TEGERA 8804R Infinity Nitrile Coated Contact Heat Resistant Gloves Instructions
- June 3, 2024
- TEGERA
Table of Contents
TEGERA 8804R Infinity Nitrile Coated Contact Heat Resistant Gloves
Instructions
INSTRUCTIONS FOR USE
Carefully read these instructions before using this product.
EXPLANATION OF PICTOGRAMS 0 = Below the minimum performance level for the given individual hazard X= Not submitted to the test or test method not suitable for the glove design or material
Warning! This product is designed to provide protection specified in PPE Regulation (EU) 2016/425 with the detailed levels of performance presented below. However, always remember that no item of PPE can provide full protection and caution must always be taken when exposed to risks.
EN 407:2004 PROTECTIVE GLOVES AGAINST THERMAL RISKS (HEAT AND/OR FIRE)
- A: Burning behaviour
- B: Contact heat
- C: Convective heat
- D: Radiant heat
- E: Small splashes of molten metal
- F: Large quantities of molten metal
PERFORMANCE (A-F)
Min. 0; Max. 4
Warning: EN 407:2004: if the glove consists of seperate parts which are not permanently interconnected, the perfomance levels and the protection only apply to the complete assembly. If the gloves have a performance level 1, 2 or X in burning behaviour in EN 407:2004 the gloves should not come in contact with naked flame.
EN 388:2016
A. Abrasion resistance Min. 0; Max. 4
B. Blade cut resistance Min. 0; Max. 5
C. Tear resistance Min. 0; Max. 4
D. Puncture resistance Min. 0; Max. 4
E. Cut Resistance TDM Min. A; Max. F. (EN ISO13997),
F. Impact Protection P=Pass
PROTECTIVE GLOVES AGAINST MECHANICAL RISKS. Protection levels are measured from area of glove palm. Warning: For gloves with two or more layers the overall classification of EN 388:2016 does not necessarily reflect the performance of the outmost layer. Do not use these gloves near moving elements or machinery with unprotected parts. For dulling during the cut resistance test, the coupe test results are only indicative while the TDM cut resistance test is the reference performance result.
SUITABLE FOR CONTACT WITH FOOD SPECIFIED IN REGULATION (EU) 10/2011 AND
1935/2004.
All gloves/sleeves that are suitable for foodstuff may not be suitable for all
types of food. To know for which foodstuff the glove/sleeve may be used please
see the Food declaration of conformity. Contact Ejendals for more information
EN 420:2003 + A1:2009 PROTECTIVE GLOVES – GENERAL REQUIREMENTS AND TEST
METHODS
Finger dexterity test: Min. 1; Max. 5
FITTING AND SIZING
All sizes comply with the EN 420:2003+A1:2009 for comfort, fit and dexterity, if not explained on the front page. If the short model symbol is shown on the front page, the glove is shorter than a standard glove, in order to enhance the comfort for special purposes – for example fine assembly work. Only wear the products in a suitable size. Products which are either too loose or too tight will restrict movement and will not provide the optimal level of protection.
STORAGE AND TRANSPORT: Ideally stored in dry and dark condition in the original package, between +10º – +30ºC.
INSPECTION BEFORE USE
Check that the glove does not present holes, cracks, tears, colour change etc.
If the product becomes damaged it will NOT provide the optimal protection and
must be disposed of. Never use a damaged product.
SHELF LIFE: The nature of the materials used in this product means that
the life of this product cannot be determined as it will be affected by many
factors, such as storage conditions, usage etc.
CARE AND MAINTENANCE
The user bares sole responsibility for submitting the product to mechanical
washing after use, as unknown substances can contaminate the product during
use and may affect the performance levels of the product. To care for your
product, we recommend that you rinse in cold water and line dry in room
temperature.
DISPOSAL: According to local environmental legislations.
EN ISO 21420: The glove contains natural rubber which may cause allergy.
ALLERGENS: This product may contain components that may be a potential
risk to allergic reactions. Do not use in case of hypersensitivity signs. For
more information contact Ejendals.
LATEX FREE YES NO
DECLARATION OF CONFORMITY
www.ejendals.com/conformity
OUTER MATERIAL SPECIFICATION Nitrile
INNER MATERIAL SPECIFICATION Nylon, elastane
EU-TYPE EXAMINATION 0075 CTC, 4 rue Hermann Frenkel, 69367 Lyon Cedex 07
France
Support
Ejendals ab
Limavägen 28, SE-793 32 Leksand, Sweden
Phone: +46 (0) 247 360 00
Fax: +46 (0) 247 360 10
info@ejendals.com
order@ejendals.com
www.ejendals.com
Declaration of Conformity
www.ejendals.com/conformity
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>