behringer 130 Legendary Analog Dual VCA Module for Eurorack User Guide
- July 9, 2024
- Behringer
Table of Contents
behringer 130 Legendary Analog Dual VCA Module for Eurorack
FAQ
- Q: Where can I find the warranty information for the 130 DUAL VCA?
- A: For the applicable warranty terms and conditions and additional details regarding Music Tribe’s Limited Warranty, please visit community.musictribe.com/support.
Safety Instruction
- Please read and follow all instructions.
- Keep the apparatus away from water, except for outdoor products.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
- Use only attachments/accessories specified by the manufacturer.
- Use only specified carts, stands, tripods, brackets, or tables. Use caution to prevent tip-over when moving the cart/apparatus combination.
- Avoid installing in confined spaces like bookcases.
- Do not place near naked flame sources, such as lighted candles.
- Operating temperature range 5° to 45°C (41° to 113°F).
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice.
All trademarks are the property of their respective owners. Midas, Klark
Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon,
Behringer, Bugera, Aston Microphones and Coolaudio are trademarks or
registered trademarks of Music Tribe Global Brands Ltd.
© Music Tribe Global Brands Ltd. 2024 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at community.musictribe.com/support.
130 DUAL VCA Controls
Controls
- SIG IN input jacks accept audio signals over cables with 3.5 mm TS connectors.
- SIG IN knobs control the gain level at the SIG IN inputs.
- VCA OUT (HIGH/LOW) outputs connect to the inputs of external equipment over cables with 3.5 mm TRS connectors. (Note thatthese connections are both mono and not left/right). The HIGH mono output can be connected to the line-level inputs of mixers, keyboard amplifiers or powered speakers. The LOW output is an instrument-level signal that can be connected to the HI-Z inputs of equipment such as guitar amplifiers or mixers.
- LINEAR/EXPONENTIAL switch toggles between linear and exponential output modes.
- INITIAL GAIN knob controls the gain level at the VCA OUT jacks.
- MOD IN knobs control the amount of carrier signal allowed through from the MOD IN jacks.
- MOD IN jacks accept carrier signals from other modules (e.g., a sine wave at 500 Hz) to shape the volume envelopes and waveforms of the SIG IN signals. For these jacks, use cables with 3.5 mm TS connectors.
Connection And Installation
Power Connection
The 130 DUAL VCA comes with the required power cable for connecting to a standard Eurorack power supply system. Follow these steps to connect power to the module. It is easier to make these connections before the module has been mounted into a rack case.
- Turn the power supply or rack case power off and disconnect the power cable.
- Insert the 16-pin connector on the power cable into the socket on the power supply or rack case. The connector has a tab that will align with the gap in the socket, so it cannot be inserted incorrectly. If the power supply does not have a keyed socket, be sure to orient pin 1 (-12 V) with the red stripe on the cable.
- Insert the 10-pin connector into the socket on the back of the module. The connector has a tab that will align with the socket for correct orientation.
- After both ends of the power cable have been securely attached, you may mount the module in a case and turn on the power supply.
Installation
- The necessary screws are included with the module for mounting in a Eurorack case. Connect the power cable before mounting.
- Depending on the rack case, there may be a series of fixed holes spaced 2 HP apart along the length of the case, or a track that allows individual threaded plates to slide along the length of the case.
- The free-moving threaded plates allow precise positioning of the module, but each plate should be positioned in approximate relation to the mounting holes in your module before attaching the screws.
- Hold the module against the Eurorack rails so that each of the mounting holes are aligned with a threaded rail or threaded plate.
- Attach the screws part way to start, which will allow small adjustments to the positioning while you get them all aligned. After the final position has been established, tighten the screws down.
Specifications
Signal Connections
| Signal in | 6 x 3.5 mm jack, summed |
|---|---|
| Impedance | > 50 kΩ unbalanced |
| Maximum input level | +18 dBu @ unity gain |
| VCA out high / low | 4 x 3.5 mm jack |
| High output Impedance | 1 kΩ unbalanced |
| Low output Impedance | 3 kΩ unbalanced |
| High maximum output level | +18 dBu |
| Low maximum output level | -2 dBu |
| High output noise | < -66 dBu, 22 Hz – 22 kHz |
| Low output noise | < -86 dBu, 22 Hz – 22 kHz |
| Mod in | 6 x 3.5 mm jack |
| Impedance | > 50 kΩ unbalanced |
| CV input range | 0 V to +10 V |
| CV scaling in EXP mode | Typically 1 V/10 dB |
Controls
Initial gain
| 2 x rotary knob Linear / exponential, switchable
---|---
Sig in level| 6 x rotary knob
Mod in level| 6 x rotary knob
Linear / exponential CV| 2 x sliding switch
Power
| Power supply | Eurorack |
|---|---|
| Current draw | 30 mA (+12 V), 20 mA (-12 V) |
Physical
Dimensions (H x W x D)| 44 x 81 x 129 mm
(1.7 x 3.2 x 5.1″)
---|---
Rack units| 16 HP
Weight| 0.18 kg (0.4 lbs)
FCC STATEMENT
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
- Behringer: 130 DUAL VCA
- Responsible Party Name: Music Tribe Commercial NV Inc.
- Address: 122 E. 42nd St.1, 8th Floor NY, NY 10168, United States
- Email Address: legal@musictribe.com
130 DUAL VCA
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference.
- this device must accept any interference received, including interference that may cause undesired operation.
Important information:
- Changes or modifications to the equipment not expressly approved by Music Tribe can void the user’s authority to use the equipment.
CE: Hereby, Music Tribe declares that this product is in compliance with
Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU,
Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive
1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Gammel Strand 44, DK-1202 København K, Denmark
UK Representative: Music Tribe Brands UK Ltd.
Address: 8th Floor, 20 Farringdon Street London EC4A 4AB, United Kingdom
Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed for the recycling of waste electrical and electronic equipment (EEE). The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the efficient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city office, or your household waste collection service.
Made in China
CAN ICES–003 (B)/NMB–003 (B)
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>