ise KNX-IoT Gateway Smart Connect Instruction Manual
- June 26, 2024
- ise
Table of Contents
ise KNX-IoT Gateway Smart Connect
Safety notes
Only qualified electricians may install and mount electrical. Failure to
observe the installation guide can result in damage to the device, fire or
other dangers. This installation guide is an integral part of the product and
must remain with the customer.
SMART CONNECT KNX
Device design (fig. 1)
- Programming button
- Connection : KNX
- Connection : External power supply
- Programming LED
- APP = application status indicator
- COM = KNX/TP communication
- Network connection: 2x RJ45 socket
- Release lever for top-hat rail terminal
- microSD card slot
Function
System information
This device is a KNX system product and complies with the KNX guidelines.
Detailed specialist knowledge gained on KNX training courses is required to
understand the device. The device’s function depends on the software. Detailed
information about software versions, specific ranges of functions, and the
software itself can be found in the manufacturer’s product database. KNX-
certified ETS software is used to plan, install and commission the device. You
will find the product database and technical descriptions on our website at
www.ise.de.
Proper use
The gateway serves as an interface to integrate the compatible external device
into the KNX system. Gateways with my. is access also provides remote access
to the KNX system. You will find information on specific functions and their
proper use in the associated product manual available on the relevant product
page at www.ise.de.
Information for electricians
Mounting and electrical connection
DANGER!
You are at risk of electric shock if you touch live parts in the installation
area. Electric shock can cause death. Isolate before working on the device and
cover up live parts in the vicinity
Installation and electrical connection (fig. 1)
The device is intended for fixed installation in indoor spaces and dry rooms.
The device and the devices connected to it in a network must be installed in
the same earthing system.
- Observe the temperature range.
- Ensure sufficient cooling.
- Use protection class II for external power supply.
- Ensure safe separation between Ethernet and mains voltage.
-
Snap the device onto a top-hat rail according to DIN EN 60715. See Figure 1 for the installation position.
-
Connect the external power supply to the connection terminal (3).
Recommendation : Use a white-yellow connection terminal. -
Connect the KNX line with the red-black bus terminal (2).
-
Establish network connection by plugging RJ45 plug into RJ45 socket (7).
Attaching the cover cap (fig. 2)
A cover cap must be attached to protect the bus connection from dangerous
voltages in the connection area.
- Route bus line to the rear.
- Attach the cover cap over the connection terminals until it engages.
Figure 2: Attach the cover cap
Removing the cover cap (fig. 3)
Press the cover cap on the sides and remove it.
Commissioning
- Briefly press the programming button (1). Programming LED (4) lights up.
- Assign individual addresses. Programming LED (4) goes out.
- Label the device with the individual address.
- Load application software, parameters, etc.
Technical data
- Rated voltage: DC 24 V to 30 V SELV
- Power consumption : 2 W
- KNX :
- Connection : Bus connection terminal
- Medium : TP1, S-Mode
- Current consumption: typ. 6 mA
- IP :
- Connection 2× RJ45
- Communication : Ethernet 10/100 BaseT (10/100 Mbit/s)
- Ambient temperature: 0 °C to +45 °C
- Storage temperature: -25 °C to +70 °C
- Dimensions : 2 HP (DRA plus)
Disposal
Devices with this symbol must be disposed of separately from unsorted
municipal waste. Delete any personal data by executing a factory reset before
disposal. Please contact our support team before you send a device back.
ise
- Individuelle Software und Elektronik GmbH
- Osterstraße 15
- 26122 Oldenburg
- Germany
- www.ise.de
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>