ise S-0001-006 Smart Connect KNX VAILLANT gateway set User Manual

Name

Direction

Data width

DP type

Flags (CRWTU)

Cooling days ­ manual cool- Write ing

1 bytes

5.010 CRWT-

Data type:

Counter pulse

Sets and reads the number of days for manual cooling. Cycle time: max. 35 seconds multiMATIC value range: 0-99 days

sensoCOMFORT value range: 0-255 days

This communication object is visible when a Vaillant heat pump is available and the cooling function is activated for at least one heating circuit in the sys-
tem controller.

Parameters > System dimensioning > Heat generator > A Vaillant heat pump is available and Parameters > System dimensioning > Heating circuit N > A heating circuit N is available for room heating and Parameters > System dimensioning > Heating circuit N > The cooling function for circuit N is activated on the system controller and Parameters > Use cases > Smart control > I would like to be able to configure hot water heating and heating in my visualisation with time control <> and Parameters > Time settings > Manual cooling function > Set cooling time > Number of cooling days <>

If a value outside the value range is written to this communication object, error code 7 is sent to communication object 12.

Order No. S-0001-006

Product Manual Page 37 (81)

Object
35
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Cooling interval ­ start

Write

3 bytes 11.001 CRWT-

Data type:

Date

Sets and reads the start of the cooling interval. Cycle time: max. 35 seconds multiMATIC value range: max. 99 days between CO35 and CO36

sensoCOMFORT value range: DD.MM.YY

This communication object is visible when a Vaillant heat pump is available and the cooling function is activated for at least one heating circuit in the sys-
tem controller.

Parameters > System dimensioning > Heat generator > A Vaillant heat pump is available and Parameters > System dimensioning > Heating circuit N > A heating circuit N is available for room heating and Parameters > System dimensioning > Heating circuit N > The cooling function for circuit N is activated on the system controller and Parameters > Use cases > Smart control > I would like to be able to configure hot water heating and heating in my visualisation with time control <> and Parameters > Time settings > Manual cooling function > Set cooling time > Cooling interval <>

Order No. S-0001-006

Product Manual Page 38 (81)

Object
36
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Cooling interval ­ end

Write

3 bytes 11.001 CRWT-

Data type:

Date

Sets and reads the end of the cooling interval.
Cycle time: max. 35 seconds multiMATIC value range: max. 99 days between CO36 and CO35 sensoCOMFORT value range: DD.MM.YY

This communication object is visible when a Vaillant heat pump is available and the cooling function is activated for at least one heating circuit in the sys-
tem controller.

Parameters > System dimensioning > Heat generator > A Vaillant heat pump is available and Parameters > System dimensioning > Heating circuit N > A heating circuit N is available for room heating and Parameters > System dimensioning > Heating circuit N > The cooling function for circuit N is activated on the system controller and Parameters > Use cases > Smart control > I would like to be able to configure hot water heating and heating in my visualisation with time control <> and Parameters > Time settings > Manual cooling function > Set cooling time > Cooling interval <>

Order No. S-0001-006

Product Manual Page 39 (81)

Object
50
Rubric: Function: Description:
Object
51
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Energy yields ­ solar yield Read

4 bytes 13.013 CR-T-

Data type:

Active energy (kWh)

Provides the accumulated solar yield which was read during the last query. Cycle time: max. 9 minutes Updating in the controller: up to 24 hr

This communication object is visible when the thermal solar yield from a solar thermal system is to be displayed. The requirement for this is that the system controller must record the data and the corresponding use case must be selected.
Parameters > System dimensioning > Solar thermal system > A solar thermal system is available, (…) and Parameters > Use cases > Information > I would like to see the energy yield of my heat pump and solar thermal system (…) <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Energy yields ­ environmental yield

Read

4 bytes 13.013 CR-T-

Data type:

Active energy (kWh)

Provides the accumulated environmental yield which was read during the last query. Cycle time: max. 9 minutes Updating in the controller: up to 24 hr

This communication object is visible when the environment yield of a Vaillant heat pump is to be displayed. The requirement for this is that the system controller must record the data and the corresponding use case must be selected.
Parameters > System dimensioning > Heat generator > A Vaillant heat pump is available (…) and Parameters > Use cases > Information > I would like to see the energy yield of my heat pump and solar thermal system (…) <>

Order No. S-0001-006

Product Manual Page 40 (81)

Object
52
Rubric: Function: Description:
Object
53
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Energy consumption ­

Read

consumption gas for heating

4 bytes 13.013 CR-T-

Data type:

Active energy (kWh)

Provides the accumulated gas consumption for heating which was read during the last query. Cycle time: max. 9 minutes Updating in the controller: up to 24 hr

This communication object is visible if a Vaillant gas boiler is available, the system controller records the data and the corresponding use case was selected.

Parameters > System dimensioning > Heat generator > A Vaillant gas boiler is available and Parameters > System dimensioning > Sensors > The system controller shows the fuel consumption (gas consumption) (…) and Parameters > Use cases > Information > I would like to be able to see the energy consumption (…) <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Energy consumption ­ consumption gas for hot water

Read

4 bytes 13.013 CR-T-

Data type:

Active energy (kWh)

Provides the accumulated gas consumption for hot water which was read during the last query. Cycle time: max. 9 minutes Updating in the controller: up to 24 hr

This communication object is visible if a Vaillant gas boiler is available, the system controller records the data and the corresponding use case was selected.

Parameters > System dimensioning > Heat generator > A Vaillant gas boiler is available (…) and Parameters > System dimensioning > Sensors > The system controller shows the fuel consumption (gas consumption) (…) and Parameters > Use cases > Information > I would like to be able to see the energy consumption (…) <>

Order No. S-0001-006

Product Manual Page 41 (81)

Object
54
Rubric: Function:
Description:
Object
55
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Energy consumption ­ consumption electricity for heating

Read

4 bytes 13.013 CR-T-

Data type:

Active energy (kWh)

Provides the accumulated current consumption for heating which was read during the last query. Cycle time: max. 9 minutes Updating in the controller: up to 24 hr

This communication object is visible when the system controller displays the consumption (electricity consumption) and the corresponding use case has been selected.

Parameters > System dimensioning > Sensors > The system controller shows the consumption (electricity consumption) (…) and Parameters > Use cases > Information > I would like to be able to see the energy consumption (…) <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Energy consumption ­ consumption electricity for hot water

Read

4 bytes 13.013 CR-T-

Data type:

Active energy (kWh)

Provides the accumulated current consumption for hot water which was read during the last query. Cycle time: max. 9 minutes Updating in the controller: up to 24 hr

This communication object is visible when the system controller displays the consumption (electricity consumption) and the corresponding use case has been selected.

Parameters > System dimensioning > Sensors > The system controller shows the consumption (electricity consumption) (…) and Parameters > Use cases > Information > I would like to be able to see the energy consumption (…) <>

Order No. S-0001-006

Product Manual Page 42 (81)

ise smart connect KNX Vaillant
Configuration
Important note:
The sensoCOMFORT and multiMATIC system controllers provide different HVAC operation modes. You will find the assignment to the KNX operation modes in the table:

KNX Building Protection
Auto Comfort Economy Standby

sensoCOMFORT Off
Time Controlled Manual Manual Manual

multiMATIC Off Auto Day
Setback Setback

The following applies to the sensoCOMFORT system controller:
· The last KNX operating mode selected which leads to activation of “Manual” controller mode, is stored internally. The “Comfort” controller mode is used initially.
· The setpoint temperatures “Day temperature heating” and “Set-back temperature heating” are used by the sensoCOMFORT system controller as data points for the KNX to set the “Manual temperature” on the controller when the KNX operating mode is switched. No controller temperature value is sent to any of these communication objects. The previously configured setpoint value is used when the ise smart connect KNX Vaillant is restarted.
· Changing the manual temperature value on the system controller does not result in any changes to the KNX.

Order No. S-0001-006

Product Manual Page 43 (81)

Object
60
Rubric: Function:
Description:
Object
61
Rubric: Function: Description:

ise smart connect KNX Vaillant
Configuration

Name
Heating zone 1 ­ operation mode

Direction
Write
Data type:

Data width
1 bytes

DP type
20.102

Flags (CRWTU)
CRWT-

HVAC mode

Sets and reads the operation mode of heating zone 1. You will find the assignment of KNX operation modes to the system controller in the table on page 43. For communication object 63, the assignment is set to the last “Standby” or “Economy” value sent. Cycle time: max. 35 seconds
This communication object is visible when a heating circuit 1 is available and the corresponding use case has been selected.
Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 1 ­ “Auto” oper- Write ation mode

1 bit

1.011 CRWT-

Data type:

Status

Activates the “Auto” operation mode for heating zone 1 or shows whether this is active. Corresponds to “Auto” of data type HVAC mode.

Cycle time: max. 35 seconds

This communication object is visible when a heating circuit 1 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Order No. S-0001-006

Product Manual Page 44 (81)

Object
62
Rubric: Function: Description:
Object
63
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 1 ­ “Day” oper- Write ation mode

1 bit

1.011 CRWT-

Data type:

Status

Activates the “Day” operation mode for heating zone 1 or shows whether this is active. Corresponds to “Comfort” of data type HVAC mode.

Cycle time: max. 35 seconds

This communication object is visible when a heating circuit 1 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 1 ­ “Night” op- Write eration mode

1 bit

1.011 CRWT-

Data type:

Status

Activates the “Night” operation mode for heating zone 1 or shows whether this
is active. Corresponds to “Economy” or “Standby” of data type HVAC mode. The last value written on communication object 60 is decisive for this state. “Economy” is used as standard.

Cycle time: max. 35 seconds

This communication object is visible when a heating circuit 1 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Order No. S-0001-006

Product Manual Page 45 (81)

Object
64
Rubric: Function: Description:
Object
65
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 1 ­ “Off” opera- Write tion mode

1 bit

1.011 CRWT-

Data type:

Status

Activates the “Off” operation mode for heating zone 1 or shows whether this is active. Corresponds to “Building Protection” of data type HVAC mode. Cycle time: max. 35 seconds

This communication object is visible when a heating circuit 1 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 1 ­ day temper- Write ature heating

2 bytes

9.001 CRWT-

Data type:

Temperature (oC)

Sets and reads the current setpoint value for the day temperature in heating
zone 1.
multiMATIC cycle time: max. 35 seconds See note on page 43 for sensoCOMFORT Value range: 5-30 °C

This communication object is visible when a heating circuit 1 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > Use cases > Smart control > I would like to be able to configure hot water heating and heating (…) with time control <>

If a value outside the value range is written to this communication object, error code 7 is sent to communication object 12.

Order No. S-0001-006

Product Manual Page 46 (81)

Object
66
Rubric: Function:
Description:
Object
67
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 1 ­ set-back temperature heating

Write

2 bytes

9.001 CRWT-

Data type:

Temperature (oC)

Sets and reads the current setpoint value for the night temperature in heating zone 1. Cycle time: max. 35 seconds See note on page 43 for sensoCOMFORT Value range: 5-30 °C

This communication object is visible when a heating circuit 1 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > Use cases > Smart control > I would like to be able to configure hot water heating and heating (…) with time control <>

If a value outside the value range is written to this communication object, error code 7 is sent to communication object 12.

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 1 ­ day temper- Write ature cooling

2 bytes

9.001 CRWT-

Data type:

Temperature (oC)

Sets and reads the current setpoint value for the day temperature cooling in heating zone 1. Cycle time: max. 35 seconds Value range: 15-30 °C

This communication object is visible if a Vaillant heat pump and a heating circuit 1 is available, the cooling function is activated in the system controller and
the corresponding use case has been selected.

Parameters > System dimensioning > Heat generator > A Vaillant heat pump is available and Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > System dimensioning > Heating circuit 1 > The cooling function for circuit 1 is activated on the system controller and Parameters > Use cases > Smart control > I would like to be able to configure hot water heating and heating (…) with time control <>

If a value outside the value range is written to this communication object, error code 7 is sent to communication object 12.

Order No. S-0001-006

Product Manual Page 47 (81)

Object
70
Rubric: Function:
Description:
Object
71
Rubric: Function: Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 1 ­ flow tem- Read perature

2 bytes

9.001 CR-T-

Data type:

Temperature (oC)

Displays the current flow temperature in heating circuit 1. Cycle time: max. 3 minutes Value range: 0-99 °C

This communication object is visible when a heating circuit 1 and a heating circuit 2 is available and the corresponding use case has been selected.
Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…) <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 1 ­ setpoint flow temperature

Read

2 bytes

9.001 CR-T-

Data type:

Temperature (oC)

Displays the current setpoint flow temperature in heating circuit 1. Cycle time: max. 3 minutes Value range: 0-99 °C

This communication object is visible when a heating circuit 1 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…) <>

Order No. S-0001-006

Product Manual Page 48 (81)

Object
72
Rubric: Function: Description:
Object
73
Rubric: Function: Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 1 ­ pump

Read

1 bit

1.011 CR-T-

Data type:

Status

Displays the operating state of the pump in heating circuit 1. Cycle time: max. 3 minutes

This communication object is visible when a heating circuit 1 and a heating circuit 2 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…) <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 1 ­ heating curve

Read

2 bytes

9.031 CR-T-

Data type:

2-byte floating decimal value

Displays the value of the setpoint heating curve parameter. Cycle time: max. 3 minutes Value range: 0.1-4

This communication object is visible when a heating circuit 1 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…) <>

Order No. S-0001-006

Product Manual Page 49 (81)

Object
74
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 1 ­ minimum flow temperature cooling mode

Read

2 bytes

9.001 CR-T-

Data type:

Temperature (oC)

Displays the minimum flow temperature in cooling mode. Cycle time: max. 3 minutes Value range: 7-24 °C The requirement for this is a heating circuit which has the cooling function activated and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 1 > A heating circuit 1 is available for room heating and Parameters > System dimensioning > Heating circuit 1 > The cooling function for circuit 1 is activated on the system controller and Parameters > System dimensioning > Heat generator

A Vaillant heat pump is available and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…)

<>

Order No. S-0001-006

Product Manual Page 50 (81)

Object
75
Rubric: Function:
Description:
Object
76
Rubric: Function: Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 2 ­ operation mode

Write

1 bytes 20.102 CRWT-

Data type:

HVAC mode

Sets and reads the operation mode of heating zone 2. You will find the assignment of KNX operation modes to the system controller in the table on page 43. For communication object 78, the assignment is set to the last “Standby” or “Economy” value sent. Cycle time: max. 35 seconds

This communication object is visible when a heating circuit 2 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 2 ­ “Auto” oper- Write ation mode

1 bit

1.011 CRWT-

Data type:

Status

Activates the “Auto” operation mode for heating zone 2 or shows whether this is active. Corresponds to “Auto” of data type HVAC mode. Cycle time: max. 35 seconds

This communication object is visible when a heating circuit 2 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Order No. S-0001-006

Product Manual Page 51 (81)

Object
77
Rubric: Function:
Description:
Object
78
Rubric: Function: Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 2 ­ “Day” oper- Write ation mode

1 bit

1.011 CRWT-

Data type:

Status

Activates the “Day” operation mode for heating zone 2 or shows whether this is active. Corresponds to “Economy” or “Standby” of data type HVAC mode. The last value written on communication object 75 is decisive for this state. “Economy” is used as standard. Cycle time: max. 35 seconds

This communication object is visible when a heating circuit 2 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 2 ­ “Night” op- Write eration mode

1 bit

1.011 CRWT-

Data type:

Status

Activates the “Night” operation mode for heating zone 2 or shows whether this is active. Corresponds to “Comfort” of data type HVAC mode. Cycle time: max. 35 seconds

This communication object is visible when a heating circuit 2 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Order No. S-0001-006

Product Manual Page 52 (81)

Object
79
Rubric: Function: Description:
Object
80
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 2 ­ “Off” opera- Write tion mode

1 bit

1.011 CRWT-

Data type:

Status

Activates the “Off” operation mode for heating zone 2 or shows whether this is active. Corresponds to “Building Protection” of data type HVAC mode. Cycle time: max. 35 seconds

This communication object is visible when a heating circuit 2 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 2 ­ day temper- Write ature heating

2 bytes

9.001 CRWT-

Data type:

Temperature (oC)

Sets and reads the current setpoint value for the day temperature in heating
zone 2.
multiMATIC cycle time: max. 35 seconds See note on page 43 for sensoCOMFORT Value range: 5-30 °C

This communication object is visible when a heating circuit 2 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Smart control > I would like to be able to configure hot water heating and heating (…) with time control <>

If a value outside the value range is written to this communication object, error code 7 is sent to communication object 12.

Order No. S-0001-006

Product Manual Page 53 (81)

Object
81
Rubric: Function:
Description:
Object
82
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 2 ­ set-back temperature heating

Write

2 bytes

9.001 CRWT-

Data type:

Temperature (oC)

Sets and reads the current setpoint value for the night temperature in heating
zone 2.
multiMATIC cycle time: max. 35 seconds See note on page 43 for sensoCOMFORT Value range: 5-30 °C

This communication object is visible when a heating circuit 2 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Smart control > I would like to be able to configure hot water heating and heating (…) with time control <>

If a value outside the value range is written to this communication object, error code 7 is sent to communication object 12.

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 2 ­ day temper- Write ature cooling

2 bytes

9.001 CRWT-

Data type:

Temperature (oC)

Sets and reads the current setpoint value for the day temperature cooling in heating zone 2. Cycle time: max. 35 seconds Value range: 15-30 °C

This communication object is visible if a Vaillant heat pump and a heating circuit 2 is available, the cooling function is activated in the system controller and
the corresponding use case has been selected.

Parameters > System dimensioning > Heat generator > A Vaillant heat pump is available and Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > System dimensioning > Heating circuit 2 > The cooling function for circuit 2 is activated on the system controller and Parameters > Use cases > Smart control > I would like to be able to configure hot water heating and heating (…) with time control <>

If a value outside the value range is written to this communication object, error code 7 is sent to communication object 12.

Order No. S-0001-006

Product Manual Page 54 (81)

Object
85
Rubric: Function:
Description:
Object
86
Rubric: Function: Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 2 ­ flow tem- Read perature

2 bytes

9.001 CR-T-

Data type:

Temperature (oC)

Displays the current flow temperature in heating circuit 2. Cycle time: max. 3 minutes Value range: 0-99 °C

This communication object is visible when a heating circuit 2 is available and the corresponding use case has been selected.
Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…) <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 2 ­ setpoint flow temperature

Read

2 bytes

9.001 CR-T-

Data type:

Temperature (oC)

Displays the current setpoint flow temperature in heating circuit 2. Cycle time: max. 3 minutes Value range: 0-99 °C

This communication object is visible when a heating circuit 2 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…) <>

Order No. S-0001-006

Product Manual Page 55 (81)

Object
87
Rubric: Function: Description:
Object
88
Rubric: Function: Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 2 ­ pump

Read

1 bit

1.011 CR-T-

Data type:

Status

Displays the operating state of the pump in heating circuit 2. Cycle time: max. 3 minutes

This communication object is visible when a heating circuit 2 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…) <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 2 ­ heating curve

Read

2 bytes

9.031 CR-T-

Data type:

2-byte floating decimal value

Displays the value of the setpoint heating curve parameter. Cycle time: max. 3 minutes Value range: 0.1­4 This communication object is visible when a heating circuit 2 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…) <>

Order No. S-0001-006

Product Manual Page 56 (81)

Object
89
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 2 ­ minimum flow temperature cooling mode

Read

2 bytes

9.001 CR-T-

Data type:

Temperature (oC)

Displays the minimum flow temperature in cooling mode. Cycle time: max. 3 minutes Value range: 7­ 24 °C

The requirement for this is a heating circuit which has the cooling function activated and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 2 > A heating circuit 2 is available for room heating and Parameters > System dimensioning > Heating circuit 2 > The cooling function for circuit 2 is activated on the system controller and Parameters > System dimensioning > Heat generator

A Vaillant heat pump is available and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…)

<>

Order No. S-0001-006

Product Manual Page 57 (81)

Object
90
Rubric: Function:
Description:
Object
91
Rubric: Function: Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 3 ­ operation mode

Write

1 bytes 20.102 CRWT-

Data type:

HVAC mode

Sets and reads the operation mode of heating zone 3. You will find the assignment of KNX operation modes to the system controller in the table on page 43. For communication object 93, the assignment is set to the last “Standby” or “Economy” value sent. Cycle time: max. 35 seconds

This communication object is visible when a heating circuit 3 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 3 ­ “Auto” oper- Write ation mode

1 bit

1.011 CRWT-

Data type:

Status

Activates the “Auto” operation mode for heating zone 3 or shows whether this is active. Corresponds to “Auto” of data type HVAC mode. Cycle time: max. 35 seconds

This communication object is visible when a heating circuit 3 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Order No. S-0001-006

Product Manual Page 58 (81)

Object
92
Rubric: Function: Description:
Object
93
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 3 ­ “Day” oper- Write ation mode

1 bit

1.011 CRWT-

Data type:

Status

Activates the “Day” operation mode for heating zone 3 or shows whether this is active. Corresponds to “Comfort” of data type HVAC mode. Cycle time: max. 35 seconds This communication object is visible when a heating circuit 3 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 3 ­ “Night” op- Write eration mode

1 bit

1.011 CRWT-

Data type:

Status

Activates the “Night” operation mode for heating zone 3 or shows whether this is active. Corresponds to “Economy” or “Standby” of data type HVAC mode. The last value written on communication object 90 is decisive for this state. “Economy” is used as standard. Cycle time: max. 35 seconds

This communication object is visible when a heating circuit 3 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Order No. S-0001-006

Product Manual Page 59 (81)

Object
94
Rubric: Function:
Description:
Object
95
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Heating zone 3 ­ “Off” operation mode Cycle time: max. 35 seconds

Write
Data type:

Data width
1 bit

DP type
1.011

Flags (CRWTU)
CRWT-

Status

Activates the “Off” operation mode for heating zone 3 or shows whether this is active. Corresponds to “Economy” or “Standby” of data type HVAC mode. The last value written on communication object 90 is decisive for this state. “Economy” is used as standard.
This communication object is visible when a heating circuit 3 is available and the corresponding use case has been selected.
Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > Use cases > Smart control > Any use case <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 3 ­ day temper- Write ature heating

2 bytes 9..001 CRWT-

Data type:

Temperature (oC)

Sets and reads the current setpoint value for the day temperature in heating
zone 3.
multiMATIC cycle time: max. 35 seconds See note on page 43 for sensoCOMFORT Value range: 5-30 °C

This communication object is visible when a heating circuit 3 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > Use cases > Smart control > I would like to be able to configure hot water heating and heating (…) with time control <>

If a value outside the value range is written to this communication object, error code 7 is sent to communication object 12.

Order No. S-0001-006

Product Manual Page 60 (81)

Object
96
Rubric: Function:
Description:
Object
97
Rubric: Function:
Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 3 ­ set-back temperature heating

Write

2 bytes

9.001 CRWT-

Data type:

Temperature (oC)

Sets and reads the current setpoint value for the night temperature in heating
zone 3. multiMATIC cycle time: max. 35 seconds See note on page 43 for sensoCOMFORT

Value range: 5-30 °C

Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > Use cases > Smart control > I would like to be able to configure hot water heating and heating (…) with time control <>

If a value outside the value range is written to this communication object, error code 7 is sent to communication object 12.

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating zone 3 ­ day temper- Write ature cooling

2 bytes

9.001 CRWT-

Data type:

Temperature (oC)

Sets and reads the current setpoint value for the day temperature cooling in heating zone 3. Cycle time: max. 35 seconds Value range: 15-30 °C

This communication object is visible if a Vaillant heat pump and a heating circuit 3 is available, the cooling function is activated in the system controller and
the corresponding use case has been selected.

Parameters > System dimensioning > Heat generator > A Vaillant heat pump is available and Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > System dimensioning > Heating circuit 3 > The cooling function for circuit 3 is activated on the system controller and Parameters > Use cases > Smart control > I would like to be able to configure hot water heating and heating (…) with time control <>

If a value outside the value range is written to this communication object, error code 7 is sent to communication object 12.

Order No. S-0001-006

Product Manual Page 61 (81)

ise smart connect KNX Vaillant
Configuration

Object

100

Rubric: Function:

Description:

Object

101

Rubric: Function:

Description:

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 3 ­ flow tem- Read perature

2 bytes

9.001 CR-T-

Data type:

Temperature (oC)

Displays the current flow temperature in heating circuit 3. Cycle time: max. 3 minutes Value range: 0-99 °C

This communication object is visible when a heating circuit 3 is available and the corresponding use case has been selected.
Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…) <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 3 ­ setpoint flow temperature

Read

2 bytes

9.001 CR-T-

Data type:

Temperature (oC)

Displays the current setpoint flow temperature in heating zone 3. Cycle time: max. 3 minutes Value range: 0-99 °C

This communication object is visible when a heating circuit 3 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…) <>

Order No. S-0001-006

Product Manual Page 62 (81)

Object

102

Rubric: Function:

Description:

Object

103

Rubric: Function:

Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 3 ­ pump

Read

1 bit

1.011 CR-T-

Data type:

Status

Displays the operating state of the pump in heating circuit 3. Cycle time: max. 3 minutes

This communication object is visible when a heating circuit 3 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…) <>

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 3 ­ heating curve

Read

2 bytes

9.031 CR-T-

Data type:

2-byte floating decimal value

Displays the value of the setpoint heating curve parameter. Cycle time: max. 3 minutes Value range: 0.1-4 This communication object is visible when a heating circuit 3 is available and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…) <>

Order No. S-0001-006

Product Manual Page 63 (81)

Object

104

Rubric: Function:

Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heating circuit 3 ­ minimum flow temperature cooling mode

Read

2 bytes

9.001 CR-T-

Data type:

Temperature (oC)

Displays the minimum flow temperature in cooling mode. Cycle time: max. 3 minutes Value range: 7-24 °C

The requirement for this is a heating circuit which has the cooling function activated and the corresponding use case has been selected.

Parameters > System dimensioning > Heating circuit 3 > A heating circuit 3 is available for room heating and Parameters > System dimensioning > Heating circuit 3 > The cooling function for circuit 3 is activated on the system controller and Parameters > System dimensioning > Heat generator

A Vaillant heat pump is available and Parameters > Use cases > Information > I would like to see the system status of my Vaillant system (…)

<>

Order No. S-0001-006

Product Manual Page 64 (81)

Object

201

Rubric: Function:

Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heat generator ­ flow temper- Read ature

2 bytes

9.001 CR-T-

Data type:

Temperature (oC)

Displays the heat generator’s current flow temperature. Cycle time: max. 3 minutes Value range: 0-120 °C

The minimum requirement for this is the installation of a Vaillant gas boiler and/or a Vaillant heat pump and selection of the corresponding use case.

Parameters > System dimensioning > Heat generator > A Vaillant gas boiler is available and/or Parameters > System dimensioning > Heat generator > A Vaillant heat pump is available

You can configure up to eight heat generators. Each analogue communication object has an offset of 5. Example: Heat generator 1 has the communication object number 201 Heat generator 2 has the communication object number 206

Order No. S-0001-006

Product Manual Page 65 (81)

Object
Rubric: Function:

202

Description:

ise smart connect KNX Vaillant
Configuration

Name

Direction

Data width

DP type

Flags (CRWTU)

Heat generator ­ error

Read

1 bit

1.002 CR-T-

Data type:

Boolean

Shows whether the heat generator has an error. Cycle time: max. 5.5 minutes True = Error exists

The minimum requirement for this is the installation of a Vaillant gas boiler and/or a Vaillant heat pump and selection of the corresponding use case.

Parameters > System dimensioning > Heat generator > A Vaillant gas boiler is available and/or Parameters > System dimensioning > Heat generator > A Vaillant heat pump is available

You can configure up to eight heat generators. Each analogue communication object has an offset of 5. Example: Heat generator 1 has the communication object number 202 Heat generator 2 has the communication object number 207

Order No. S-0001-006

Product Manual Page 66 (81)

4 Commissioning 4.1 Operation

ise smart connect KNX Vaillant
Commissioning

Figure 9: ise smart connect KNX Vaillant.

1

Programming button for KNX

Switches the device to the ETS programming mode or vice versa.

2

KNX connection (twisted Left: ( + / red)

pair)

Right: ( – / black)

3

Connection for power supply

DC 24 to 30 V, 2 W (at 24 V) Left: ( + / yellow) Right: ( – / white)

4

KNX programming LED (red)

Red: Device is in ETS programming mode Yellow: See 4.2.1 / 4.2.2 for start or diagnosis code

5 LED APP (green)

Green: Normal operation
Off / flashes: See 4.2.1 / 4.2.2 for start or diagnosis code

6 LED COM (yellow) 7 Ethernet connection

Yellow: Normal operation (brief dark phases indicate KNX telegram traffic)
Off /
flashes: See 4.2.1 / 4.2.2 for start or diagnosis code

LED 10/100 speed

(green)

On: 100 Mbit/s

Off:

10 Mbit/s

LED link/ACT (orange)

On:

Connection to IP network

Off:

No connection

Flashes: Data reception on IP

8 USB connection 9 microSD card slot

USB connection type A establishes the connection to the system controller via the ise eBUS Adapter. Use the supplied USB cable as standard. Please note that the use of USB cables with a length of more than 3 m is generally not permitted.
Without function.

Order No. S-0001-006

Product Manual Page 67 (81)

ise smart connect KNX Vaillant
Commissioning
4.2 LED status displays
The device features three status LEDs on the upper housing side and two status LEDs at the network connections. The LED displays have different meanings
· while the device is starting and · during operation.
4.2.1 LED status display upon device start-up
After the power supply (DC 24 V on the yellow-white connection terminal) is switched on or after a return in voltage occurs, the device indicates its status through the following LED combinations:

“APP” LED (green)

LED “COM” (yellow)

Meaning

Off

Off

No power supply ­ Check connections and power supply.

Off

Yellow Device starting up.

Green

Off

Error ­ KNX not connected.

…… Green Flash slowly

Yellow

The application has not been configured yet, e.g. not yet loaded with the ETS.

Green

Yellow

Device booted up and ready for operation.

…… Green Flash quickly

Off

Error ­ Please contact support. The firmware cannot be started.

…………… Green

Error ­ Please contact support.

…………… Yellow Flash slowly in an

The newly loaded firmware cannot be started. The system is trying to activate

alternating fashion

the previous firmware (invalid firmware).

Order No. S-0001-006

Product Manual Page 68 (81)

ise smart connect KNX Vaillant
Commissioning
4.2.2 LED status display in operation
Once device start-up is complete, the meaning of the LEDs is as follows:

LED “APP” (green)

Meaning

Green

Normal operation

Off

Device in start-up procedure or out of operation: Wait until the start-up for procedure is complete or check the power supply

…… Flashes at approx. 1 Hz

Error:
Application is not parametrised or not fully parametrised. Check the device parametrisation in the ETS and carry out an application download to the device.

……………
Three slow flashes followed by a 2 sec pause

KNX Gateway error:
3 = Error in communication with the ise eBUS Adapter. Communication between the ise smart connect KNX Vaillant and the ise eBUS Adapter is not possible via USB.
4 = eBUS cable not connected. eBUS connection not recognised.

……………… ………
Five slow flashes followed by a 2 sec pause

KNX Gateway error:
1 = system controller not found. eBUS communication is possible, but no system controller was found.

LED “COM” (yellow) Yellow
Yellow with brief dark phases

Meaning
Normal operation: KNX connection is established; no KNX telegram traffic.
Normal operation: KNX connection is established; KNX telegram traffic.

Error:

Off

Connection to KNX is interrupted.

Check the bus connection.

Order No. S-0001-006

Product Manual Page 69 (81)

ise smart connect KNX Vaillant
Commissioning
4.3 Accelerate transfer: Select transfer path KNX-TP or IP
Downloading (transmission from the ETS to the device) occurs in the programming environment of the ETS. An additional KNX data interface is not required for transfer (bus connection via bus connection terminal). The ETS can reach the device from both the IP page and the KNX TP page.
Due to considerably shorter transmission times, we recommend downloading from the device’s IP page.

Figure 10: The “Use direct KNX-IP connection if available” setting accelerates transmission from the ETS to the device.
To transmit the ETS via the IP side, configure the setting
Use direct KNX-IP connection if available.
on the ETS start page Bus tab Options entry.
4.4 Downloading the individual address of the device
· Ensure that the device and bus voltage are switched on. · Ensure that the programming LED (4) is not illuminated. · Press programming button (1) briefly – Programming LED (4) lights up red. · Download individual address using the ETS.
After a successful programming procedure, · LED (4) will go out. · The ETS shows the completed transfer with a green marking under History in the sidebar (nor-
mally at the right edge of the window). · The ETS sets the commissioning tick on the device for “Adr” and “Cfg”.
You can now note down the individual address on the device.

Order No. S-0001-006

Product Manual Page 70 (81)

ise smart connect KNX Vaillant
Commissioning
4.5 Transferring application programs and configuration data
After programming the individual address, the application program, parameter settings and group address connections can be transferred to the device.
A connection to the device can be further established via IP or KNX for this purpose. · Select “Download > Download application” to do so. The download lasts around 10 seconds with a direct IP connection or about 35 seconds if using TP. · After the download, please wait approx. 15 seconds while the device copies the data and installs the application. · Commissioning is complete.
4.6 Factory reset
The following individual KNX address is pre-set in the factory: 15.15.255 Following the factory reset, the device behaves as in the state of delivery. The device is unconfigured. This is indicated by the slowly flashing green APP LED (5) after the device is started up.
4.6.1 Factory reset using the programming button on the device
The device can be reset to the factory settings through a sequence during start-up. · Make sure that the device is switched off. · Press and hold programming button (1) and switch on the device. · Press and hold programming button (1) until the programming LED (4), the APP LED (5) and the COM LED (6) flash slowly simultaneously. · Briefly release the programming button (1), then press and hold it again until the programming LED (4), the APP LED (5) and the COM LED (6) flash quickly simultaneously. · The factory reset is being carried out; release programming button. · The device need not be restarted following a factory reset.
The factory reset can be cancelled at any time by interrupting the sequence.
4.6.2 Factory reset using the website of the device
The factory reset can also be triggered from the website of the device.
· Call up the website of the device. For this purpose, double-click the icon of the device in the Other Devices area in the network environment.

· Alternatively, you can also enter the IP address of the device in your browser. · Select Device status in the upper menu bar on the website. · Select System > Factory reset in the upper menu bar on the status page. · Confirm the factory reset when the security prompt appears. · The next displayed page Factory reset shows that the factory reset is being carried out. As soon
as this is complete, the start page is loaded again.

Order No. S-0001-006

Product Manual Page 71 (81)

ise smart connect KNX Vaillant
Commissioning
4.7 Firmware update of the device
4.7.1 Firmware update using the device website
The ise smart connect KNX Vaillant makes it possible to install firmware updates using the device website. Select the Firmware update menu item under System on the device website to do so. The ise smart connect KNX Vaillant will now automatically search the update server for a newer version and show the current firmware version and the versions of any available updates. If a newer version is available, the associated description of the version is also displayed.
If the new firmware is incompatible with the configuration of the previous firmware, a corresponding message is displayed. A differentiation is made between the following cases here:
1. The new version provides new functionality. After the update, the device functions with the same range of functions as before. New functions cannot be used until an ETS download of a newer catalogue entry occurs.
2. The new version is completely incompatible with parametrisation in the version currently being used. An ETS download is absolutely necessary. We recommend unloading the ETS application program before the update and configuring the device with a new catalogue entry after the update.
The update can be started using the Perform update button. Should an incompatibility arise, the update must be confirmed again for security purposes.
4.7.2 Local firmware update without internet access
In addition to online updates, it is possible to carry out local updates without an internet connection. This is intended for devices which do not have an internet connection at their installation site and are only accessible via the local network. The firmware file can be selected locally using the Choose File button and then started using the Perform update button. In this case, the user is responsible for ensuring that the update is compatible (see chapter 4.7.3 “Compatibility of catalogue entry with firmware”). A downgrade to an older version is not possible.
4.7.3 Compatibility of catalogue entry with firmware
The version numbers in the catalogue entry and the firmware use an X.Y format. The main number, X, of the respective version indicates whether the catalogue entry and firmware are compatible. This is the case if both main numbers are identical. The second part of the version number, Y, is not relevant for compatibility. It simply indicates updates within the version.
If new firmware has a higher main number, it cannot be guaranteed that this version is compatible with an old ETS catalogue entry. For this reason, we recommend always unloading the application program from the device before the update and to then only use the new catalogue entry after that.
If the main numbers are the same, it may be necessary to use a new ETS catalogue entry for full functionality. However, this is not absolutely necessary if the new functions are not used in your project.

Order No. S-0001-006

Product Manual Page 72 (81)

ise smart connect KNX Vaillant
Technical data

5 Technical data

5.1 ise smart connect KNX Vaillant

KNX medium Commissioning mode KNX supply KNX connection

TP S-Mode (ETS) DC 21 to 30 V SELV
Bus connection terminal

External supply Voltage Connection Power consumption

DC 24…30 V ±10%
Bus connection terminal, preferably yellow (+)/white (­) typ. 1.2 W (with DC 24 V and connected ise eBUS Adapter) The device must be supplied with voltage by a dedicated power supply unit. Do not use the auxiliary voltage output of a KNX power supply unit which is also supplying a KNX line.

IP communication IP connection USB connection
Supported protocols
microSD card Ambient temperature Storage temperature Installation width Installation height Installation depth

Ethernet 10/100 BaseT (10/100 Mbit/s) 1 x RJ45 1 x USB type A Use the supplied USB cable as standard. Please note that the use of USB cables with a length of more than 3 m is generally not permitted. ARP, ICMP, IGMP, UDP/IP, DHCP, AutoIP KNXnet/IP as per KNX system specifications: Core, Device Management Without function 0 °C to +45 °C -25 °C to +70 °C 36 mm (2 HP) 90 mm 74 mm

Protection type Protection class

IP20 (compliant with EN60529) III (compliant with IEC 61140)

Test marks

KNX, CE

Order No. S-0001-006

Product Manual Page 73 (81)

5.2 ise eBUS Adapter
Operating voltage eBUS connection USB connection eBUS power consumption: USB power consumption:
Ambient temperature Storage temperature Installation width Installation height Installation depth
Test marks

Supply via eBUS Connection terminal 1 x mini USB B 0.1 W at 24 V 0.05 W
0 °C to +45 °C -25 °C to +70 °C 17.5 mm (1 HP) 90 mm 58 mm
CE

ise smart connect KNX Vaillant
Technical data

Order No. S-0001-006

Product Manual Page 74 (81)

ise smart connect KNX Vaillant
Frequently asked questions (FAQ)
6 Frequently asked questions (FAQ)
· How can I find my ise smart connect KNX Vaillant’s IP address? Please read about this in chapter 4.6.2 “Factory reset using the website of the device”.
· Are there software updates for my ise smart connect KNX Vaillant device? Please read about this in chapter 4.7 “Firmware update of the device”. Please also visit www.ise.de/en/home for more information.
· Why does the ETS report the error that it is not possible to write on a protected area when downloading the application program? Please ensure that your ETS version is up to date. The ise smart connect KNX Vaillant requires the current version of the ETS5.
· Why is my ise smart connect KNX Vaillant restarting? After connecting the ise smart connect KNX Vaillant with the ise eBUS adapter, a restart may be necessary to initialise the eBUS connection.
· What do I need to bear in mind if I replace the multiMATIC system controller with a sensoCOMFORT? The setpoint value must be written on the data point of the communication objects Day temperature heating (CO 65/80/95) or Set-back temperature heating (CO 66/81/96) to ensure that the heating uses the required setpoint value after the system controller is replaced.

Order No. S-0001-006

Product Manual Page 75 (81)

ise smart connect KNX Vaillant
Troubleshooting and support
7 Troubleshooting and support
If you have a problem with your ise smart connect KNX Vaillant and require support, please send an email with a detailed error description and the log file created after the error occurred to support@ise.de. Refer to Chapter 7.1 “Downloading log files if a problem occurs” for information on how to download the log files from your ise smart connect KNX Vaillant.
7.1 Downloading log files if a problem occurs
If a problem occurs, the log files are required for providing support. They can be downloaded via the website of the device (see chapter 4.6.2 “Factory reset using the website of the device”). To do so, proceed as follows:
· Call up the website of the device. For this purpose, double-click the icon of the device in the Other Devices area in the network environment.
· Select System in the upper menu bar on the website. · Select Download logfile. · The page which opens starts downloading the log files. If this does not occur, the provided link
can be used.
7.2 Status page of the ise smart connect KNX Vaillant
You can call up the device status on the website of the ise smart connect KNX Vaillant (see chapter 4.6.2 “Factory reset using the website of the device”). Among other things, it displays the installed software version and the configuration and connection status in the ise smart connect KNX Vaillant. Should an error occur, please send us a screenshot of the status page.

Order No. S-0001-006

Product Manual Page 76 (81)

ise smart connect KNX Vaillant
Troubleshooting and support
7.3 The ise smart connect KNX Vaillant does not work
The following error tree is intended to solve the most common problems. Should this be unsuccessful, please contact us at support@ise.de.
?

Are the LEDs not light-

ing up or do they flash

YES

individually in an alter-

nating fashion?

N O

Please check the cabling as specified in Chapter 2.5 and the LED status displays as specified
in Chapter 4.2.1.
O K

Does the APP LED flash slowly?

YES

Please check device para-
metrisation in the ETS as specified in Chapter 3.

N O

Does the APP LED flash

three times with a two-

YES

second pause each time?

N O

Does the APP LED flash

five times, each with a

YES

two-second pause?

Check device parametrisation in the ise eBUS
adapter connections as specified in Chapter 2.5 and check the KNX Gateway error as specified in
Chapter 4.2.2.
Please check device parametrisation in the communication with the eBUS as
specified in Chapter 2.5 and check the KNX Gateway error as specified in
Chapter 4.2.2.

Is the device not visible

on the network?

YES

N O

Check the network cabling and parametrisation of the device IP in the ETS as specified in
Chapter 3.3.

If neither the approaches above nor Chapter 6 provide a solution, please load the log files from the device, if possible, and send them together with a description of the error with as many details as possible
to support@ise.de.

Order No. S-0001-006

Product Manual Page 77 (81)

ise smart connect KNX Vaillant
ise smart connect KNX Vaillant software licence agreement
8 ise smart connect KNX Vaillant software licence agreement
Hereinafter are the contract terms for your use of the software as the “Licensee”. On accepting this agreement and installing the ise smart connect KNX Vaillant software or putting the ise smart connect KNX Vaillant into use, you conclude an agreement with ise Individuelle Software und Elektronik GmbH and agree to abide by the terms in this agreement.
8.1 Definitions
Licensor: ise Individuelle Software und Elektronik GmbH in Oldenburg, Osterstraße 15, Germany Licensee: The legal recipient of the ise smart connect KNX Vaillant software. Firmware: Software which is embedded on the ise smart connect KNX Vaillant hardware and enables operation of the ise smart connect KNX Vaillant. ise smart connect KNX Vaillant software: The ise smart connect KNX Vaillant software designates all of the software provided for the ise smart connect KNX Vaillant product, including the operating data. This includes, in particular, the firmware and the product database.
8.2 Object of the agreement
The object of this agreement is the ise smart connect KNX Vaillant software provided on data media or through downloads, as well as the corresponding documentation in written and electronic form.
8.3 Rights of use of the ise smart connect KNX Vaillant software
The licensor grants the licensee the non-exclusive, non-transferable right to use the ise smart connect KNX Vaillant software for an unlimited time in accordance with the following conditions for the purposes and applications specified in the valid version of the documentation (which shall be provided in printed format or also as online help or online documentation). The licensee is obliged to ensure that each person who uses the program only does so as part of this license agreement and observes this license agreement.
8.4 Restriction of rights of use
8.4.1 Copying, modification and transmission
The Licensee is not authorised to use, copy, modify or transfer the ise smart connect KNX Vaillant software in whole or in part in any way other than as described herein. Excluded from this is one (1) copy produced by the Licensee exclusively for archiving and backup purposes.
8.4.2 Reverse engineering and conversion technologies
The licensee is not authorised to apply reverse-engineering techniques to the ise smart connect KNX Vaillant software or to convert the ise smart connect KNX Vaillant software into another format. Such techniques include, in particular, disassembly (conversion of the binary-coded computer instructions of an executable program into an assembler language which can be read by humans) or decompilation (conversion of binary-coded computer instructions or assembler instructions into source code in the form of high-level language instructions).

Order No. S-0001-006

Product Manual Page 78 (81)

ise smart connect KNX Vaillant
ise smart connect KNX Vaillant software licence agreement
8.4.3 Firmware and hardware
The firmware may only be installed and used on the hardware (ise smart connect KNX Vaillant) approved by the Licensor.
8.4.4 Transfer to a third party
The ise smart connect KNX Vaillant software may not be passed on to third parties, nor may it be made accessible to third parties.
8.4.5 Renting out, leasing out and sub-licensing
The Licensee is not authorised to rent or lease the ise smart connect KNX Vaillant software or grant sub-licenses to the program.
8.4.6 Software creation
The Licensee requires written approval from the Licensor to create and distribute software which is derived from the ise smart connect KNX Vaillant software.
8.4.7 The mechanisms of license management and copy protection
The mechanisms of the license management and copying protection of the ise smart connect KNX Vaillant software may not be analysed, published, circumvented or disabled.
8.5 Ownership, confidentiality
8.5.1 Documentation
The ise smart connect KNX Vaillant software and its documentation (which shall be provided in printed format or also as online help or online documentation) are business secrets of the licensor and/or the object of copyright and/or other rights and shall continue to belong to the licensor. The Licensee shall observe these rights.
8.5.2 Transfer to a third party
Neither the software, the data backup copy nor the documentation (which shall be provided in printed format or also as online help or online documentation) may be passed on to third parties at any point in time, in whole or in part, for a fee or free of charge.
8.6 Changes, additional deliveries
The ise smart connect KNX Vaillant software and the documentation (which shall be provided in printed form or additionally as online help or online documentation) shall be subject to possible changes by the licensor.
8.7 Warranty
The ise smart connect KNX Vaillant software shall be delivered together with software from third parties as listed in chapter “9 ­ Open Source Software”. No warranty is provided for software from third parties.

Order No. S-0001-006

Product Manual Page 79 (81)

ise smart connect KNX Vaillant
ise smart connect KNX Vaillant software licence agreement
8.7.1 Software and documentation
The ise smart connect KNX Vaillant software and the documentation (which shall be provided in printed form or additionally as online help or online documentation) shall be provided to the licensee in the respective valid version. The warranty period for the ise smart connect KNX Vaillant software is 24 months. The licensor shall provide the following warranty during this time:
· The software shall be free of material and manufacturing defects when turned over to the customer.
· The software shall function in accordance with the documentation included with it in the respective valid version.
· The software shall be executable on the computer stations specified by the Licensor.
The warranty shall be fulfilled with the supply of spare parts.
8.7.2 Limitation of warranty
No warranty shall be provided for the freedom from errors for the ise smart connect KNX Vaillant software and its data structures. Nor does the warranty cover defects due to improper use or other causes outside the influence of the licensor. Any additional warranty claims shall be excluded.
8.8 Liability
The Licensor shall not be liable for damages due to loss of profit, data loss or any other financial loss resulting from use of the ise smart connect KNX Vaillant software, even if the Licensor is aware of the possibility of such damage. This limitation of liability is valid for all the Licensee’s damage claims, regardless of the legal basis. In any case, liability is limited to the purchase price of the product. The exclusion of liability does not apply to damage caused with intent or through gross negligence on the part of the licensor. Furthermore, claims based on the statutory regulations for product liability shall remain intact.
8.9 Applicable law
This agreement is subject to the laws of the Federal Republic of Germany. The place of jurisdiction is Oldenburg.
8.10 Termination
This agreement and the rights granted herein shall end if the licensee fails to fulfil one or more provisions of this agreement or terminates this agreement in writing. The supplied ise smart connect KNX Vaillant software and the documentation (which is provided in printed form or also as online help or online documentation), including all copies, shall be returned immediately in such a case without the Licensor specifically requesting their return. No claim to reimbursement of the price paid shall be accepted in such a case. The license to use the ise smart connect KNX Vaillant software shall expire upon termination of the agreement. The ise smart connect KNX Vaillant product must be taken out of operation in such a case. Further use of the ise smart connect KNX Vaillant without a license is precluded. The commissioning and visualisation software must be uninstalled and all copies must be destroyed or returned to the licensor.

Order No. S-0001-006

Product Manual Page 80 (81)

ise smart connect KNX Vaillant
ise smart connect KNX Vaillant software licence agreement
8.11 Subsidiary agreements and changes to the agreement
Subsidiary agreemen

References

• ise Individuelle Software und Elektronik GmbH
• KNX For Professionals – KNX Association [Official website]

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>