wrench
2. Phillips Head Screwdriver

Hardware (included with the faucet):

Included with all BOCCHI Faucets:

•  Mounting Hardware: rubber seal (1pc.), stainless steel washer (1 pc.), mounting ring (1 pc.), screws (3 pcs.)
•  Retraction Weight (1 pcs.)
•  Pullout Hose (1 pc.)
•  Supply Hoses (1 pc. hot and 1 pc. cold)
• Optional Stabilizer (1 pc.) to be used if the faucet is installed on a thin and flexible countertop or with a stainless steel sink

Optional Hardware (not included with the faucet)

Sold separately. Compatible with all BOCCHI Faucets:

Optional Deck Plate may be used with any BOCCHI Faucet to provide a decorative base to the faucet. All BOCCHI Deck Plates (2180 0003 XX or 2180 0004 XX) fit all BOCCHI Faucets but are sold separately. Designed to fit across a standard 8-inch faucet drilling to hide unnecessary holes, or other unsightly marks. All BOCCHI Deck Plates come with a single center-drilled hole.

Technical Information

• Recommended water pressure= 20 – 75 psi / Maximum water pressure = 145 psi
• Recommended hot water temperature = 1200 – 1400 F /
• Maximum hot water temperature = 1600 F Flow rate = 1.75 gpm maximum
• Necessary hole size in countertop/sink = 1 3/8 inches
• Maximum thickness of countertop/sink = 2 1/2 inches
  •  Pull-down sprayheads are equipped with 2 check valves for backflow prevention.
  •  The supply hoses for the faucets are for use with 3/8 inch service stops. If your service stops are of a different size, purchase adapters at your local home center or plumbing store.

IMPORTANT : It is imperative that you follow all local plumbing codes and standards to assure correct installation and hot water temperature at the water heater.

CAUTION : Do NOT bend or twist the supply hoses! A gentle curve of no less than 2 3/4 inch diameter is allowable for space, however tight bends, kinks, and twisting may result in damage to the hoses.

Before you begin:

•  BOCCHI recommends that this faucet be installed by a licensed professional plumber/installer.
  •

• Please read over the entire installation instructions before beginning the installation.

•  Images in these instructions are generic and may vary slightly from your exact model.

•  Make sure you have all the needed tools and parts to complete the installation. Ensure that the are has been properly prepped for the preferred installation setting.

•  Keep this installation guide and your receipt for proof of purchase and future reference.

•  Care and Cleaning Guides and Warranty information for these faucets may be found at www.bocchiusa.com

•  All information in these instructions is based on the latest product information available at the time of publication. BOCCHI reserves the right to make revisions in the design of products without notice, as specified in the Price Book.

Installation:

• • Double check to be certain that the water is shut off at the service stops before you begin.
  • If necessary, remove the old faucet.
  • Clean the mounting area and surface, and dry thoroughly.
  • Insert the new faucet in the mounting hole. NOTE: If you are using an optional deck plate, install it now. Simply set the deck plate into place over the faucet mounting hole and drop the faucet through the deck plate hole as you also drop it through the countertop hole. Once the faucet is securely installed in place, it will hold the deck plate in place.
  • If using the stabilizer flange, install it now. Stabilizer flanges should be used with thin or flexible countertops, and with stainless steel sinks. The stabilizer should be installed with the flat triangular side facing up, and the tube side facing down, then be slid onto the faucet shaft from underneath the countertop to help stabilize the faucet from below.

•  Slide the mounting hardware onto the shaft of the faucet from the underside keeping the water supply lines inside the mounting ring. The order of mounting hardware should be, starting with the first on, closest to the underside of the countertop: (1st) rubber seal,(2nd) stainless steel washer, (3rd) mounting ring.

•  Tighten the mounting ring and all parts and insert the 3 screws provided with the faucet into the 3 corresponding holes on the mounting ring. Tighten using the Phillips head screwdriver. CAUTION: Do NOT over tighten or use a power drill to tighten the screws.

• Connect the pullout hose into the quick connection.

• Install the weight to the pullout hose above the loop on the pullout side. Install by unscrewing the screws holding the barrel of the weight closed. Open the weight and enclose the pullout hose into the fitted opening inside the weight. Finish by securely closing the weight and replacing the screws to hold it closed, enclosing the pullout hose within.

•  Attach the water supply lines to the hot and cold service stops and turn on the water. The hot supply line can be identified by red markings on the supply line, and the cold supply line by blue markings; some hoses may have both red and blue markings and are suitable for use with either line.

•  Remove the spray-head, by gently pulling it down and twisting clockwise to unscrew it from its connection. Hold the hose and be sure to aim the water stream into the bottom of the drain to reduce splashing. Run the water for 1-2 minutes at a mixed temperature to remove any dirt or debris that may be in the line and could damage the spray-head.

•  Reattach the spray-head and check for leaks.

User Control Guide:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>