TORIN 5 Piece Garage Cabinet Set Owner’s Manual
- June 25, 2024
- Torin
Table of Contents
GARAGE
CABINET SERIES
OWNER’S
MANUAL
INSTRUCTIONS FOR USE
5 Piece Garage Cabinet Set
Important
When you open the cartons, carefully check the contents and make sure there is
no damage. If you have any problems or you find any parts damaged or missing,
Please contact with us first.
Do not return the product to the store before contacting us. Do not dispose of
your cartons until you are completely satisfied with your products.
To reduce the risk of injury, the user should read and understand this owner’s
manual before assembling and using these products for the first time.
Fill in the following information and retain this manual for future reference:
Item No. ___
Date of Purchase _
Place of Purchase
Receipt No. ____
Safety Guidelines
- WARNING Use two or more people to move, assemble, and install the product to avoid any injury.
- WARNING DO NOT leave children unattended near the product.
- WARNING DO NOT stand on the product or lean on the drawers or worktop.
- WARNING WEAR SAFETY GLASSES when removing or repositioning the slides. The tools could slip, which may cause personal injury.
- WARNING DO NOT alter the product in any manner. For example, do not weld external lock bars or attach unapproved electrical equipment. This may cause product damage, personal injury, or death.
- WARNING DO NOT OVERLOAD PRODUCTS!
The components of the product are designed to carry the following maximum weight capacities: Cabinet| Shelf Weight Capacity (Ibs.)| Drawer Weight Capacity (Ibs.)| Bottom Weight Capacity (Ibs.)| Top Weight Capacity (Ibs.)| Overall Weight Capacity (Ibs.)
---|---|---|---|---|---
Locker| 150| /| 220| 150| 820
Wall Cabinet| /| /| 100| /| 100
2-Door Base Cabinet| 150| /| 150| 220| 520
4-Drawer-Cabinet| /| 100×4| /| 220| 620
1-Drawer-Cabinet| 150| 100×1| 150| 220| 620 - CAUTION BE CAREFUL when opening more than one drawer. The product could become unstable and tip, which may cause product damage or personal injury.
- CAUTION High risk of tipping if the product is not installed correctly. Securely attach the product to the wall to avoid serious injury.
Unpacking
- Start by placing the package on flat covered ground.
- Remove all cardboard, honey comb board, foam packaging material and clear plastic bags.
- Recycle all packaging materials.
- Verify all the contents are included and gather the tools required.
Hardware Included
No.| DESCRIPTION| QTY. FOR WALL CABINET| QTY. FOR BASE
CABINET| QTY. FOR LOCKER| QTY.FOR 4-DRAWER CABINET|
QTY.FOR 1-DRAWER CABINET
---|---|---|---|---|---|---
1| M6 Hex Flange Nut| 4| 4| 4| 4| 4
2| Flat Washer| 4| 2| 4| 2| 2
3| Key| 2| 2| 2| 2| 2
4| M5 x 50 Hex Tapping Bolt| 4| 2| 4| 2| 2
5| M6 x 12 Flat-Head Bolt| 4| 24| 20| 24| 24
6| M5 x 12 Flat-Head Bolt (on the door)| 4| 4| 4| 8| 6
7| Adjustable Leveling Feet| 0| 4| 4| 4| 4
8| Shelf| 0| 1| 3| 0| 1
Tools Required
4-Drawer Cabinet
2-Door Base Cabinet
1-Drawer 2-Door Cabinet
Wall Cabinet
Locker
Installing the Handles
Unscrew the bolts on the front of the drawers or the doors using a Phillips screw driver to remove the handle on the back of it, then attach the handle to the front of the door or the drawer using two M5x12 flat head bolts. Repeat for all the doors and drawers.
Installing the Feet
Carefully set the locker / 2-door base cabinet / 1-drawer 2-door cabinet on
its back or then attach the adjustable leveling feet to the locker or the
cabinet using sixteen M6x12 flat-head bolts with a Philips screw
driver.
Installing the Shelves
Check the location need, carefully put the shelf into the slot.
Please make sure the shelf is stable.
NOTE: A center shelf must be installed level with the lock on the cabinet
door in order for lock to work.
Installing the Worktop
Open the doors or remove the drawers to make sure that you have enough space
to install the worktop.
Carefully place the wood worktop on the
cabinets and fasten it with cordless power drill and four screws in the parts
package of each base cabinet / drawer cabinet. 
Setup
-
Planning the position of the cabinets
A. Use a tape measure to measure and record the height and width of each cabinet.
B. Determine how high off the ground you would like the cabinets to be (80mm- 105mm) and make a horizontal mark at that position.
C. Mark the width of each cabinet recorded in step A at the intended position, to ensure that the wall cabinets will align properly.
D. Measure up from the line marked in step B and make a horizontal mark at each cabinet’s height as recorded in step A, to determine where the top of the cabinets will be.
E. Make sure that the cabinets will be at a suitable height and the wall cabinets are not out of reach.
Note: Make sure that there are two studs to mount the
locker on as it is easiest to start the installation with the locker first.
Due to the spacing of the wall studs, some wall cabinets maybe have only one
stud to attach to; this is acceptable if the wall cabinets are bolted
together. -
Hanging the lockers and wall cabinets on wall
Open the doors and align the top of the locker with the lines marked for the position of the top of the cabinets and securely attach locker into the studs using four M5x50 hex tapping bolts and four flat washers.
Repeat
for the other locker and wall cabinets. -
Connecting the cabinets and lockers together
For the cabinet set, open all the doors and remove the top drawer. Push the base/wall cabinet and locker together. Insert M6x12 flat-head bolts through the two interior holes and secure them together with M6 Hex flange nuts using a Phillips screw driver and wrench.
Repeat for the other locker and cabinets.
Tighten all the bolts to fasten the cabinets and level the cabinets.
The installation of the garage cabinet set is finished.
Operation
Drawer Removal
Pull the drawer out so that it’s almost fully extended. Push up on the black
release lever on one side, while pulling down on the black release lever on
the other side. While holding the levers in the positions as illustrated
below, pull the drawer outward until it is released from the drawer
slide.
Drawer
Replacement
Extend the drawer slides from the cabinet. Insert the brackets on each side of
the drawer into the slots in the slides, being careful to position them
properly. Once inserted, close the drawer completely to set the slides in
their proper positions.
Maintenance
- Lubricate the slides twice a year with a quality lubricant. This is especially necessary when the temperature drops, which may cause the bearings to be stiff.
- Periodically clean the drawer fronts, doors, handles and other surfaces with mild and water.
- For safety, use a non-flammable cleaning fluid. Grease and oil can be removed with most standard cleaning fluids.
Distributed by: TORIN INC.
Ontario, CA 91761
FOR CUSTOMER SERVICE
PARA SERVICION AL CLIENTE
www.torin-usa.com/support
Made in China
www.torin-usa.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>