TEGERA 8802 Infinity Glove Instruction Manual

June 4, 2024
TEGERA

8802 Infinity Glove
Instruction Manual

EN 420:2003
+ A1:2009| EN 388:2016
4121X| EN 407:2004
X1XXXX
---|---|---
| |

INSTRUCTIONS FOR USING CATEGORY II

SEE THE FRONT PAGE FOR PRODUCT-SPECIFIC INFORMATION
Carefully read these instructions before using this product.
EXPLANATION OF PICTOGRAMS 0 =
Below the minimum performance level for the given individual hazard X= Not submitted to  the test or test method not suitable or the glove design or material
Warning! This product is designed to provide protection specified in PPE Regulation (EU) 2016/425 with the detailed levels of performance presented below. However, always remember that no item of PPE can provide full protection and caution must always be taken when exposed to risks.
PROTECTIVE GLOVES AGAINST THERMAL RISKS (HEAT AND/OR FIRE)

ABCDEF
A: Burning behavior
B: Contact heat
C: Convective heat
D: Radiant heat
E: Small splashes of molten metal
F: Large quantities of molten metal
PERFORMANCE (A-F)
Min. 0; Max. 4
Warning: EN 407:2004: if the glove consists of separate parts which are not permanently interconnected, the performance levels and the protection only apply to the complete assembly. If the gloves have a performance level 1, 2, or X in burning behavior in EN 407:2004 the gloves should not come in contact with a naked flame.

**EN 388:2016

A. Abrasion resistance
B. Blade cut resistance.
C.Tear resistance
D. Puncture resistanceE. Cut Resistance TDM (EN ISO13997),
F. Impact Protection
Min. 0; Max. 4
Min. 0; Max. 5
Min. 0; Max. 4
Min. 0; Max. 4
Min. A; Max. F
PROTECTIVE GLOVES AGAINST MECHANICAL RISKS. Protection levels are measured from an area of the glove palm. Warning: For gloves with two or more layers the overall classification of EN 388:2016 does not necessarily reflect the performance of the outmost layer. Do not use these gloves near moving elements or machinery with unprotected parts. For dulling during the cut resistance test, the coupe test results are only indicative while the TDM cut resistance test is the reference performance result.
ABCDEF

** SUITABLE FOR CONTACT WITH FOOD SPECIFIED IN REGULATION (EU) 10/2011 AND 1935/2004. All gloves/sleeves that are suitable for foodstuff may not be suitable for all types of food. To know for which foodstuff the glove/sleeve may be used please see the Food declaration of conformity. Contact Ejendals for more information.
EN 420:2003 + A1:2009 PROTECTIVE GLOVES – GENERAL REQUIREMENTS AND TEST METHODSFinger dexterity test: Min. 1; Max. 5

**FITTING AND SIZING

**

All sizes comply with EN 420:2003+A1:2009 for comfort, fit, and dexterity, if not explained on the front page. If the short model symbol is shown on the front page, the glove is shorter than a standard glove, in order to enhance the comfort for special purposes – for example, fine assembly work. Only wear the products in a suitable size. Products that are either too loose or too tight will restrict movement and will not provide the optimal level of protection.
STORAGE AND TRANSPORT: Ideally stored in the dry and dark condition in the original package, between +10º – +30ºC.
INSPECTION BEFORE USE: Check that the glove does not present holes, cracks, tears, color changes, etc. If the product becomes damaged it will NOT provide the optimal protection and must be disposed of. Never use a damaged product. SHELF LIFE: The nature of the materials used in this product means that the life of this product cannot be determined as it will be affected by many factors, such as storage conditions, usage etc.
CARE AND MAINTENANCE: The user bares sole responsibility for submitting the product to mechanical washing after use, as unknown substances can contaminate the product during use and may affect the performance levels of the product. To care for your product, we recommend that you rinse in cold water and line dry in room temperature.
DISPOSAL: According to local environmental legislation.
EN ISO 21420: The glove contains natural rubber which may cause allergy.
ALLERGENS: This product may contain components that may be a potential risk to allergic reactions. Do not use in case of hypersensitivity signs. For more information contact Ejendals.
latex free:
OUTER MATERIAL SPECIFICATION
Nitrile
INNER MATERIAL SPECIFICATION
Nylon, elastane
EU-TYPE EXAMINATION
0075 CTC, 4 rue Hermann Frenkel, 69367 Lyon Cedex07 France

INFINITY™

OEKO-TEX®
CONFIDENCE IN TEXTILES
STANDARD 100
SE 14-214 Swerea IVF
Tested for harmful substances: www.oeko-tex.com/standard100

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals